Yamaha M7CL Owner's Manual page 74

Sending signals from MIX channels to the STEREO/MONO bus
1 Channel select button
This indicates the channel number, the icon selected
for that channel, and the channel name. When you
press this button, that channel will be selected for
operations, and the corresponding [SEL] key will
light.
B
TO ST PAN/BALANCE knob
For monaural MIX channels, this acts as the PAN
knob that adjusts the left/right panning of the signal
sent to the STEREO bus. For stereo MIX channels,
this acts as the BALANCE knob that adjusts the vol-
ume.
To adjust the value, press the knob to select it, and
operate the corresponding multifunction encoder.
If the signal reaches the overload point at any meter
detection point in that channel, the indicator at the
right of the knob will light.
C
ST/MONO indicator
If a MIX channel is set to ST/MONO mode, this indi-
vidually indicates the on/off status of the signal sent
from the channel to the STEREO bus / MONO bus.
If a channel is set to LCR mode, the LCR indicator is
displayed in this location. The LCR indicator indicates
the on/off status of all signals sent from that channel to
the STEREO bus and MONO bus.
3
Access the eight-channel TO STEREO/
MONO popup window.
4
Use the MODE button to select either ST/
MONO mode or LCR mode for each chan-
nel.
5
In the STEREO / MONO MASTER section of
the top panel, make sure that the [ON] key
of the STEREO channel / MONO channel is
turned on, and raise the fader to an appro-
priate position.
6
Press the [MIX 1-8] key or [MIX 9-16] key so
that the MIX channels you want to control
are recalled to the Centralogic section.
7
Make sure that the [ON] key of that channel
is on, and use the fader in the Centralogic
section to raise the master level of the MIX
channel to an appropriate position.
74
M7CL Owner's Manual
The subsequent steps will differ depending on whether
ST/MONO mode or LCR mode was selected for the
channel in step 5.
● Channels for which ST/MONO mode is
selected
8
In the TO STEREO/MONO popup window,
use the STEREO/MONO button to turn the
signal sent from the MIX channel to the
STEREO bus / MONO bus on or off.
For a channel that is set to ST/MONO mode, the sig-
nals sent to the STEREO bus and to the MONO bus
can be switched on/off individually.
9
In the TO STEREO/MONO popup window,
press the TO ST PAN knob to select it, and
use multifunction encoders 1–8 to adjust
the pan of the signal sent from the MIX
channels to the STEREO bus.
● Channels for which LCR mode is
selected
8
Make sure that the LCR button is turned on
in the TO STEREO/MONO popup window.
Channels for which the LCR button is off will not send
any signal to the STEREO bus or MONO bus.
9
In the TO STEREO/MONO popup window,
press the CSR knob to select it, and use
multifunction encoders 1–8 to adjust the
level difference between the signals sent
from that channel to the STEREO (L/R) bus
and to the MONO (C) bus.
The CSR knob settings are the same as for input chan-
nels. (For details, refer to → p. 59)
10
In the TO STEREO/MONO popup window,
press the TO ST PAN knob to select it, and
use multifunction encoders 1–8 to adjust
the panning of the signals sent from the
MIX channel to the STEREO (L/R) bus and
the balance of the signals sent to the
MONO (C) bus and STEREO (L/R) bus.
Refer to page 59 for details on how the signal level
sent from an LCR mode MIX channel to each bus will
change according to the operation of the TO ST PAN
knob.