ZyXEL Communications ALC1024 User Manual
  1. Manuals
  2. Brands
  3. ZyXEL Communications Manuals
  4. Network Card
  5. ALC1024
  6. User manual
ZyXEL Communications ALC1024 User Manual

ZyXEL Communications ALC1024 User Manual

Adsl line card
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ALC1024
ADSL Line Card
Version 2.04
February 2004
User's Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ALC1024 and is the answer not in the manual?

Questions and answers

Related Manuals for ZyXEL Communications ALC1024

Summary of Contents for ZyXEL Communications ALC1024

  • Page 1 ALC1024 ADSL Line Card Version 2.04 February 2004 User’s Guide...

  • Page 2: Copyright

    ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation. All rights reserved. Disclaimer ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein.

  • Page 3: Interference Statements And Warnings

    ALC1024 User’s Guide Interference Statements and Warnings Interference Statement: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operations.

  • Page 4: Zyxel Limited Warranty

    ALC1024 User’s Guide ZyXEL Limited Warranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two years from the date of purchase. During the warranty period, and upon proof...

  • Page 5: Customer Support

    ALC1024 User’s Guide Customer Support Please have the following information ready when you contact customer support. Product model and serial number. Warranty information. Date that you received your device. Brief description of the problem and the steps you took to solve it.

  • Page 6: Table Of Contents

    ALC1024 with EEC Overview......................2-1 ALC1024 with Ethernet Extension Card Overview................2-1 Features of the ALC1024 with the Ethernet Extension Card ..............2-1 Default Settings of the ALC1024 with the Ethernet Extension Card ............. 2-2 Commands with EEC ..............................II Chapter 3 Commands with EEC Introduction....................
  • Page 7 ALC1024 User’s Guide Downstream and Upstream........................5-1 ATU-C and ATU-R..........................5-1 Profiles..............................5-1 Configured Versus Actual Rate ......................5-2 Default Settings ............................. 5-2 ADSL Commands..........................5-2 Chapter 6 10/100M Fast Ethernet Port Commands..................6-1 10/100M Auto-Sensing Ethernet Overview ................... 6-1 Ethernet Commands ..........................
  • Page 8 ALC1024 User’s Guide 11.4 SNMP Access Configuration ....................... 11-3 11.5 SNMP Trap Configuration ........................11-4 Chapter 12 Configuration Backup/Restore..................... 12-1 12.1 Configuration Backup/Restore Overview .................... 12-1 12.2 Configuration Files of the Line card..................... 12-1 12.3 Configuration Backup .......................... 12-1 12.4 Configuration Restore..........................
  • Page 9 ALC1024 User’s Guide Chapter 17 Getting Started Screens ......................17-1 17.1 Getting Started Overview ........................17-1 17.2 General Setup Screen......................... 17-1 17.3 Bridge Setup Screen ........................... 17-2 17.4 IP Setup Screen ..........................17-16 Chapter 18 Port Setup............................ 18-1 18.1 Port Setup Overview ........................... 18-1 18.2...
  • Page 10 ALC1024 User’s Guide Chapter 24 Diagnostic ............................ 24-1 24.1 Diagnostic Overview ..........................24-1 24.2 Line Card Diagnostic Screen....................... 24-1 24.3 Logout Screen ............................. 24-2 Chapter 25 Troubleshooting ........................... 25-1 25.1 DSL LED(s)............................25-1 25.2 Data Transmission..........................25-1 25.3 DSL LED(s) Turn On and Off ......................25-2 25.4...
  • Page 11 ALC1024 User’s Guide 29.5 Configured Versus Actual Rate ......................29-2 29.6 Default Settings ........................... 29-2 29.7 ALC Port Setup Screen ........................29-2 29.8 Channels ............................. 29-8 29.9 ALC Port Channel Setup Screen......................29-9 Chapter 30 IEEE 802.1Q VLAN ........................30-1 30.1...

  • Page 12: List Of Figures

    Figure 1-1 ALC1024 Front Panel..........................1-3 Figure 1-2 ASC1024 Front Panel ..........................1-3 Figure 1-3 ALC1024, ASC1024, and USER Telco-50 Pin Assignments..............1-4 Figure 1-4 CO Telco-50 Pin Assignments........................1-5 Figure 1-5 IES-2000 Telco-50 Cable Telco-50 Connector Pin Assignments ............. 1-6 Figure 1-6 IES-3000 Telco-50 Cable Right Telco-50 Connector Pin Assignments............
  • Page 13 ALC1024 User’s Guide Figure 8-8 SVLAN List Command Display Example ....................8-8 Figure 8-9 SVLAN Example ............................8-9 Figure 8-10 Example: Svlan Getentry 2 Command Display ................... 8-10 Figure 8-11 DVLAN List Command Display Example ..................... 8-11 Figure 8-12 DVLAN Getentry 2 Command Display Example ................. 8-11 Figure 8-13 VLAN List Command Display Example ....................
  • Page 14 ALC1024 User’s Guide Figure 19-1 Static VLAN Setup..........................19-4 Figure 19-2 Edit 802.1Q VLAN Static Entry ......................19-6 Figure 20-1 SNMP Setup ............................20-2 Figure 20-2 Edit SNMP Setup ..........................20-3 Figure 21-1 Logins..............................21-1 Figure 22-1 Maintenance............................22-1 Figure 22-2 Secured Client Setup ........................... 22-3 Figure 22-3 Edit Secured Client ..........................
  • Page 15 ALC1024 User’s Guide Figure 29-6 ALC Edit Port Channel Setup Screen ....................29-11 Figure 30-1 ALC Static VLAN Setup Screen ......................30-1 Figure 30-2 ALC Edit Static VLAN Screen ......................30-2 Figure 30-3 ALC Management VLAN Edit Screen ....................30-4 Figure 31-1 Card Firmware Upgrade ........................
  • Page 16 ALC1024 User’s Guide List of Tables Table 1-1 ALC1024 Front Panel Ports ........................1-3 Table 1-2 LED Descriptions ............................1-3 Table 1-3 ASC1024 Front Panel Ports ........................1-4 Table 1-4 Hardware Telco-50 Connector Port and Pin Numbers ................1-5 Table 1-5 Telco-50 Cable Telco-50 Pin Assignments ....................1-7 Table 3-1 Commands with EEC..........................
  • Page 17 ALC1024 User’s Guide Table 18-2 Ethernet Port Setup ..........................18-5 Table 18-3 ADSL Port Setup ........................... 18-6 Table 18-4 Profile Setting ............................18-7 Table 18-1 Static Route Setup..........................18-1 Table 18-2 Edit Static Route ............................ 18-2 Table 19-1 GARP Terminology ..........................19-3 Table 19-2 Static VLAN Setup ..........................
  • Page 18 ALC1024 User’s Guide Table 29-5 ALC Edit Port Setup..........................29-8 Table 29-6 ALC Port Channel Setup ........................29-9 Table 29-7 ALC Edit Port Channel Setup ......................29-11 Table 30-1 ALC Static VLAN Setup ......................... 30-1 Table 30-2 ALC Edit Static VLAN..........................30-2 Table 30-3 ALC Management VLAN Edit ........................

  • Page 19: Preface

    Naming Conventions The ALC1024 (ADSL Line Card) may be referred to as the ALC, the line card or the card. “ALC1024” refers to the ALC1024-61 and ALC1024-61L for ADSL over POTS (Annex A). “ALC1024” also refers to the ALC1024-63 and ALC1024-63L for ADSL over ISDN (Annex B) versions.
  • Page 20 ALC1024 User’s Guide Embedded web help for descriptions of individual screens and supplementary information. IES-2000 or IES-3000 User’s Guide Refer to the IES-2000 or IES-3000 User’s Guide for directions on installation, connections, maintenance, hardware trouble shooting and safety warnings. Management Switch Card User’s Guide This user’s guide provides hardware connection details and configuration and management instructions for the...

  • Page 21: Alc1024 Overview

    ALC 1024 Overview Part I: ALC1024 Overview This part introduces the general features default settings and hardware of the ADSL line card when you use the ADSL line card with the Ethernet extension card.

  • Page 23: Chapter 1 Alc1024 Overview

    This chapter introduces the ADSL line card’s general features, factory default settings and hardware. ALC1024 Overview The ALC1024 (ADSL Line Card) provides ADSL service for 24 subscribers over existing telephone wiring, thus avoiding the cost and hassle of installing new wiring. ADSL allows you to extend the reach of broadband services up to 18,000 feet.

  • Page 24: Default Settings

    ALC1024 Overview • System status (link status, rates, statistics counters) • Temperatures, voltage reports and alarms. Overheating Detection, Warning and Safegaurd The ALM LED turns on when the line card’s internal temperature is too high and turns off when the temperature has returned to a normal level.

  • Page 25: Front Panels

    Maximum Transmission Rate: 512 Kbps Front Panels Figure 1-1 ALC1024 Front Panel Figure 1-2 ASC1024 Front Panel Hardware Specifications These are the hardware details of the ALC1024 and ASC1024. 1.5.1 ALC1024 Ports Table 1-1 ALC1024 Front Panel Ports PORT DESCRIPTION ADSL This Telco-50 connector is for connecting to the ASC1024 (ADSL Splitter Card).

  • Page 26: Hardware Telco-50 Connector Pin Assignments

    This Telco-50 connector is for connecting to the ALC1024 (ADSL Line Card). 1.5.4 Fuse Ratings The ALC1024-61/63 uses one 5mm (D) x 20mm (L), T type, 4 amp, 250 Volt AC fuse. The ALC1024-61L/63L uses one 5mm (D) x 20mm (L), T type, 5 amp, 250 Volt AC fuse. 1.5.5 Weight ALC1024-61/63: 1.8 kg...

  • Page 27: Figure 1-4 Co Telco-50 Pin Assignments

    ALC1024 Overview Figure 1-4 CO Telco-50 Pin Assignments This table lists the ports and matching pin numbers for the hardware Telco-50 connectors. Table 1-4 Hardware Telco-50 Connector Port and Pin Numbers PORT NUMBER PIN NUMBER 25, 50 24, 49 23, 48...

  • Page 28: Telco-50 Cable Telco-50 Connector Pin Assignments

    ALC1024 Overview Table 1-4 Hardware Telco-50 Connector Port and Pin Numbers PORT NUMBER PIN NUMBER 7, 32 6, 31 5, 30 4, 29 3, 28 2, 27 Telco-50 Cable Telco-50 Connector Pin Assignments Use Telco-50 cables to connect the ADSL line card to the ADSL splitter card. The following diagrams show the pin assignments that you need to have on the Telco-50 connectors on the Telco-50 cables.

