Summary of Contents for New Water 400
- Page 1 New Water ® Chlorine Pool Care System Models 400/430 for pools up to 40,000 gallons Model 120 for pools up to 25,000 gallons The New Water® Cyclers and Replacement Cycler Pacs Customer Service 800-222-0169 www.kingtechnology.com...
-
Page 2: Table Of Contents
Swimming Pool Tips New Water® Cyclers Parts List Above Ground Model Parts List In Ground Models Base Installation Model 120 Filter Installation Model 120 In-Line Installation Model 400 Off-Line Installation Model 430 10-11 Troubleshooting Replacing a Cycler Pac Setting Control Dial Replacing Control Dial O-rings Replacing Cap O-rings &... -
Page 3: Introducing New Water
For In Ground Pools For Above Ground Pools New Water® Cycler The New Water® Cycler is on constant watch dispensing chlorine to control bacteria and provide a protective bank of sanitizer for your pool. Swimming Pool Tips 4. Add a stabilizer or con- 1. -
Page 4: New Water® Cyclers
New Water® Cycler Installation The New Water® Cycler comes in several different IN GROUND - Off-line models. Please review this list, determine which model you have and follow the appropriate installation instructions for that model only. Cycler Model #430 ABOVE GROUND POOLS... -
Page 5: Parts List Above Ground Model
Parts List • Model 120 8 & 9 SILICONE LUBRIC ANT Included with New Water® 120 Replacement Parts for New Water® 120 REF. # DESCRIPTION QTY. INCLUDED REF. # PART NO. DESCRIPTION 1 & 2 Cap w/O-Ring 1 & 2... -
Page 6: Parts List In Ground Models
Parts List • Models 400 and 430 INCLUDED WITH • Model 400 and 430 REF. # DESCRIPTION QTY. INCLUDED 1 & 2 Cap w/O-Ring Body Pressure Relief Valve 5, 6, 7 Control Dial with O-Rings 8 & 9 Knob with O-Ring... -
Page 7: Base Installation Model 120
TO POOL (slip x MPT) HOSE HOSE CLAMP CLAMP Isolating the New Water® Cycler by installing a corrosion resistant check valve is recommended. 2” Female Adapter (slip x FPT) 10 x 1 1/4” Phillips For better stability, the Pan Head Screws with New Water®... -
Page 8: Filter Installation Model 120
One 6” x 1 1/2” TBE PVC DO NOT OVER TIGHTEN. Nipple Screw adapter into the other ® side of New Water® Cycler. One Hose Adapter Hand tighten. Finish 1 1/2” x 1 1/2” x 1 1/4” tightening by turning 1 to 2 revolutions with wrench. -
Page 9: In-Line Installation Model 400
In Ground, In-line Installation - Model 400 TOOLS NEEDED Pipe Wrench • Install after all equipment and as far as possible from heater. • Any additional sanitizing equipment that is installed with New Hacksaw Water® Cycler must be installed after New Water®... -
Page 10: Off-Line Installation Model 430
DO NOT USE PIPE THREAD Two 90 TAPE as the threads Degree Elbows Screw a male adapter on these units are into each port of New Water® not suitable for Four Hose Cycler. Hand tighten. Finish this use and Clamps... - Page 11 New Water® Cycler base to secure the New Water® Cycler into a treated wood base. SCOOPS 2” – 36” APART Isolating the New Water® Cycler by installing a corrosion ON STRAIGHT PIPE resistant check valve is recommended.
-
Page 12: Troubleshooting
Chlorine Pac? more than is necessary. If loose or missing, it can 2. Reinsert the New Water® provide another avenue for Pac, lower the dial one 4. Contact your dealer to water to reach the chlorine. -
Page 13: Replacing A Cycler Pac
Rinse thoroughly before recycling or discarding in trash. Cut handle from New Water® Cycler Pac using a PVC cutting tool or a hacksaw (KEEP OUT OF REACH OF CHILDREN) Indent in plastic PVC cutting tool A. Find the... -
Page 14: Setting Control Dial
Set control dial on New Water® Cycler by matching up the parameters of your pool on the chart below. THIS IS A STARTING POINT ONLY and may need to be adjusted to fit your individual pool needs. See #2 below for adjusting directions. -
Page 15: Replacing Control Dial O-Rings
OTHER COPY? SILICONE LUBRICANT silicone lubricant that came with COPY COPY your New Water® Cycler on o-ring. COPY 4. Carefully insert control dial back into housing. 5. Push control dial completely into the housing and turn the dial to setting 2. -
Page 16: Replacing Cap O-Rings & Knobs
Models Model 120 400/430 6. If Pac still contains chlorine wrap in plastic bag and store • Back of 400/430 Cyclers in shed or cool well- and Cap of 400/430 Cyclers ventilated location away from children, pets, motorcycles, cars or anything metal that can rust, pit, etc. -
Page 17: For Proper Performance
C. OPTION 2 - A 3-Way Valve Installation • Any additional sanitizing equipment that is installed 3-way manual valve or 3-way motor valve plus controls with New Water® must be installed after New New Water® IN-FLOOR CYCLER Water®... -
Page 18: Warranty
The name of the nearest authorized dealer can be obtained by writing or calling King 4. This warranty is the exclusive warranty for the New Water® Technology at the address and telephone number provided Cycler. This warranty is not transferable. KING TECHNOLOGY below.