Download Table of Contents Print this page

Installation Instructions - KitchenAid KBGS274LSS Installation Instructions And Use And Care Manual

27" (68.6 cm), 36" (91.4 cm) and 39" (99.1 cm) outdoor grills

Advertisement

Table of Contents
Installation
Instructions —
Built-In Outdoor
Grill
(combustible
construction)
WARNING
Fire Hazard
Do not install this grill on or near
combustible materials.
Doing so can result in death or fire.
IMPORTANT: The built-in grill for use in a
combustible enclosure, also includes an
insulated jacket which must be used for
proper installation. See Page 4 for cutout
dimensions.
WARNING
Fire Hazard
Do not use grill near combustible
materials.
Do not store combustible materials
near grill.
Doing so can result in death or fire.
WARNING
Excessive Weight Hazard
Use two or more people to move
and install grill.
Failure to do so can result in back
or other injury.
Natural Gas Use
This installation must conform with local
codes and ordinances**. In the absence of
local codes, installations must conform
with either the National Fuel Gas Code
ANSI Z223.1, or CAN/CGA-B149.1*
Natural Gas and Propane installation code.
6
1.
Place grill and insulated jacket into
the enclosure, but leave enough room
between back of grill and insulated jacket
to connect to gas supply.
WARNING
Explosion Hazard
Securely tighten all gas connections.
If connected to LP, have a qualified
person make sure gas pressure does
not exceed 11" (28 cm) water column.
Examples of a qualified person
include:
licensed heating personnel,
authorized gas company personnel,
and,
authorized service personnel.
Failure to do so can result in death,
explosion, or fire.
2.
Make gas connections.
A combination of pipe fittings must be
used to connect the grill to the existing
gas line.
• If local codes permit, use a flexible
stainless steel tubing gas connector,
design-certified by AGA or CSA
International, to connect the grill to the
rigid gas supply line. 5/8" diameter line is
recommended. Using a wrench to
tighten, connect the gas supply to the
grill. Use pipe joint compound on all non-
flared male threads. Do not kink or
damage the flexible connector when
moving the grill.
• Pipe-joint compounds suitable for use
with L.P. gas must be used. Do not use
Teflon
®
tape.
1/2" grill
rear of
gas pipe
grill
flexible gas
connector
Copies of the standards listed may
be obtained from:
* CSA International
8501 East Pleasant Valley Rd.
Cleveland, Ohio 44131-5575
** for local codes, contact your local
building inspector
3.
Open shutoff valve in the gas
supply line. The valve is open when the
handle is parallel to the gas pipe.
valve open
4.
Test all connections by brushing on
an approved non-corrosive leak-detection
solution. Bubbles will show a leak. Correct
any leak found.
5.
Open the hood.
6.
For models equipped with
rotisserie, remove the rotisserie's skewer
from the grill.
7.
For models with side burners.
Remove side burner cover from the top of
the carton that is located on the grill
grate. Remove bubble wrap from side
burner cover and set aside.
Open carton located on the grill grate.
Remove side burner grate, unwrap and
set aside.
Remove burners and burner caps from
carton and unwrap. Install each set of
burners and caps inside the side burner
cavity as shown.
burner
cap
burner
cover
extension
burner
grate
Install side burner grate and cover (with
extension toward grill) as shown.
Properly dispose of all packing material.
® Teflon is a registered trademark of E.I. Du Pont
de Nemours and Company.
valve closed

Advertisement

Table of Contents
loading

This manual is also suitable for:

Kbgs292lssKbgs364lss

Table of Contents