  • Page 29: Figure 1-6 Ies-3000 Telco-50 Cable Right Telco-50 Connector Pin Assignments

    ALC1024 Overview Figure 1-6 IES-3000 Telco-50 Cable Right Telco-50 Connector Pin Assignments The IES-3000 Telco-50 cable’s left Telco-50 connector connects to the DSL line card. Figure 1-7 IES-3000 Telco-50 Cable Left Telco-50 Connector Pin Assignments Table 1-5 Telco-50 Cable Telco-50 Pin Assignments...
  • Page 30 ALC1024 Overview Table 1-5 Telco-50 Cable Telco-50 Pin Assignments PORT NUMBER PIN NUMBER 18, 43 17, 42 16, 41 15, 40 14, 39 13, 38 12, 37 11, 36 10, 35 9, 34 8, 33 7, 32 6, 31 5, 30...

  • Page 31: Alc1024 With Eec Overview

    The following features and default settings apply to configuration and management of the ADSL line card when you use it with the EEC (Ethernet Extension Card). Refer to Chapter 1 ALC1024 Overview for a general introduction to the ALC1024 and features, default settings and hardware specifications that apply to the line card whether it is used with the management switch card or the Ethernet extension card.

  • Page 32: Default Settings Of The Alc1024 With The Ethernet Extension Card

    IGMP Snooping IGMP (Internet Group Management Protocol) snooping reduces multicast traffic for maximum performance. Default Settings of the ALC1024 with the Ethernet Extension Card These are the line card’s additional factory default settings when it is used with the Ethernet extension card.
  • Page 33 Speed used with auto-negotiation OFF: 100Mbps • Duplex mode used with auto-negotiation OFF: half duplex 2.3.5 Other Factory Defaults • MAC filter: Disabled • Secured Host: Disabled • Sys Error Log: Always Enabled • UNIX Syslog: Disabled ALC1024 With EEC Overview...

  • Page 34: Commands With Eec

    Commands with EEC Part II: Commands with EEC This part gives information on commands to use when you use the ADSL line card with the Ethernet extension card.

  • Page 35: Commands With Eec Introduction

    Commands with EEC Chapter 3 Commands with EEC Introduction This section introduces the command line interface and lists all of the commands that are available when you use the ADSL line card with the Ethernet extension card. Commands with EEC Overview You can use text command lines for software configuration.

  • Page 36: Commands With Eec

    Commands with EEC yields version - show system software version The system responds with a description of the version command. 3.1.3 Saving Your Configuration Always remember to save your configuration using the following syntax: 192.168.1.1> config save This command saves all system configurations into nonvolatile memory. Nonvolatile memory refers to the line card’s storage that remains even if the line card’s power is turned off.
  • Page 37 Commands with EEC Table 3-1 Commands with EEC COMMANDS DESCRIPTION MODULE COMMAND ATTRIBUTES <port> <any | ip | pppoe> This command sets the type of packets that a port is allowed forward. filter This command displays the filtering database. filterage This command displays the filter age time.
  • Page 38 Commands with EEC Table 3-1 Commands with EEC COMMANDS DESCRIPTION MODULE COMMAND ATTRIBUTES delete <portNo> <mac> This command deletes a source MAC address from which to forward packets. buffer list This command lists all buffer pools. info This command shows the current buffer pool’s information.
  • Page 39 Commands with EEC Table 3-1 Commands with EEC COMMANDS DESCRIPTION MODULE COMMAND ATTRIBUTES port <portName> This command shows information for the specified port. channel <portName> <channelNo> This command shows information on the specified channel of the specified port. system This command sets system attributes. port <portName>...
  • Page 40 Commands with EEC Table 3-1 Commands with EEC COMMANDS DESCRIPTION MODULE COMMAND ATTRIBUTES <addr> <data> This command writes 1 byte to the specified address. <addr> <data> This command writes 1 half-word to the specified address. <addr> <data> This command writes 1 word to the specified address.
  • Page 41 Commands with EEC Table 3-1 Commands with EEC COMMANDS DESCRIPTION MODULE COMMAND ATTRIBUTES speed <100 | 10> This command sets the operating speed of the Ethernet port (100M or 10M). status This command shows Ethernet link status (auto-negotiation, duplex, speed). save This command saves Ethernet settings.
  • Page 42 Commands with EEC Table 3-1 Commands with EEC COMMANDS DESCRIPTION MODULE COMMAND ATTRIBUTES rewrite <file> This command rewrites the boot area with the specified ISFS file. trace This command shows the trace level in the FLASHFS driver. <level> This command sets the trace level in the FLASHFS driver.
  • Page 43 Commands with EEC Table 3-1 Commands with EEC COMMANDS DESCRIPTION MODULE COMMAND ATTRIBUTES ports This command enables all ADSL ports. disable port <portNo> This command disables the specified ADSL port. ports This command disables all ADSL ports. lineinfo <portNo> This command shows the statistics of the specified ADSL ports.
  • Page 44 Commands with EEC Table 3-1 Commands with EEC COMMANDS DESCRIPTION MODULE COMMAND ATTRIBUTES profiles This command shows the contents of all profiles and profiles applied to all ADSL ports. getname <portNo> This command gets the name of the specified port. getnames This command gets the names of all ports.
  • Page 45 Commands with EEC Table 3-1 Commands with EEC COMMANDS DESCRIPTION MODULE COMMAND ATTRIBUTES abort <n> This command deletes the specified open underlying ATM device file no. arp [<list>] This command shows the IPATM ARP cache entries. arpserver <if> <addr> | here This command sets the ATM ARP server address on the specified interface.
  • Page 46 Commands with EEC Table 3-1 Commands with EEC COMMANDS DESCRIPTION MODULE COMMAND ATTRIBUTES accept [ all | <if> ] [ none | This command sets one or all interfaces <versionList> ] to either not accept RIP or accept a specific RIP version. allowed This command lists RIP versions allowed.
  • Page 47 Commands with EEC Table 3-1 Commands with EEC COMMANDS DESCRIPTION MODULE COMMAND ATTRIBUTES isfs trace This command shows the ISFS trace level. <level> This command sets the ISFS trace level. version This command shows version information for the ISFS module. version This command shows version information for the OAM module.
  • Page 48 Commands with EEC Table 3-1 Commands with EEC COMMANDS DESCRIPTION MODULE COMMAND ATTRIBUTES info This command shows the system information. name <name> This command sets the system name. contact <name> This command sets the contact person’s name. chassis <id> This command sets the chassis ID number.
  • Page 49 Commands with EEC Table 3-1 Commands with EEC COMMANDS DESCRIPTION MODULE COMMAND ATTRIBUTES svlan setentry <vid> <portNo> This command sets a static VLAN entry to normal untagged. setentry <vid> <portNo> This command sets a static VLAN entry to <ad_control> <ad_control> untagged. setentry <vid>...

  • Page 51: Chapter 4 System Commands

    Commands with EEC Chapter 4 System Commands This chapter describes the line card’s system-related commands. System Commands Overview Use the commands described in this chapter to configure system functions when you use the line card with the Ethernet extension card. Commonly Used Commands This section shows you commonly used commands.

  • Page 52: Sys Commands

    Commands with EEC This command instructs the system to perform a configuration save and then a warm start, that is, restarting the system without turning the power off and on. 4.2.4 Password Command Syntax: 192.168.1.1> passwd This command changes the management password. The management password is used for authentication at Telnet login.

  • Page 53: Set Name Command

    Commands with EEC 4.3.2 Set Name Command Syntax: 192.168.1.1 sys> set name <name> This command allows you to set the name of your line card. The previous setting will be cleared if the command is entered with the <name> parameter omitted. 4.3.3 Set Contact Command Syntax:...

  • Page 54: Secured Host Command

    Commands with EEC 4.4.1 Secured Host Command Syntax: 192.168.1.1 sys> secured host [<mode>] where <mode> enable disable If <mode> = disable (default), then anyone may access your line card. If <mode> = enable, then only those users with IP addresses specified by you may access your line card (refer to the Secured Host Add command).

  • Page 55: Syslog Command

    Commands with EEC If your UNIX server is down these logs will be lost. 4.5.1 Syslog Command Syntax: 192.168.1.1 sys> syslog [<mode>] where <mode> enable disable This command enables or disables the sending of logs to your UNIX server. The default is disabled (<mode>= disable).

  • Page 56: Figure 4-2 Example: Procedure To Save And View A Previous Error Log

    Commands with EEC Incorrect telnet password (IP address) Insecure telnet access FTP session begin FTP session end Incorrect FTP password (IP address) Insecure FTP access FTP image error (reason) FTP receive file OK (file name) System reboot Out of buffer 4.6.1 Errlog Display Command Syntax:...

  • Page 57: Set Chassis Command

    Commands with EEC This command displays the slot number for this line card in the chassis. This is an optional parameter to help keep track of individual line cards. 4.6.5 Set Chassis Command Syntax: 192.168.1.1 sys> set chassis <chassis number> where <chassis number>= The number for the IES-2000 or IES-3000 chassis (1 to 64).

  • Page 59: Chapter 5 Adsl Commands

    Commands with EEC Chapter 5 ADSL Commands The ADSL (Asymmetrical Digital Subscriber Line) subsystem allows you to configure and monitor the line card’s ADSL ports. ADSL Standards Overview The line card supports both the G.lite and the G.dmt standards. G.lite is intended to minimize the cost for the consumer market.

  • Page 60: Configured Versus Actual Rate

    G.dmt standard. Configure a profile with a maximum downstream rate of 1536 Kbps or less for use with G.lite. Refer to the ALC1024 Overview chapter for the settings of the default profile and ADSL port default settings. ADSL Commands Enter at the command prompt to enter the ADSL subsystem of commands.
  • Page 61 Commands with EEC where A port number, from 1 to 24. <port number> = command forcibly disables the specified ADSL port. disable port All ADSL ports are disabled by default. A port must be enabled before data transmission can occur. An enabled but disconnected ADSL port generates more heat than an operating port. To minimize heat generation and to enhance reliability, remember to disable a port when it is not in use.

  • Page 62: Figure 5-1 Linedata Command Example

    Commands with EEC minimize heat generation and to enhance reliability, remember to disable a port when it is not in use. 5.7.6 Linedata Command Syntax: 192.168.1.1 adsl> linedata <port number> where A port number, from 1 to 24. <port number> The linedata command shows the line bit allocation of an ADSL port.

  • Page 63: Figure 5-2 Lineinfo Command Example

    Commands with EEC 192.168.1.1 adsl> lineinfo 7 Current Operating Modes: Data Mode: ATM Service Type in operation: G.DMT Number of Channels (Down/up stream): 1/1 Downstream Framing Structure Active down/up stream rate option : 1/1 TRELLIS operation mode is : ON Current Connection detail: Down/up stream interleaved Delay : 4/ 4 ms...

