Page 1: Table Of Contents
Order Number ITD0711079CE High Definition Plasma Display TH-103PF10WK Model No. TH-103PF10TK Model No. TH-103PF10RK Model No. GPF10D Chassis TABLE OF CONTENTS PAGE PAGE 1 Safety Precautions----------------------------------------------- 3 7.5. Removal of HDMI-Board ------------------------------ 28 1.1. General Guidelines---------------------------------------- 3 7.6. Removal of DS-Board ---------------------------------- 28 2 Warning -------------------------------------------------------------- 4 7.7.
Page 2 TH-103PF10WK/TK/RK 7.30. Removal of C5-Board ----------------------------------- 41 10.15. Lead Wiring (7) ------------------------------------------ 104 7.31. Removal of C6-Board ----------------------------------- 42 10.16. Lead Wiring (8) ------------------------------------------ 105 7.32. Removal of C7-Board ----------------------------------- 42 10.17. Lead Wiring (9) ------------------------------------------ 106 7.33. Removal of C8-Board ----------------------------------- 43 11 Exploded View and Replacement Parts List---------- 107 7.34.
Page 3: Safety Precautions
TH-103PF10WK/TK/RK 1 Safety Precautions 1.1. General Guidelines 1. When conducting repairs and servicing, do not attempt to modify the equipment, its parts or its materials. 2. When wiring units (with cables, flexible cables or lead wires) are supplied as repair parts and only one wire or some of the wires have been broken or disconnected, do not attempt to repair or re-wire the units.
Page 4: Warning
TH-103PF10WK/TK/RK 2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensi- tive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec- trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"...
Page 5: About Lead Free Solder (Pbf)
TH-103PF10WK/TK/RK 2.2. About lead free solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).
Page 6: Service Navigation
TH-103PF10WK/TK/RK 3 Service Navigation 3.1. Service Hint...
Page 7 TH-103PF10WK/TK/RK Board Name Function Board Name Function Digital Signal Processor, Data Drive (X) Format Converter, Data Drive (Y) Plasma AI Processor Data Drive (Z) Sub-Field Processor Audio Out Slot Interface (Audio / Video / Sync Input Power Switch Switch), Sustain Out (Upper)
Page 8: Applicable Signals
TH-103PF10WK/TK/RK 3.2. Applicable signals...
Page 9 TH-103PF10WK/TK/RK...
Page 10: Specifications
2,414 mm × 1,421 mm × 129 mm (141 mm when including protruding portion of slots) Mass (weight) approx. 220.0 kg net Notes: • Design and specifications are subject to change without notice. Mass and dimensions shown are approximate. • This equipment complies with standards. AS/NZS60065, CISPRE22 Class-B (TH-103PF10WK)
Page 11: Service Mode
TH-103PF10WK/TK/RK 5 Service Mode 5.1. CAT (Computer Aided Test) mode To exit the CAT mode, access the ID mode and switch off the main power. 5.1.1. IIC mode Select the IIC mode by Up / Down button on the remote control at the front page of CAT mode and then press the Action button on the remote control.
Page 12: Cd Mode
TH-103PF10WK/TK/RK 5.1.2. CD mode Select the CD mode by Up / Down button on the remote control at the front page of CAT mode and then press the Mute button on the remote control more than 3 seconds. Microcomputer software version (IC4002), this version can be upgrade by 1.
Page 13: Ms Mode
TH-103PF10WK/TK/RK 5.1.4. MS mode Select the MS mode by Up / Down button on the remote control at the front page of CAT mode and then press the Mute button on the remote control more than 3 seconds. To exit the MS mode, press the R button on the remote control.
Page 14: Id Mode
TH-103PF10WK/TK/RK 5.1.5. ID mode Select the ID mode by Up / Down button on the remote control at the front page of CAT mode and then press the Mute button on the remote control more than 3 seconds. To exit the ID mode, press the R button on the remote control.
Page 15: Iic Mode Structure (Following Items Value Is Sample Data)
TH-103PF10WK/TK/RK 5.2. IIC mode structure (following items value is sample data)
Page 16: Option Setting
TH-103PF10WK/TK/RK 5.3. Option Setting...
Page 17 TH-103PF10WK/TK/RK Option Menu for GPF10D series GPH10D chassis series have special function and operation setting facility called Option Menu. This Option Menu is use- ful for special function required customers. This should be set at the installation stage. Option menus...
Page 18: Troubleshooting Guide
TH-103PF10WK/TK/RK 6 Troubleshooting Guide 6.1. Self Check 6.1.1. Display Indication 1. Self-check is used to automatically check the bus line controlled circuit of the Plasma display. 2. To get into the Self-check mode, press the volume down button on the customer controls at the side of the set, at the same time pressing the OFF-TIMER button on the remote control, and the screen will show.
Page 19: Power Led Blinking Timing Chart
TH-103PF10WK/TK/RK 6.1.2. Power LED Blinking timing chart 1. Subject Information of LED Blinking timing chart. 2. Contents When an abnormality has occurred to the unit, the protection circuit operates and resets to the stand by mode. At this time, the defective block can be identified by the number of blinks of the Power LED on the front panel of the unit.
Page 20: No Power
TH-103PF10WK/TK/RK 6.2. No Power First check point There are following 3 states of No Power indication by power LED. 1. No lit. 2. Green is lit then turns red blinking a few seconds later. 3. Only red is lit. 6.3.
