Assembly And Adjustment; Safety Warnings - Black & Decker KP1200 Instruction Manual

12 • ENGLISH
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
Black & Decker Service Center or an equally
qualified person in order to avoid damage or injury.
If the power cord is replaced by an equally qualified
person, but not authorized by Black & Decker, the
warranty will not be valid.
7. Labels on tool
The label on your tool may include the following
symbols:
Read V ........ Volts
Instructions
A ........ Amperes
Manual
Hz .......Hertz
Use
W ........Watts
Eye
min ..... minutes
Protection
Use
Ear
Protection
n ....... No-Load
0
.... Class II
Construction
.... Earthing
Terminal
.... Safety
Alert
.... Alternating
Symbol
Current
.../min.. Revolutions
.... Direct
or Recipro-
Current
cation per
minute
Speed
ADDITIONAL POWER TOOL

SAFETy WARNINGS

Warning! Additional safety warnings for polisher.
► Hold power tool by insulated gripping surfaces,
because the belt may contact its own cord. Cutting
a "live" wire may make exposed metal parts of the
power tool "live" and shock the operator.
► Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it
unstable and may lead to loss of control.
Warning! Contact with or inhalation of dusts arising
from polishing applications may endanger the health of the
operator and possible bystanders. Wear a dust mask
specifically designed for protection against dust and fumes
and ensure that persons within or entering the work area
are also protected.
► Thoroughly remove all dust after polishing.
► Take special care when sanding paint which is possibly
lead based or when sanding some woods and metal
which may produce toxic dust:
- Do not let children or pregnant women enter
the work area.
- Do not eat, drink or smoke in the work area.
- Dispose of dust particles and any other debris safely.
► This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the appliance.
► The intended use is described in this instruction
manual. The use of any accessory or attachment or
performance of any operation with this tool other than
those recommended in this instruction manual may
present a risk of personal injury and/or damage
to property.
FEATURES(Fig. A and B)
1. Pad
2. Handles
3. On/off switch
4. Cord Set
5. Towel bonnet
6. Polishing bonnet

ASSEMBLy AND ADjUSTMENT

Prior to assembly and adjustment always unplug the tool.
Fitting the towel applicator or wool bonnet (Fig. B)
Place the towel applicator bonnet (5) or wool bonnet
(6) onto the pad (1) as shown. It is recommended to