  • Page 64: Figure 5-3 Lineperf Command Example

    Commands with EEC 192.168.1.1 adsl> lineperf 7 nfebe-I/nfebe-ni : 0/0 ncrc-I/ncrc-ni : 0/0 nfecc-I/nfecc-ni : 0/0 nfec-I/nfec-ni : 0/0 nblks-ds/nblks-us : 120878/120878 nsec-ds/nsec-us : 2060/2060 n-eb-ds/n-eb-us : 0/0 n-bbe-ds/n-bbe-us : 0/0 n-es-ds/n-es-us : 0/0 n-ses-ds/n-ses-us : 0/0 non-ses-blks-ds/non-ses-blks-us : 120878/120878 n-uas-ds/n-uas-us : 0/0 fe_loss_seconds/ne_loss_seconds : 0/0...

  • Page 65: List Port Command

    Commands with EEC Downstream and upstream noise margins must both be at least 6 dB. The initial downstream and upstream noise margins are first set during training. The upstream margin is recalculated every 15 seconds during “show time” at the ATU-C and the downstream margin updates every 15 seconds during “show time” by using EOC messaging. Information obtained prior to training to steady state transition will not be valid or will be old information.

  • Page 66: Figure 5-5 Set Profile Command Example

    Commands with EEC <atuc min margin> The minimum acceptable ADSL signal/noise margin (0..31db) for traffic going out from the line card to the subscriber’s ADSL device. <atur max margin> The maximum acceptable ADSL signal/noise margin (0..31db) for traffic coming to the line card from the subscriber’s ADSL device. <atuc max margin>...

  • Page 67: Figure 5-6 List Profiles Command Example

    Commands with EEC 5.7.14 List Profiles Command Syntax: 192.168.1.1 adsl> list profiles command displays all of the configured ADSL profiles and the ADSL ports that use each. list profiles An example is shown next. 192.168.1.1 adsl> list profiles Profile 1 : DEFVAL Profile 2 : debug Port 1, Profile : DEFVAL Port 2, Profile : DEFVAL...

  • Page 68: Figure 5-7Show Profile Command Example

    Commands with EEC 192.168.1.1 adsl> show profile debug #Entry type : adslLineConfProfileEntry ConfProfileName : debug AtucConfTargetSnrMgn : 6 db AtucConfMaxSnrMgn : 31 db AtucConfMinSnrMgn : 0 db AtucChanConfInterleaveMinTxRate : 32 Kbps AtucChanConfInterleaveMaxTxRate : 8000 Kbps AturConfTargetSnrMgn : 6 db AturConfMaxSnrMgn : 31 db AturConfMinSnrMgn : 0 db AturChanConfInterleaveMinTxRate : 32 Kbps AturChanConfInterleaveMaxTxRate : 800 Kbps...

  • Page 69: Figure 5-8 Show Profiles Command Example

    Commands with EEC 192.168.1.1 adsl> show profiles #Entry type : adslLineConfProfileEntry ConfProfileName : DEFVAL AtucConfTargetSnrMgn : 6 db AtucConfMaxSnrMgn : 31 db AtucConfMinSnrMgn : 0 db AtucChanConfInterleaveMinTxRate : 32 Kbps AtucChanConfInterleaveMaxTxRate : 2048 Kbps AturConfTargetSnrMgn : 6 db AturConfMaxSnrMgn : 31 db AturConfMinSnrMgn : 0 db AturChanConfInterleaveMinTxRate : 32 Kbps AturChanConfInterleaveMaxTxRate : 512 Kbps...

  • Page 70: Figure 5-9 Set Port Command Example

    Commands with EEC When the mode is set to and the negotiated mode is , the actual rates are governed auto glite by G.lite, regardless of the configured numbers. An example is shown next. 192.168.1.1 adsl> set port 4 debug auto Figure 5-9 Set Port Command Example This command sets ADSL port 4 to have the debug profile.

  • Page 71: Show Ports Command

    Commands with EEC 5.7.20 Show Ports Command Syntax: 192.168.1.1 adsl> show ports command shows the line status (up or down), the actual incoming and outgoing rates and the show ports mode of all ADSL ports. 5.7.21 Set PVC Command Syntax: 192.168.1.1 adsl>...

  • Page 72: Show Pvc Command

    Commands with EEC The set pvcs command allows you to configure a single PVC for all of the ADSL ports at once. The <rx vpi> and <rx vci> settings will be equal to those of <tx vpi> and <tx vci> if the rx settings are not configured.

  • Page 73: 10/100M Fast Ethernet Port Commands

    Commands with EEC Chapter 6 10/100M Fast Ethernet Port Commands The Ethernet subsystem allows you to configure and monitor the 10/100M fast Ethernet port that connects to the backplane. 10/100M Auto-Sensing Ethernet Overview The line card’s rear Ethernet port is auto-sensing and supports connections to a 10 or 100Mbps Ethernet. Connect to the EEC’s Ethernet port in order to connect to the line card’s rear Ethernet port.
  • Page 74 Commands with EEC 6.2.3 Set Speed Command Syntax: 192.168.1.1 ethernet> set speed <speed> where <speed> = 10 This command sets the connection speed used when auto-negotiation is turned off. 10 stands for 10Mbps and 100 stands for 100Mbps. 6.2.4 Status Command Syntax: 192.168.1.1 ethernet>...

  • Page 75: Chapter 7 Bridge Commands

    Commands with EEC Chapter 7 Bridge Commands This chapter discusses the bridge subsystem. It allows you to configure and monitor bridging, configure MAC filters, port-based VLANs and tagged frame functions of the line cards. Bridging Overview The line card supports IEEE 802.1D transparent bridging; but not the static filtering feature or spanning tree protocol.

  • Page 76: Mac Filter Commands

    Commands with EEC 7.4.1 Config Save Command Syntax: 192.168.1.1 bridge> config save This command saves the bridge configuration into nonvolatile memory. You must use this command to save any configurations that you make, otherwise the line card will return to its default settings when it is restarted. Do not turn off your IES-2000/3000 while saving your configuration.

  • Page 77: Mac Filter Enable Command

    Commands with EEC 7.5.2 MAC Filter Enable Command Syntax: 192.168.1.1 bridge> macfilter enable [<port>] where <port> A bridge port number. This command enables the MAC filtering feature on a specific port or on all ports if no port number is specified.

  • Page 78: Filter Commands

    Commands with EEC Filter Commands Below is a list of commonly-used filter commands. 7.6.1 Filter Command Syntax: 192.168.1.1 bridge> filter This command displays the filtering database. 7.6.2 Mfilter Command Syntax: 192.168.1.1 bridge> mfilter This command displays the multicast filtering database. The mfilter command allows you to monitor the line card’s IGMP snooping activities.

  • Page 79: Port-Based Vlan Commands

    Commands with EEC Max Response Time = The longest period of time used to respond to a query packet, measured in tenths of a second. The time period between query packets. Query Interval 7.6.3 Filterage Command Syntax: 192.168.1.1 bridge> filterage [age] where Aging out timer period in seconds.
  • Page 80 Commands with EEC In a port-based VLAN, the allowable outgoing port(s) of each incoming port must be defined. Ethernet frames are forwarded according to these rules. Therefore, if you wish to allow two subscriber ports to talk to each other, for example, between conference rooms in a hotel, you must define the egress port (outgoing port) for both ports.

  • Page 81: Figure 7-2 Default Vlan Settings

    Commands with EEC Figure 7-2 Default VLAN Settings 7.7.1 Portfilter Command Syntax: 192.168.1.1 bridge> portfilter [<source port> all|<dest ports>] where <source port> = An incoming bridge port number. All bridge ports are allowed outgoing ports. <dest ports> The outgoing bridge ports. Separate by a space if there is more than one port. This command sets or displays the port-based VLAN configuration.

  • Page 82: Figure 7-3 Port Filter Command Example

    Commands with EEC 192.168.1.1 > bridge 192.168.1.1 bridge> portfilter Port 1 (ethernet): Port 2 (dsl1): Port 3 (dsl2): Port 4 (dsl3): Port 5 (dsl4): Port 6 (dsl5): Port 7 (dsl6): Port 8 (dsl7): Port 9 (dsl8): Port 10 (dsl9): Port 11 (dsl10): Port 12 (dsl11): Port 13 (dsl12): Port 14 (dsl13):...

  • Page 83: Figure 7-5 Port Filter Command Example: Display Configuration

    Commands with EEC 192.168.1.1 bridge> portfilter Port 1 (ethernet): Port 2 (dsl1): Port 3 (dsl2): Port 4 (dsl3): Port 5 (dsl4): Port 6 (dsl5): Port 7 (dsl6): Port 8 (dsl7): Port 9 (dsl8): Port 10 (dsl9): Port 11 (dsl10): Port 12 (dsl11): Port 13 (dsl12): Port 14 (dsl13): Port 15 (dsl14):...

  • Page 84: Tagged Ethernet Frames Commands (Fast Mode)

    Commands with EEC Figure 7-7 Example of Modified VLAN Port 3 The following figure illustrates that port 1 (the Ethernet port) is linked to ports 2 (DSL port 1) and 3 (DSL port 2). Ports 2 (DSL port1) and 3 (DSL port 2) are also linked to each other. Or, in other words, the following figure is a result of the following commands: 192.168.1.1 bridge>...

  • Page 85: Table 7-1 Physical Ports, Port Numbers And Line Card Default Pvid Tags In Fast Mode

    Commands with EEC Ethernet frame. Allocate tag numbers for all logical ports on your line card. This command lets you allocate IEEE 802.1Q identification numbers (tags) on a port-by-port basis. The command 192.168.1.1 bridge> fpvid displays the default port identification of all line card ports.

  • Page 87: Chapter 8 Ieee 802.1Q Tagged Vlan Commands

    Commands with EEC Chapter 8 IEEE 802.1Q Tagged VLAN Commands This chapter describes the IEEE 802.1Q Tagged VLAN and associated commands. IEEE 802.1Q Tagged VLAN Overview The IEEE 802.1Q Tagged VLAN allows your line card to deliver tagged/untagged frames to and from its ports. The standard gives the line card the ability to recognize VLAN-aware and VLAN-unaware devices and automatically strips tagged frames destined for ports that would normally drop tagged frames.

  • Page 88: Configuring The Tagged Vlan

    Commands with EEC 8.4.2 Dynamic Entries (DVLAN Table) Dynamic entries are learned by the bridge and cannot be created or updated by administrators. The bridge learns this information by observing what port, source address and VLAN ID (or VID) is associated with a frame. Entries are added and deleted using GARP VLAN Registration Protocol (GVRP), where GARP is the Generic Attribute Registration Protocol.

