Bosch GOP 10,8 V-LI Professional Original Instructions Manual page 7

OBJ_BUCH-775-004.book Page 7 Wednesday, February 6, 2013 9:46 AM
16 Felt ring of the dust extraction*
17 Retaining clip of the dust extraction*
18 Vacuum connection*
19 Dust extraction*
20 Vacuum hose*
21 Extraction adapter*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Cordless Multi-Cutter
Article number
Rated voltage
No-load speed n
0
Oscillation angle, left/right
Weight according to
EPTA-Procedure 01/2003
Assembly
Battery Charging
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The Lithium-Ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Removing the battery
To remove the battery 2, press the unlocking buttons 1 and
pull the battery out of the machine to the rear. Do not exert
any force.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
4 indicate the charge condition of the battery 2. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
To indicate the charge condition, press and hold button 3 of
the switched off machine.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
Bosch Power Tools
Changing the Tool
 Before any work on the machine itself (e.g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
 Wear protective gloves when changing application
tools/accessories. Contact with the application tool/ac-
cessoriy can lead to injuries.
Selecting the Application Tool/Accessory
GOP 10,8 V-LI
3 601 H58 0..
V= 10.8
-1
min 5000 –20000
° 1.4
kg 1.0
* Optional accessory; for the complete accessories please see Bosch
accessory programme.
Capacity
Mounting/Replacing the Application Tool/Accessory
2/3
If required, remove an already mounted application tool/
1/3
accessory.
<1/3
For removing the application tool/accessory, loosen the
Reserve
screw 11 with the Allen key 12 and remove the application
tool/accessory.
English | 7
Accessory Material
HCS wood seg- Wooden materials,
ment saw blade* plastic
BIM segment saw Wooden materials,
blade* plastic, non-ferrous
metals
HCS plunge cut Wooden materials,
saw blades, plastic, gypsum and
wood* other soft materials
BIM plunge cut Metal (e.g. unhard-
saw blades, ened nails, screws,
metal* smaller profiles),
non-ferrous metals
BIM plunge cut Wood, metal, non-
saw blade, wood ferrous metals
and metal*
HM-Riff segment Grouting joints,
saw blade* soft wall tiles,
glass-fibre reinforc-
es plastic and other
HM-Riff delta
abrasive materials
plate*
Scraper, rigid* Carpets, coverings
Scraper, flexible* Silicone and other
elastic materials
Base plate for Depends on sand-
sanding, series ing sheet
Delta 93 mm*
1 609 92A 013 | (6.2.13)