  • Page 89: Figure 8-1 Tagged Vlan Configuration Example

    Commands with EEC 192.168.1.1> vlan1q 192.168.1.1 vlan1q> svlan setentry 11 2 fixed untag 192.168.1.1 vlan1q> svlan setentry 11 1 fixed tag 192.168.1.1 vlan1q> pvid 2 11 192.168.1.1 vlan1q> svlan setentry 12 3 fixed untag 192.168.1.1 vlan1q> svlan setentry 12 1 fixed tag 192.168.1.1 vlan1q>...

  • Page 90: Ieee 802.1Q Tagged Vlan Commands

    Commands with EEC IEEE 802.1Q Tagged VLAN Commands Bridge port 1 stands for the Ethernet port, bridge port 2 stands for DSL port 1, bridge port 3 stands for DSL port 2, and so on. 8.6.1 Enabling the IEEE 802.1Q Tagged VLAN The IEEE 802.1Q Tagged VLAN is disabled by default.

  • Page 91: Figure 8-4 Vlan Status Command Example

    Commands with EEC 192.168.1.1 vlan1q> vlan status IEEE 802.1Q VLAN : DISABLED VLAN Egress Ports Untagged Ports C E 12345678 12345678 12345678 C E 12345678 12345678 12345678 ================================================================================ - v vvvvvvvv vvvvvvvv vvvvvvvv v v vvvvvvvv vvvvvvvv vvvvvvvv Total 1 VLAN(s). The default port VLAN id of all bridge ports: Port 0 (CPU):...

  • Page 92: Figure 8-5 Pvid Command Display Example

    Commands with EEC pvid port# ----- ----- Figure 8-5 PVID Command Display Example 8.6.5 SVLAN CPU Command Syntax: 192.168.1.1 vlan1q> svlan cpu [<vid>] where <vid> VLAN ID. Valid parameter range = [1 – 4094]. This command registers your CPU as a port member of the static VLAN (SVLAN) with <vid>. To display the CPU static VLAN identification, simply enter the command without parameters.

  • Page 93: Figure 8-6 Example: Svlan List Command Display

    Commands with EEC port# ad_control tag_control -------- ------- ------------ ------------ fixed normal UnTag normal UnTag normal UnTag fixed UnTag normal UnTag normal UnTag normal UnTag fixed UnTag Figure 8-6 Example: SVLAN List Command Display For more information about the command display, refer to the command (shown svlan list svlan setentry...

  • Page 94: Figure 8-7 Modifying The Static Vlan Example

    Commands with EEC 192.168.1.1 vlan1q> svlan setentry fixed untag 192.168.1.1 vlan1q> svlan setentry fixed untag 192.168.1.1 vlan1q> svlan setentry fixed 192.168.1.1 vlan1q> svlan list Figure 8-7 Modifying the Static VLAN Example The arrows, in the next figure, point to the lines in the static VLAN table that have been modified as a result of the previous commands.

  • Page 95: Figure 8-9 Svlan Example

    Commands with EEC Figure 8-9 SVLAN Example An untagged frame comes in from the LAN. An untagged frame comes in from the LAN. Step 1. The switch checks the PVID table and assigns a temporary VID of 1. Step 2. The switch ignores port# 1 (the LAN port where the frame came in), because the switch does not send a Step 3.

  • Page 96: Figure 8-10 Example: Svlan Getentry 2 Command Display

    Commands with EEC 8.6.8 SVLAN Getentry Command Syntax: 192.168.1.1 vlan1q> svlan getentry <vid> where <vid> VLAN ID. Valid parameter range = [1 – 4094]. This command displays an entry with a specified VLAN ID in the static VLAN table. Display a Static VLAN Table Entry Example The following figure is an example display of the following command.

  • Page 97: Figure 8-11 Dvlan List Command Display Example

    Commands with EEC ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >>...

  • Page 98: Figure 8-13 Vlan List Command Display Example

    Commands with EEC ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- Figure 8-13 VLAN List Command Display Example In the figure above “O" denotes “egress port”, “V” denotes “tagged” and “X” denotes “ untagged”. 8-12 IEEE 802.1QTagged VLAN Commands...

  • Page 99: Chapter 9 Ieee 802.1P Priority Commands

    Commands with EEC Chapter 9 IEEE 802.1p Priority Commands This chapter explains IEEE 802.1p Priority commands. IEEE 802.1p Priority Overview IEEE 802.1p Priority commands assign priority levels to individual ports. IEEE 802.1p defines up to eight priorities (0-7) by inserting a tag into a MAC-layer frame that contains bits to define priority of service. IEEE 802.1p Priority Commands Bridge port 1 stands for the Ethernet port, bridge port 2 stands for DSL port 1, bridge port 3 stands for DSL port 2, and so on.
  • Page 100 Commands with EEC <regened priority> = The regenerated user priority the incoming user priority is mapped to for <port #>. Valid parameter range = [0 - 7], where 0 is the lowest priority and 7 is the highest priority. This command changes the priority of a tagged frame from a specified ingress port from the original user priority to the regened priority.

  • Page 101: Chapter 10 Ip Commands

    Commands with EEC Chapter 10 IP Commands This chapter shows you how to configure the IP parameters. 10.1 IP Commands Overview More often than not, you have more than one DSL line card for a particular installation. The IP host implementation in the line cards allows you to manage them over the network.

  • Page 102: Config Command

    Commands with EEC Line 4 adds the new default route. The default route tells the system where the gateway (next hop) is when the line card sends packets to a destination that is not on the same subnet as the line card. Line 5 saves the new configuration to the nonvolatile memory.

  • Page 103: Ping Command

    Commands with EEC 192.168.1.1 ip> config [save] This command shows the IP configuration. The save option saves the configuration to the nonvolatile memory. 10.3.2 Version Command Syntax: 192.168.1.1 ip> version This command shows the firmware version and date on the line card. 10.3.3 Ping Command Syntax:...

  • Page 104: Subnet Delete Command

    Commands with EEC This command defines a subnet. Type “subnet” without any parameters to view a list of the configured subnets. 10.3.6 Subnet Delete Command Syntax: 192.168.1.1 ip> subnet delete <net name> where <net name> The name of the subnet. This command removes a subnet.

  • Page 105: Route Delete Command

    Commands with EEC 10.3.9 Route Delete Command Syntax: 192.168.1.1 ip> route delete <dom name> where <dom name> The name of the static route. This command removes a static, IP forwarding route. 10.3.10 Route Flush Command Syntax: 192.168.1.1 ip> route flush This command removes all of the static IP forwarding routes.

  • Page 107: Chapter 11 Remote Management

    Commands with EEC Chapter 11 Remote Management This chapter shows you how to manage the line card from a remote location. 11.1 Remote Management Overview The line card’s remote management features make it easy and convenient to manage the line card from remote locations.

  • Page 108: Figure 11-1 Snmp Management Model

    Commands with EEC Figure 11-1 SNMP Management Model An SNMP managed network consists of two main component types: agents and a manager. An agent is a management software module that resides in a managed device (the line card). An agent translates the local management information from the managed device into a form compatible with SNMP.

  • Page 109: Snmp Access Configuration

    Commands with EEC ♦ Trap Used by the agent to inform the manager of some events. 11.3.1 Supported MIBs The line card supports MIB II that is defined in RFC 1213 and RFC 1215 as well as transparent bridge MIBs defined in RFC 1493.

  • Page 110: Snmp Trap Configuration

    Commands with EEC access flush This command revokes access by any and all manager stations. 11.4.4 SNMP Access List Command Syntax: access list This command shows the allowed access. 11.5 SNMP Trap Configuration The line card uses the SNMP trapping facility to proactively report unusual events to one or more trap servers. To configure the trap parameters, use the commands in the SNMP subsystem.

  • Page 111: Trap Delete Command

    Commands with EEC The password used by the line card to authenticate itself to the trap server. <community> The IP address of the trap server. <IP addr> This command adds a trap server. 11.5.3 Trap Delete Command Syntax: trap delete <community> <IP addr> This command deletes a trap destination.

  • Page 113: Configuration Backup/Restore

    Commands with EEC Chapter 12 Configuration Backup/Restore This chapter describes the process for backing up your user settings (configuration) from the line card onto your computer and how to restore them to the line card. 12.1 Configuration Backup/Restore Overview The line card uses FTP for configuration backup/restore through its built-in FTP server. You can use any FTP client (for example, ftp.exe in Windows) to backup/restore the line card’s configuration.

  • Page 114: Configuration Restore

    Commands with EEC 12.4 Configuration Restore You can restore configuration files from your computer to the line card. Restore the system configuration by following the example shown next. Do not turn off the line card during the restore process, as it may corrupt the firmware and make your line card unusable.

  • Page 115: Firmware Upload And Recovery

    Commands with EEC Chapter 13 Firmware Upload and Recovery This chapter describes how to load new firmware onto your line card or recover firmware that is in the non-volatile memory. 13.1 Firmware Upload and Recovery Overview The line card uses FTP to upload firmware. If the firmware in non-volatile memory is damaged, the line card uses BOOTP/TFTP to recover the firmware.

  • Page 116: Emergency Console Port

    Commands with EEC Enter the management password (1234 by default). For example, Password: 1234 230 Logged in Transfer the firmware file to the line card. For example, ftp> put 201AS0b1.img image where 201AS0b1.img = The firmware file that you want to upload. = The internal firmware name in the line card.

  • Page 117: Figure 13-1 Bootp/Tftp Server

    Commands with EEC Do not turn off the IES-2000/3000 during the updating process, as it may corrupt the firmware and make your unit unusable. Telnet to your line card’s IP address (192.168.1.1 is the default). Run BootpTftp.exe, to bring up the following window. Click New to create a MAC address entry.

  • Page 118: Figure 13-3 Database Edit Dialog

    Commands with EEC Figure 13-3 Database Edit Dialog Select Normal Bootp to enable normal BOOTP/TFTP functions. Figure 13-4 Enable BOOTP/TFTP See section 13.3 on the emergency console port. Restart the line card and press any key within three seconds to get the following screen. 13-6 Firmware Upload and Recovery...

  • Page 119: Figure 13-5 Enter Debug Mode

    Commands with EEC SDRAM Testing ... Mac address 00:A0:C5:12:34:56 Figure 13-5 Enter Debug Mode Press any key at the “Press any key within 3 seconds to enter debug mode ………………” message, to enter the debug mode. Enter atnb at the line card boot console. Wait for the firmware upload to finish.

  • Page 121: Troubleshooting With Eec

    Commands with EEC Chapter 14 Troubleshooting with EEC This chapter covers potential problems and possible remedies. After each problem description, some steps are provided to help you to diagnose and to solve the problem. 14.1 DSL LED(s) A DSL LED is not on. Table 14-1 Troubleshooting the DSL LED(s) STEPS CORRECTIVE ACTION...

  • Page 122: Dsl Led(S) Turn On And Off

    Commands with EEC Table 14-2 Troubleshooting Data Transmission STEPS CORRECTIVE ACTION If you cannot ping, connect a DSL modem to a DSL port (that is known to work) on the same line card. If the DSL modem or router works with a different DSL port, there may be a problem with the original port.

  • Page 123: Local Server

    Commands with EEC Table 14-6 Troubleshooting the Password CORRECTIVE ACTION Refer to section 13.4 to upload the default configuration file. This returns all of the settings to default values, so you lose any configurations you have made. 14.7 Local Server The computer behind a DSL modem or router cannot access a local server connected to the IES-2000/3000.
  • Page 124 Commands with EEC Table 14-9 Troubleshooting Telnet STEPS CORRECTIVE ACTION Ping the line card from your computer. If you are able to ping the line card but are still unable to telnet, contact the distributor. If you cannot, check the cable, connections and IP configuration (see the chapter on IP Commands).

  • Page 125: Web Configurator With Eec 1

    Web Configurator with EEC 1 Part III: Web Configurator with EEC 1 This part tells how to access and navigate the web configurator and perform initial configuration. It also describes the Getting Started web configurator screens when you use the ADSL line card with the Ethernet extension card.

  • Page 127: Chapter 15 Web Configurator With Eec Introduction

    Web Configurator with EEC 1 Chapter 15 Web Configurator with EEC Introduction This chapter describes how to log into the web configurator and navigate through it. 15.1 Web Configurator with EEC Overview The embedded web configurator allows you to use a web browser to manage the line card. 15.2 Accessing the Web Configurator You will need a computer with an Ethernet 10BaseT, 100Base-TX Network Interface Card (NIC).

  • Page 128: Home Screen

    Web Configurator with EEC 1 15.3 Home Screen This is the web configurator home screen. Click a link on the navigation panel to go to the corresponding screen. Figure 15-2 Home Screen The following table describes this screen. Table 15-1 Navigation Panel Links LABEL DESCRIPTION Getting Started...

  • Page 129: Help

    Web Configurator with EEC 1 SNMP This link takes you to a screen where you can set up Simple Network Management Protocol. Logins This link takes you to a screen where you can change passwords. Maintenance This link takes you to screens where you can set UNIX syslog parameters, the time and date and remote management;...

  • Page 130: Saving Your Configuration

    Web Configurator with EEC 1 15.6 Saving Your Configuration Click Apply to save your changes back to the line card's volatile memory. The line card loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to the left to save your changes to the non-volatile memory when you are done configuring.

  • Page 131: Figure 15-4 Adsl Port Setup Example

    Web Configurator with EEC 1 Figure 15-4 ADSL Port Setup Example Web Configurator with EEC Introduction 15-5...

  • Page 133: Chapter 16 Initial Configuration

    Web Configurator with EEC 1 Chapter 16 Initial Configuration This chapter covers the basic configuration needed to set up and use the line card. Refer to the other parts for details about individual fields within screens. 16.1 Initial Configuration Overview This chapter describes the procedure for the initial configuration of the ADSL line card when used with the Ethernet Extension Card (EEC).

  • Page 134: Vlan Setup

    Web Configurator with EEC 1 Specify the name for the profile. Step 3. Configure the upstream and downstream maximum and minimum rates, and the maximum, minimum Step 4. and target signal to noise margins. Click the Add button in the Profile Setup screen. Step 5.

  • Page 135: Management Vlan Setup

    Web Configurator with EEC 1 16.4.2 Management VLAN Setup Procedure: To configure the management VLAN, click the VLAN Setup link on the navigation panel. Step 1. Select an index number in the Static VLAN Setup screen to open the Add VLAN Static Entry screen. Step 2.

  • Page 137: Getting Started Screens

    Web Configurator with EEC 1 Chapter 17 Getting Started Screens This chapter explains the General Setup and Bridge Setup screens. 17.1 Getting Started Overview The web configurator allows you to configure basic settings using the Getting Started screens. 17.2 General Setup Screen Click General Setup in the navigation panel to open this screen.

  • Page 138: Bridge Setup Screen

    Web Configurator with EEC 1 Slot ID The slot ID helps keep track of this individual network module. This field is read only. Apply Click Apply to save your changes back to the line card's volatile memory. The line card loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to the left to save your changes to the non-volatile memory when you are done configuring.

  • Page 139: Table 17-2 Bridge Setup

    Web Configurator with EEC 1 Table 17-2 Bridge Setup LABEL DESCRIPTION Global Setting Bridge Mode Choose Normal or Fast from the drop-down list box. The Normal mode supports 802.1Q tagged VLAN (enabled in VLAN Setup), which allows tagged/untagged frames to and from all ports.

  • Page 140: Figure 17-3 Bridge Ether Type Filter Setup

    Web Configurator with EEC 1 Figure 17-3 Bridge Ether Type Filter Setup The following table describes this screen. 17-4 Getting Started Screens...

  • Page 141: Table 17-3 Bridge Ether Type Filter Setup

    Web Configurator with EEC 1 Table 17-3 Bridge Ether Type Filter Setup LABEL DESCRIPTION Bridge Setup Click this link to go to the Bridge Setup screen. Port Click an entry to go to a screen to edit the egress ports for that port. Ethernet Filter Type Choose Any or IP or PPPoE from the drop-down list.

  • Page 142: Figure 17-4 Bridge Port Filter Setup

    Web Configurator with EEC 1 Figure 17-4 Bridge Port Filter Setup The following table describes this screen. Table 17-4 Bridge Port Filter Setup LABEL DESCRIPTION Bridge Setup Click this link to go to the Bridge Setup screen. Port Click an entry to go to a screen to edit the egress ports for that port. 17-6 Getting Started Screens...

  • Page 143: Figure 17-5 Edit Bridge Port Filter Setup

    Web Configurator with EEC 1 Table 17-4 Bridge Port Filter Setup LABEL DESCRIPTION Egress Port This field displays the forwarding ports for this port. Edit Bridge Port Filter Setup Screen Click a port link in the Bridge Port Filter Setup screen to open this screen. Figure 17-5 Edit Bridge Port Filter Setup The following table describes this screen.
  • Page 144 Web Configurator with EEC 1 Table 17-5 Edit Bridge Port Filter Setup LABEL DESCRIPTION ADSL1-ADSLn Select one or more of these check boxes in order to forward packets to specific ADSL ports. Apply Click Apply to save your changes back to the line card's volatile memory. The line card loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to the left to save your changes to the non-volatile memory when you are done configuring.

  • Page 145: Figure 17-6 Bridge Fast Mode Vlan Id Setup

    Web Configurator with EEC 1 Figure 17-6 Bridge Fast Mode VLAN ID Setup The following table describes this screen. Getting Started Screens 17-9...

  • Page 146: Table 17-6 Bridge Fast Mode Vlan Id Setup

    Web Configurator with EEC 1 Table 17-6 Bridge Fast Mode VLAN ID Setup LABEL DESCRIPTION Bridge Setup Click this link to go to the Bridge Setup screen. Port This is the port's name. VLAN ID Enter a VLAN ID number for the port. Apply Click Apply to save your changes back to the line card's volatile memory.

  • Page 147: Figure 17-7 Bridge Mac Filter Setup

    Web Configurator with EEC 1 Figure 17-7 Bridge MAC Filter Setup The following table describes this screen. Table 17-7 Bridge MAC Filter Setup LABEL DESCRIPTION Bridge Setup Click this link to go to the Bridge Setup screen. Port Click the port name to edit that port’s MAC filter setup. Filtering Enabled This field tells whether or not filtering has been enabled for that port.

  • Page 148: Figure 17-8 Edit Bridge Mac Filter Setup

    Web Configurator with EEC 1 Edit Bridge MAC Filter Setup Screen Click on a port link in the Bridge MAC Filter Setup screen to open this screen. Figure 17-8 Edit Bridge MAC Filter Setup The following table describes this screen. Table 17-8 Edit Bridge MAC Filter Setup LABEL DESCRIPTION...
  • Page 149 Web Configurator with EEC 1 Table 17-8 Edit Bridge MAC Filter Setup LABEL DESCRIPTION Apply Click Apply to save your changes back to the line card's volatile memory. The line card loses these changes if it is turned off or loses power, so use the Config Save link on the navigation panel to the left to save your changes to the non-volatile memory when you are done configuring.

  • Page 150: Figure 17-9 Bridge Mac History

    Web Configurator with EEC 1 Figure 17-9 Bridge MAC History The following table describes this screen. Table 17-9 Bridge MAC History LABEL DESCRIPTION Bridge Setup Click this link to go to the Bridge Setup screen. Refresh Click this button to update the MAC address listings. Flush Ethernet Click this button to clear the MAC address listings for the Ethernet port.

  • Page 151: Figure 17-10 Bridge Port Multicast Filter Record

    Web Configurator with EEC 1 Table 17-9 Bridge MAC History LABEL DESCRIPTION Flush ADSL1~n Click this button to clear the MAC address listings for xDSL ports 1-n. Where n is the maximum port number. 17.3.6 Multicast Filter Record Screen Click Multicast Filter Record in the Bridge Setup screen to open this screen. Figure 17-10 Bridge Port Multicast Filter Record The following table describes this screen.

  • Page 152: Ip Setup Screen

    Web Configurator with EEC 1 17.4 IP Setup Screen The line card needs an IP address for it to be managed over the network. The factory default IP address is 192.168.1.1. The subnet mask specifies the network number portion of an IP address. The factory default subnet mask is 255.255.255.0.

  • Page 153: Chapter 18 Port Setup

    Web Configurator with EEC 1 Chapter 18 Port Setup This chapter explains how to configure individual ports on the line card. 18.1 Port Setup Overview The web configurator allows you to configure settings for the ADSL line. 18.2 LLC Bridge LLC Bridge is a type of encapsulation where one VC (Virtual Circuit) carries multiple protocols with protocol identifying information being contained in each packet header.

  • Page 154: Line Card Port Setup Screen

    Web Configurator with EEC 1 Downstream ADSL settings: Target Signal/Noise Ratio: 6 db Maximum Signal/Noise Ratio: 31 db Minimum Signal/Noise Ratio: 0 db Minimum Transmission Rate: 32 Kbps Maximum Transmission Rate: 2048 Kbps Upstream ADSL settings: Target Signal/Noise Ratio: 6 db Maximum Signal/Noise Ratio: 31 db Minimum Signal/Noise Ratio: 0 db Minimum Transmission Rate: 32 Kbps...

  • Page 155: Figure 18-1 Line Card Port Setup

    Web Configurator with EEC 1 Figure 18-1 Line Card Port Setup The following table describes this screen. Table 18-1 Line Card Port Setup LABEL DESCRIPTION Ethernet Port This field shows the port's name "Ethernet". Enable This field shows whether or not this port is enabled (the Ethernet port is always enabled). Auto This field shows whether auto-negotiation is turned on (Yes) or not (No).

  • Page 156: Figure 18-2 Ethernet Port Setup

    Web Configurator with EEC 1 Table 18-1 Line Card Port Setup LABEL DESCRIPTION Duplex The duplex mode can be half (meaning traffic is transmitted in one direction at a time) or full (meaning traffic is simultaneously transmitted in both directions). PVID This is the VLAN ID that the line card assigns to untagged packets that come in through this port.

  • Page 157: Figure 18-3 Adsl Port Setup

    Web Configurator with EEC 1 Table 18-2 Ethernet Port Setup LABEL DESCRIPTION Port Setup Click this link to go to the Port Setup screen. Speed Use the drop-down list box to select a speed and duplex setting for the Ethernet port. In 10/100Mbps Fast Ethernet, the speed can be 10Mbps or 100Mbps.

  • Page 158: Table 18-3 Adsl Port Setup

    Web Configurator with EEC 1 Table 18-3 ADSL Port Setup LABEL DESCRIPTION Port Setup Click this link to go to the Port Setup screen. Profile Setup Click this link to go to the Profile Setup screen. Enable Select this check box to turn on this ADSL port. The ADSL ports are disabled by default because an enabled but disconnected ADSL port generates more heat than an operating port.

  • Page 159: Figure 18-4 Profile Setting

    Web Configurator with EEC 1 Figure 18-4 Profile Setting The following table describes this screen. Table 18-4 Profile Setting LABEL DESCRIPTION Port Setup This is the card’s slot number. ADSL1 Setup Click this link to go to the port’s setup screen. Profile This is the name of an individual profile.
  • Page 160 Web Configurator with EEC 1 Table 18-4 Profile Setting Basic Profile Setting Upstream Max Rate: Kbps This is the maximum upstream transfer rate for this port. Speeds from 32 to 1024 kilobits per second (Kbps) are supported. Downstream Max Rate: This is the maximum downstream transfer rate for this port.

  • Page 161: Web Configurator With Eec 2

    Web Configurator with EEC 2 Part IV: Web Configurator with EEC 2 This part describes the Advanced Applications and Advanced Management web configurator screens when you use the ADSL line card with the Ethernet extension card.

  • Page 162: Static Route

    Web Configurator with EEC 2 Chapter 18 Static Route This chapter explains how to configure static routes for the line card. 18.1 Static Route Overview The web configurator allows you to set up static routes that tell the line card how to forward management traffic when you configure the TCP/IP parameters manually.

  • Page 163: Figure 18-2 Edit Static Route

    Web Configurator with EEC 2 Table 18-1 Static Route Setup LABEL DESCRIPTION Destination This field displays the IP network address of the final destination. Address Subnet Mask This field displays the subnet mask for this destination. Gateway This field displays the IP address of the gateway. The gateway is an immediate neighbor of your Address line card that will forward the packet to the destination.
  • Page 164 Web Configurator with EEC 2 Table 18-2 Edit Static Route LABEL DESCRIPTION Destination IP This parameter specifies the IP network address of the final destination. Routing is always Address based on network number. If you need to specify a route to a single host, use a subnet mask of 255.255.255.255 in the subnet mask field to force the network number to be identical to the host ID.

  • Page 166: Chapter 19 Vlan

    Web Configurator with EEC 2 Chapter 19 VLAN This chapter explains how to configure VLANs on the line card. 19.1 VLAN Overview A VLAN (Virtual Local Area Network) allows a physical network to be partitioned into multiple logical networks. Stations on a logical network belong to one group. A station can belong to more than one group. With VLAN, a station cannot directly talk to or hear from stations that are not in the same group(s);...

  • Page 167: Forwarding Tagged And Untagged Frames

    Web Configurator with EEC 2 19.3 Forwarding Tagged and Untagged Frames Each port on the switch is capable of receiving tagged or untagged frames. You can configure a card to receive only tagged or all frames on a port-by-port basis. If it is set to tagged-only on a port, then only tagged frames are allowed to enter from that port and untagged frames are dropped;...

  • Page 168: Vlan Setup

    Web Configurator with EEC 2 Table 19-1 GARP Terminology VLAN Type Permanent VLAN This is a static VLAN created manually. Dynamic VLAN This is a VLAN configured by a GVRP registration/deregistration process. VLAN Registration Fixed Fixed registration ports are permanent VLAN members. Administrative Registration Ports with registration forbidden are not allowed to register (join) this...

  • Page 169: Figure 19-1 Static Vlan Setup

    Web Configurator with EEC 2 Figure 19-1 Static VLAN Setup The following table describes this screen. Table 19-2 Static VLAN Setup LABEL DESCRIPTION VLAN Enable Select this check box to enable the VLAN and permit VLANs groups beyond the local switch. CPU VLAN ID The CPU VLAN ID is the number of the VLAN through which you manage the line card.
  • Page 170 Web Configurator with EEC 2 Table 19-2 Static VLAN Setup LABEL DESCRIPTION Untagged Port Untagged ports that have been added to this VLAN are listed here in numerical order, separated by commas. A "-" means no untagged ports are configured. Apply Click Apply to save your changes back to the line card's volatile memory.

  • Page 171: Figure 19-2 Edit 802.1Q Vlan Static Entry

    Web Configurator with EEC 2 Figure 19-2 Edit 802.1Q VLAN Static Entry The following table describes this screen. 19-6 VLAN...

  • Page 172: Table 19-3 Edit 802.1Q Vlan Static Entry

    Web Configurator with EEC 2 Table 19-3 Edit 802.1Q VLAN Static Entry LABEL DESCRIPTION 802.1Q VLAN Click this link to go to the Static VLAN Setup page. Static Entry Setup VLAN ID This is the ID number of VLAN group index number you clicked in the Static VLAN Setup page.

  • Page 174: Chapter 20 Snmp

    Web Configurator with EEC 2 Chapter 20 SNMP This chapter explains how to configure Simple Network Management Protocol (SNMP). 20.1 SNMP General Commands Overview Table 20-1 SNMP COMMAND DESCRIPTION Allows the manager to retrieve an object variable from the agent. GetNext Allows the manager to retrieve the next object variable from a table or list within an agent.

  • Page 175: Figure 20-1 Snmp Setup

    Web Configurator with EEC 2 Figure 20-1 SNMP Setup The following table describes this screen. Table 20-2 SNMP Setup LABEL DESCRIPTION Index This read-only field displays the SNMP index number. Click the index number to go to the "Edit SNMP Setup" menu. Trust Host The trusted host, your line card will only respond to SNMP messages from this address.

  • Page 176: Figure 20-2 Edit Snmp Setup

    Web Configurator with EEC 2 Figure 20-2 Edit SNMP Setup The following table describes this screen. Table 20-3 Edit SNMP Setup LABEL DESCRIPTION SNMP Setup Click this link to go to the SNMP Setup page. Delete Select this check box to delete this set of SNMP access parameters. Trusted Host If you enter a trusted host, your line card will only respond to SNMP messages from this address.

  • Page 177: Chapter 21 Logins

    Web Configurator with EEC 2 Chapter 21 Logins This chapter explains how to change the line card’s passwords. 21.1 Logins Overview The Logins screen allows you to configure the administrator password. 21.2 Logins Screen Click Logins in the navigation panel to open the Logins screen. Use the Logins screen to set administrator passwords for the line card.
  • Page 178 Web Configurator with EEC 2 Table 21-1 Logins LABEL DESCRIPTION Apply Click Apply to save your changes back to the line card's volatile memory. The line card loses these changes if it is turned off or loses power, so use the Config Save link in the navigation panel on the left to save your changes to the non-volatile memory when you are done configuring.

  • Page 179: Chapter 22 Maintenance

    Web Configurator with EEC 2 Chapter 22 Maintenance This chapter explains how to use the maintenance screens to set the Unix syslog parameters, time and date and remote management; as well as perform firmware and configuration file maintenance. 22.1 Maintenance Overview The Maintenance screen allows you to set UNIX syslog parameters and the time and date.
  • Page 180 Web Configurator with EEC 2 Table 22-1 Maintenance LABEL DESCRIPTION Backup Use the Backup link to save your current configuration to a computer. UNIX Syslog Select this check box to activate syslog (UNIX system logging) and then configure the UNIX syslog parameters described in the following fields. Syslog Server IP Enter the IP address of the syslog server.

  • Page 181: Figure 22-1 Maintenance

    Web Configurator with EEC 2 Figure 22-2 Secured Client Setup The following table describes this screen. Table 22-2 Secured Client Setup LABEL DESCRIPTION Maintenance Click Maintenance to return to the main maintenance screen. Secured Select this check box to allow these secured clients to manage the line card. Do not select Enable this check box unless the IP address that you are using to manage the line card is already configured as one of the client addresses below.

  • Page 182: Figure 22-3 Edit Secured Client

    Web Configurator with EEC 2 Figure 22-3 Edit Secured Client The following table describes this screen. Table 22-3 Edit Secured Client LABEL DESCRIPTION Maintenance Click this link to go to the Maintenance screen. Secured Click this link to go to the Secured Client Setup screen. Client Setup Delete Select this check box to remove this client from the list of secured clients.

  • Page 183: Figure 22-4 Firmware Upgrade

    Web Configurator with EEC 2 The card automatically restarts when the upgrade process is complete. Procedure to upgrade your firmware: Use the card’s Statistics screen to check its current firmware version number. Step 1. Download and unzip the new firmware. Step 2.

  • Page 184: Figure 22-5 Restore Configuration

    Web Configurator with EEC 2 Figure 22-5 Restore Configuration 22.2.4 Configuration Backup Screen Click Maintenance in the navigation panel and then Backup to open the Configuration Backup screen. Use the Configuration Backup screen to save the current configuration of the line card to a computer. Click Maintenance to return to the main maintenance screen.

  • Page 185: Chapter 23 Statistics

    Web Configurator with EEC 2 Chapter 23 Statistics This chapter explains the Advanced Management Statistics screens. 23.1 Statistics Overview The web configurator provides statistics screens to allow you to see how much traffic the line card is handling and how it is handling it. 23.2 Statistics Screen Click Statistics in the navigation panel to open this screen.

  • Page 186: Figure 23-2 Show Statistics Screen

    Web Configurator with EEC 2 Table 23-1 Statistics LABEL DESCRIPTION ADSL Driver/ This field displays the version of ADSL driver and modem code. Modem Code Conversion Show Statistics Click here to display ports, temperature and CPU usage statistics. VLAN Status Click here to display 802.1Q VLAN statistics.
  • Page 187 Web Configurator with EEC 2 Table 23-2 Show Statistics Screen LABEL DESCRIPTION Port This refers to the DSL port number or the Ethernet port (labeled LAN). State This field displays "Disable" when the port is turned off or "Down" when the port is turned on, but not connected.

  • Page 188: Figure 23-3 Vlan Status

    Web Configurator with EEC 2 Figure 23-3 VLAN Status The following table describes this screen. Table 23-3 VLAN Status LABEL DESCRIPTION Index This is the VLAN index number. This is the VLAN ID number configured in the Edit Static VLAN page. Egress Port Ports that have been added to this VLAN are listed here in numerical order, separated by commas.

  • Page 189: Chapter 24 Diagnostic

    Web Configurator with EEC 2 Chapter 24 Diagnostic This chapter explains the Advanced Management Diagnostic screens. 24.1 Diagnostic Overview The line card provides diagnostic screens to aid in troubleshooting. 24.2 Line Card Diagnostic Screen Click Diagnostic in the navigation panel to open the General Diagnostics screen. Use this screen to check system logs, reset the system or ping IP addresses.

  • Page 190: Reset System

    Web Configurator with EEC 2 Table 24-1 General Diagnostic LABEL DESCRIPTION Clear Error Log Click this button to clear the log of events in the multi-line text box. IP Address Type the IP address of a device that you want to ping in order to test a connection. Ping Click this button to have the line card ping the IP address (in the field to the left) 5 times.

  • Page 191: Chapter 25 Troubleshooting

    Web Configurator with EEC 2 Chapter 25 Troubleshooting This chapter covers potential problems and possible remedies. After each problem description, some steps are provided to help you to diagnose and to solve the problem. 25.1 DSL LED(s) A DSL LED is not on. Table 25-1 Troubleshooting the DSL LED(s) STEPS CORRECTIVE ACTION...

  • Page 192: Dsl Led(S) Turn On And Off

    Web Configurator with EEC 2 25.3 DSL LED(s) Turn On and Off A DSL LED turns on and off intermittently. Table 25-3 Troubleshooting a Non-Constant DSL LED STEPS CORRECTIVE ACTION Check the line card’s diagnostic screen. Connect a DSL modem directly to the DSL port of the line card using a different telephone wire. If the DSL LED still turns on and off repeatedly, contact the distributor.

  • Page 193: Snmp

    Web Configurator with EEC 2 Table 25-7 Troubleshooting a Local Server STEPS CORRECTIVE ACTION Refer to section 25.2 to make sure that the subscriber is able to transmit to the line card. Make sure the computer behind the DSL device has the correct gateway IP address configured. Check the line card’s VLAN configuration (see the VLAN chapter).

  • Page 195: Commands With Msc

    Commands with MSC Part V: Commands with MSC This part gives information on commands to use and how to use the web configurator to configure and manage the ADSL line card with the Management Switch Card.

  • Page 197: Chapter 27 Commands With Msc

    Commands with MSC Chapter 27 Commands with MSC This chapter introduces the command line interface and lists all of the commands that are available when you use the line card with the management switch card. 27.1 Command Line Interface with MSC Overview You can use text command lines for software configuration.

  • Page 198: Commands With Msc

    Commands with MSC 27.2 Commands with MSC The following table lists all of the commands that you can use with the line card when you use the management switch card. Refer to the chapters on commands with the Ethernet extension card for descriptions of commonly used commands.
  • Page 199 Commands with MSC Table 27-1 Commands with MSC COMMANDS DESCRIPTION profile list [<"*dsl"> Shows profile contents. [<profile_name>]] profile map <"*dsl"> Displays a profile’s port mapping. <prof_name> set <slot-port- Creates or modifies a PVC setting. vpi/vci> <...> pvc delete <slot-port- Removes a PVC setting. vpi/vci>...
  • Page 200 Commands with MSC Table 27-1 Commands with MSC COMMANDS DESCRIPTION stat ch <port> <vpi> <vci> Displays channel status of all DSL lines. stat chs <port> Displays channel status of a DSL line. linedata <port> Displays the line data load per symbol (tone). linerate <port>...

  • Page 201: Chapter 28 Command Examples

    Commands with MSC Chapter 28 Command Examples This chapter gives some command examples 28.1 Command Examples Overview These are commands that you may use frequently in configuring and maintaining your line cards. 28.2 Sys Commands Theses are the commonly used commands that belong to the sys (system) group of commands. 28.2.1 Log Disp Command Syntax:...

  • Page 202: Lcman Commands

    Commands with MSC 28.2.3 Version Command Syntax: sys version This command shows the RAS code, firmware version, system uptime and bootbase version. An example is shown next. ras> sys version ZyNOS version: V3.50(DS.4)b16 | 01/30/2003 romRasSize: 1638380 system up time: 29:15:35 (a0baac ticks) bootbase version: V1.02(MSC1000) | 09/26/2002 Figure 28-2 Version Command Example...

  • Page 203: Figure 28-4 Lcman Port List Command

    Commands with MSC An example is shown next. ras> lcman port list 2 slot-port status type mode profile --------- -------- ---------- ------ --------- disable adsl_anxa auto DEFVAL disable adsl_anxa auto DEFVAL disable adsl_anxa auto DEFVAL disable adsl_anxa auto DEFVAL disable adsl_anxa auto DEFVAL disable...

  • Page 204: Figure 28-5 Lcman Command Command Example

    Commands with MSC ras> lcman command 3 lineperf 2 Current line performance counters: nfebe-I/nfebe-ni : 0/0 ncrc-I/ncrc-ni : 0/0 nfecc-I/nfecc-ni : 0/0 nfec-I/nfec-ni : 0/0 nblks-ds/nblks-us : 0/0 nsec-ds/nsec-us : 0/0 n-eb-ds/n-eb-us : 0/0 n-bbe-ds/n-bbe-us : 0/0 n-es-ds/n-es-us : 0/0 n-ses-ds/n-ses-us : 0/0 non-ses-blks-ds/non-ses-blks-us : 0/0...

  • Page 205: Figure 28-7 Lcman Maccount Active Command

    Commands with MSC ras> lcman maccount active 2 ras> lcman maccount list slot maccount status ==== ======== ======== active inactive inactive inactive inactive ras> Figure 28-7 Lcman Maccount Active Command 28.3.6 Lcman Status Command Syntax: lcman status This command shows information about the line card manager. This information includes how many slots are under management, the slot mask and the type of line card it is managing in each slot (if any), as well as the line card’s IP address and driver version.

  • Page 207: Web Configurator With Msc

    Web Configurator with MSC Part VI: Web Configurator with MSC This part gives information on commands to use and how to use the web configurator to configure and manage the ADSL line card with the management switch card.

  • Page 209: Web Configurator With Msc Introduction

    Web Configurator with MSC Chapter 28 Web Configurator with MSC Introduction This chapter tells how to access and navigate the web configurator when you use the ADSL line card with the management switch card. 28.1 Web Configurator with MSC Overview The web configurator allows you to use a web browser to manage the ADSL line card while it is behind the management switch card.

  • Page 210: Home Screen

    Web Configurator with MSC 28.2.2 Change Password This screen prompts you to change your password if it is still set to the default. Figure 28-2 Change Password Screen 28.3 Home Screen Navigation Panel Figure 28-3 Home Screen This is the web configurator’s home screen. Click a link on the navigation panel to go to the corresponding screen. The following table lists the links that you use to configure or monitor the line card.

  • Page 211: Screens Overview

    Web Configurator with MSC Table 28-1 Navigation Panel Links LABEL DESCRIPTION Getting Started Port Setup This link takes you to screens where you can configure settings for the line card’s individual DSL ports. Advanced Applications VLAN Setup This link takes you to screens where you can configure VLANs for the line card. Advanced Management Maintenance This link takes you to a screen where you can perform firmware file maintenance on the line...

  • Page 212: Navigating The Web Configurator

    Web Configurator with MSC 28.6 Navigating the Web Configurator The web configurator uses multiple levels. You only need to use one level for features that deal with the IES-2000 or IES-3000 as a whole. For example, to configure General Setup, click the link on the navigation panel to open the configuration screen.

  • Page 213: Figure 28-5 Alc Port Setup Screen

    Web Configurator with MSC Figure 28-5 ALC Port Setup Screen Click a link labeled Up to go to a screen on the next higher level. For example, click Up in the ALC Edit Port Setup screen (see Figure 28-6) to go to the ALC Port Setup screen (see Figure 28-5). Web Configurator with MSC Introduction 28-5...

  • Page 214: Figure 28-6 Alc Edit Port Setup Screen

    Web Configurator with MSC Figure 28-6 ALC Edit Port Setup Screen 28-6 Web Configurator with MSC Introduction...

  • Page 215: Chapter 29 Adsl Port Setup

    8160 Kbps 1024 Kbps G.lite 1536 Kbps 512 Kbps ANSI T1.413 issue 2 (ALC1024-61) 8160 Kbps 1024 Kbps Downstream and Upstream 27.3 Downstream refers to traffic going out from the line card to the subscriber’s ADSL modem or router. Upstream refers to traffic coming into the line card from the subscriber’s ADSL modem or router.

  • Page 216: Interleave Delay

    G.dmt standard. Configure a profile with a maximum downstream rate of 1536 Kbps or less for use with G.lite. Refer to the ALC1024 Overview chapter for the settings of the default profile and ADSL port default settings. 29.7 ALC Port Setup Screen Click Port Setup in the navigation panel to open the Port Setup screen.

  • Page 217: Figure 29-1 Alc Port Setup Screen

    Web Configurator with MSC This screen is a summary screen that displays read-only information about the DSL ports. Click a port's index number to go to a setup screen for that port. Figure 29-1 ALC Port Setup Screen Table 29-2 ALC Port Setup LABEL DESCRIPTION Slot (N) Port...

  • Page 218: Figure 29-2 Alc Profile Setup Screen

    Web Configurator with MSC Table 29-2 ALC Port Setup LABEL DESCRIPTION Mode This field shows which ADSL operational mode the port is set to use. Upstream Rate This field shows the maximum upstream speed that is configured for this port. (Kbps) Downstream This field shows the maximum downstream speed that is configured for this port.

  • Page 219: Figure 29-3 Alc Edit Profile Screen

    Web Configurator with MSC Table 29-3 ALC Profile Setup LABEL DESCRIPTION Latency Mode This is the ADSL latency mode (fast or interleave) for the ports that belong to this profile. Upstream Max Rate: Kbps This is the maximum upstream transfer rate for the ports that belong to this profile. Speeds from 32 to 1024 kilobits per second (Kbps) are supported.

  • Page 220: Table 29-4 Alc Edit Profile

    Web Configurator with MSC Table 29-4 ALC Edit Profile LABEL DESCRIPTION Slot (N) Edit Profile This is the card’s slot number. Click this link to go to the card's Profile Setup screen. Profile Name When editing a profile, this is the name of this profile. When adding a profile, type a name for the profile.

  • Page 221: Figure 29-4 Alc Edit Port Setup Screen

    Web Configurator with MSC Table 29-4 ALC Edit Profile LABEL DESCRIPTION Latency Delay(ms) Configure this field when you set the Latency Mode field to interleave. Type the number of milliseconds (1-255) of interleave delay to use for upstream transfers. It is recommended that you configure the same latency delay for both upstream and downstream.

  • Page 222: Channels

    Web Configurator with MSC Table 29-5 ALC Edit Port Setup LABEL DESCRIPTION Slot (N) Edit Port Setup This is the card’s slot number. Channel Setup Click this link to go to the port's Channel Setup screen. Click this link to go to the card's Port Setup screen. Active Select this check box to turn on this ADSL port.

  • Page 223: Alc Port Channel Setup Screen

    Web Configurator with MSC Assign the channel a high IEEE 802.1p priority. 29.8.1 LLC is a type of encapsulation where one VC (Virtual Circuit) carries multiple protocols with each packet header containing protocol identifying information. Despite the extra bandwidth and processing overhead, this method may be advantageous if it is not practical to have a separate VC for each carried protocol, for example, if charging heavily depends on the number of simultaneous VCs.
  • Page 224 Web Configurator with MSC Table 29-6 ALC Port Channel Setup LABEL DESCRIPTION Slot (N) Channel Setup This is the card’s slot number. Click this link to go to the card's Edit Port Setup screen. VPI/VCI This field displays the Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI). The VPI and VCI identify a channel on this port.

  • Page 225: Figure 29-6 Alc Edit Port Channel Setup Screen

    Web Configurator with MSC Figure 29-6 ALC Edit Port Channel Setup Screen Table 29-7 ALC Edit Port Channel Setup LABEL DESCRIPTION Slot (N) Add Channel This is the card’s slot number. Setup Click this link to go to the port's Channel Setup screen. Type the Virtual Path Identifier for this port.

  • Page 227: Chapter 30 Ieee 802.1Q Vlan

    Web Configurator with MSC Chapter 30 IEEE 802.1Q VLAN This chapter explains how to configure IEEE 802.1Q VLANs on the ADSL line card. 30.1 IEEE 802.1Q VLAN Overview Use the web configurator to configure an IEEE 802.1Q Tagged VLAN (Virtual Local Area Network) to partition a physical network into multiple logical networks.

  • Page 228: Alc Static Vlan Entry Add Or Edit Screen

    Web Configurator with MSC Table 30-1 ALC Static VLAN Setup LABEL DESCRIPTION Active This field displays whether the VLAN is currently enabled Yes or disabled No. Click this button to add a new VLAN ID. Delete Select a channel’s Delete check box and click the Delete button to remove the channel. 30.3 ALC Static VLAN Entry Add or Edit Screen Click VLAN Setup in the navigation panel and then a card’s link in the VLAN Setup screen.

  • Page 229: Alc Management Vlan Edit Screen

    Web Configurator with MSC Table 30-2 ALC Edit Static VLAN LABEL DESCRIPTION Slot (N) Edit VLAN This is the card’s slot number. Static Entry Click this link to go to the Static VLAN Setup screen. VLAN ID This is the number that identifies the VLAN group. When you add a static VLAN, type a number (1-4094) to identify the VLAN.

  • Page 230: Figure 30-3 Alc Management Vlan Edit Screen

    Web Configurator with MSC Figure 30-3 ALC Management VLAN Edit Screen Table 30-3 ALC Management VLAN Edit LABEL DESCRIPTION Slot (N) Edit VLAN This is the card’s slot number. Static Entry Click this link to go to the Static VLAN Setup screen. VLAN ID This is the number that identifies the VLAN group.

  • Page 231: Chapter 31 Maintenance

    Web Configurator with MSC Chapter 31 Maintenance This chapter explains how to use the ADSL line card’s maintenance screen. 31.1 Maintenance Overview The web configurator allows you to upload new firmware to the ADSL line card. 31.1.1 Firmware Upgrade Screen Click Maintenance in the navigation panel and then Firmware Upgrade in the Maintenance screen.

  • Page 233: Chapter 32 Statistics

    Web Configurator with MSC Chapter 32 Statistics This chapter explains the ADSL line card’s Advanced Management Statistics screens. 32.1 Statistics Overview The web configurator provides statistics screens to allow you to see how much traffic the ADSL line card is handling and how it is handling it.

  • Page 234: Figure 32-2 Alc Hardware Monitor Screen

    Web Configurator with MSC Table 32-1 ALC Statistics LABEL DESCRIPTION Port Statistics Click this button to display statistics for the ports on this card. Channel Statistics Click this button to display statistics for the channels on this card’s ports. Vlan Status Click this button to display IEEE 802.1Q VLAN statistics for this card.
  • Page 235 Web Configurator with MSC Table 32-2 ALC Hardware Monitor LABEL DESCRIPTION Current This shows the current temperature at this sensor. Max This field displays the maximum temperature measured at this sensor. Min This field displays the minimum temperature measured at this sensor. Threshold This field displays the upper temperature limit at this sensor.

  • Page 236: Figure 32-3 Alc Port Statistics Screen

    Web Configurator with MSC Figure 32-3 ALC Port Statistics Screen Table 32-3 ALC Port Statistics LABEL DESCRIPTION System This field shows how long the system has been running since the last time it was started. Uptime Port This refers to the DSL port number. Link This field shows the upstream/downstream speeds of the DSL connections that are up or Down for the DSL ports that are not connected.
  • Page 237 Web Configurator with MSC Table 32-3 ALC Port Statistics LABEL DESCRIPTION Errors This field shows the number of received errors on this port. Tx KB/s This field shows the number of kilobytes transmitted on a per-second basis by this port. Rx KB/s This field shows the number of kilobytes received on a per-second basis by this port.

  • Page 238: Figure 32-4 Alc Channel Statistics Screen

    Web Configurator with MSC Figure 32-4 ALC Channel Statistics Screen Table 32-4 ALC Channel Statistics LABEL DESCRIPTION System This field shows how long the system has been running since the last time it was started. Uptime Port This refers to the DSL port number. This field displays the channel’s Virtual Path Identifier (VPI).
  • Page 239 Web Configurator with MSC Table 32-4 ALC Channel Statistics LABEL DESCRIPTION RxPkts This field shows the number of packets received by this port on this individual channel. Errors This field shows the number of received errors on this port on this individual channel. Tx B/s This field shows the number of bytes transmitted on a per-second basis by this port on this individual channel.

  • Page 240: Figure 32-5 Alc 802.1Q Vlan Status Screen

    Web Configurator with MSC Figure 32-5 ALC 802.1Q VLAN Status Screen Table 32-5 ALC 802.1Q VLAN Status LABEL DESCRIPTION Index This is the VLAN index number. This is the VLAN identification number that was configured in the VLAN ALC Setup screen. Egress Port Ports that have been added to this VLAN are listed here in numerical order.
  • Page 241 Web Configurator with MSC Table 32-5 ALC 802.1Q VLAN Status LABEL DESCRIPTION Next Page Click Next Page to show the subsequent screen of VLAN status information (if there is more than one screen of VLAN statistics). Statistics 32-9...

  • Page 243: Chapter 33 Diagnostics

    Web Configurator with MSC Chapter 33 Diagnostics This chapter explains the ADSL line card’s Diagnostic screen. 33.1 Diagnostic Overview The ADSL line card’s diagnostic screen aids in troubleshooting. 33.2 Diagnostic Screen Click Diagnostic in the navigation panel and then the line card’s link in the Diagnostic screen to open the ALC Diagnostic screen.

  • Page 244: Figure 33-2 Alc Diagnostic Dsl Screen

    Web Configurator with MSC Table 33-1 Diagnostic LABEL DESCRIPTION Click this to go to the DSL Diagnostic screen Diagnostic Click this link to go to the first diagnostic screen. Error Log Click this button to display a log of events in the multi-line text box. System Click this button to restart the card.
  • Page 245 Web Configurator with MSC Table 33-2 ALC Diagnostic DSL LABEL DESCRIPTION Click this link to go to the card’s Diagnostic screen. Port This refers to the DSL port number. Local Loopback Click this to perform a local loopback test on the specified G.SHDSL port. A local loopback test is used to check the device's DSL chip.

  • Page 247: Troubleshooting With Msc

    Web Configurator with MSC Chapter 34 Troubleshooting with MSC This chapter covers potential problems and possible remedies. After each problem description, some steps are provided to help you to diagnose and to solve the problem. 34.1 Troubleshooting Overview See Chapter 25 for additional troubleshooting tips. 34.2 Configured Settings The line card’s configured settings do not take effect.

  • Page 249: Index

    Index Part VII: Index This part provides an index of important terms.
  • Page 251 Default 802.1p Priority ....29-8, 29-10, 29-11 ALC Profile Setup........18-6, 29-4 Default ADSL Settings .......... 1-2 ALC1024..............xix Default Gateway ..........17-16 ALC1024 Overview ........1-1, 2-1 Default IP Address ..........10-2 Annex A ..........xix, 5-5, 5-11 Default Profile Settings.......18-1, 29-2 Annex B ............xix, 5-11 Default Route ............
  • Page 252 ALC1024 User’s Guide DVLAN Getentry Command .......8-11 G.lite........5-1, 5-12, 6-1, 7-1, 29-1 DVLAN List Command ........8-10 GARP ..............8-2 DVLAN Table..........8-1, 8-2 gdmt.............5-11, 5-12 General IP Commands ...... 10-2, 12-1, 12-2 General Setup ............17-1 General Syntax Conventions........xix Emergency Console Port ........13-4 Get Slot Command ..........4-6...
  • Page 253 ALC1024 User’s Guide Lcman Commands ..........28-2 Naming Conventions..........xix Limited Warranty ............. iv Navigating the Web Configurator....15-4, 28-4 line bit allocation............ 5-4 line operating values ..........5-4 line performance counters ........5-5 Online Registration ..........xix line rate parameters ..........5-6 Operational mode........5-11, 5-12...
  • Page 254 ALC1024 User’s Guide Supported Traps ...........11-4 SVLAN CPU Command ........8-6 Saving Configuration ......... 15-4, 28-3 SVLAN Delentry Command ........8-10 Screen Overview ........15-3, 28-3 SVLAN Getentry Command ........8-10 Secured Host SVLAN List Command..........8-6 Default ..............2-3 SVLAN Setentry Command........8-7 Enable/Disable............4-4 SVLAN Table ............8-1 Secured Host Add Command .........4-4...
  • Page 255 ALC1024 User’s Guide File Types............13-3 Explicit Tagging..........8-1 Protocols............13-3 ID (VID)............7-11, 8-2 Timing .............. 13-3 Implicit Tagging..........8-1 Upstream ..........5-1, 29-1, 29-6 Port-Based............7-6 upstream (us)............5-6 Registration Information ........8-1 Upstream Max Rate: Kbps ........29-5 Tags..............

Table of Contents