Page 21: Local Screen Failure
TH-103PF10WK/TK/RK 6.4. Local screen failure Plasma display may have local area failure on the screen. Fig - 1 is the possible defect P.C.B. for each local area. Fig - 1...
Page 22: Disassembly And Assembly Instructions
TH-103PF10WK/TK/RK 7 Disassembly and Assembly Instructions • To disassemble P.C.B., wait for 1 minute after power was off for discharge from electrolysis capacitors. • marks indicate screw positions. 7.1. Rear Cover and Board Rear Cover required to remove for each board exchange.
Page 23: Location Of Rear Cover Screws
TH-103PF10WK/TK/RK Board Name Rear Cover PB-Board P-Board (MULTI_1) P-Board (SUS_1) P-Board (MULTI_2) P-Board (SUS_2) F-Board PC-Board HX-Board HA-Board DN-Board HDMI-Board CD-Board (A) CD-Board (B) CD-Board (C) CD-Board (D) CD-Board (E) CD-Board (F) DR1-Board (A) DR1-Board (B) DR2-Board (A) DR2-Board (B) 7.2.
Page 24 TH-103PF10WK/TK/RK 7.2.1. Removal of Rear Cover ( A ) , ×2 2. Remove screws (×21 ) and then remove the Rear Cover ( A ). 1. Remove Eye Bolt Covers. 7.2.2. Removal of Rear Cover ( B ) , ×7 1.
Page 25 TH-103PF10WK/TK/RK 7.2.3. Removal of Rear Cover ( C ) 7.2.5. Removal of Rear Cover ( E ) 1. Remove screws (×19 ) and then remove the Rear 1. Remove screws (×25 ) and then remove the Rear Cover ( C ).
Page 26: Removal Of Side Angle (L
TH-103PF10WK/TK/RK 7.3.1. Removal of Side Angle (L) 1. Remove 4 screws (A) of the Plate. 2. Remove screws (×21 ) and then remove the Rear Cover ( F ). 2. Remove 19 screws and then remove the Side Angle (L).
Page 27: Removal Of Ha-Board
TH-103PF10WK/TK/RK 7.3.2. Removal of Side Angle (R) 5. Remove 19 screws and then remove the Side Angle (R). 1. Disconnect the connectors (DS15, SC34). 2. Remove 4 screws, and then side the Side Power Unit upward. 3. Remode the side Power Unit.
Page 28: Removal Of Hdmi-Board
TH-103PF10WK/TK/RK 7.5. Removal of HDMI-Board 3. Remove 11 screws and then remove DS-Board. 1. Remove 4 screws (E) and then remove the HDMI Termi- nal Block. 2. Remove 4 screws (F) and remove Shield Plate. 3. Remove 2 Hexagonal-Head screws (G) and then remove HDMI-Board.
Page 29: Removal Of Dn-Board
TH-103PF10WK/TK/RK 7.9. Removal of PB-Board HX-Board, and then remove HX-Board. 1. Disconnect the connectors (PB30, PB31, PB51, PB53, PB54, PB56, PB59, PB61, PB62, PB64, PB66, PB69, PB71). 2. Remove 4 screws and then remove PB-Board. 7.8. Removal of DN-Board 7.10. Removal of H5-Board 1.
Page 30: Removal Of D-Board
TH-103PF10WK/TK/RK 7.12. Removal of P-Board (MULTI_1), 3. Remove 3 screws (J) and then remove H5-Board. (MULTI_2) The fuses are not included in P-Board for the repair. 7.11. Removal of D-Board 7.12.1. Removal of P-Board (MULTI_1) 1. Disconnect the connectors (P5, P12, P25, P51, P53, P55).
Page 31: Removal Of P-Board (Sus_1), (Sus_2)
TH-103PF10WK/TK/RK 7.13. Removal of P-Board (SUS_1), 7.14. Removal of F-Board (SUS_2) The fuses (F900, F901, F903, F904) are not included in F- Board for the repair. The fuses are not included in P-Board for the repair. 1. Disconnect the connectors (F1, F8, F9).
Page 32: Removal Of Su-Board
TH-103PF10WK/TK/RK 7.16. Removal of SU-Board 6. Disconnect the connector (SU45). 1. Remove the Side Angle (R). (Refer to Removal of the Side Angle (L), (R) ) 7. Remove 9 screws. 2. Remove 6 screws and then remove the Reinforcement 8. Slide the SU-Board to the upper direction to remove the Angle (A).
Page 33: Removal Of Sm-Board
TH-103PF10WK/TK/RK 7.17. Removal of SM-Board from the connectors (SC43, SC46). 1. Remove the Side Angle (R). (Refer to Removal of the Side Angle (L), (R) ) 7.18. Removal of SD-Board 2. Disconnect the Fan relay connectors. 3. Remove 2 screws and then remove the Fan Block (A).
Page 34: Removal Of Sc-Board
TH-103PF10WK/TK/RK 7.19. Removal of SC-Board 4. Disconnect the connectors (SD52). 1. Remove SU-Board. (Refer to Removal of SU-Board) 5. Remove 9 screws. 2. Remove SM-Board. 6. Slide SD-Board to the bottom direction to remove SD- (Refer to Removal of SM-Board) Board from the connectors (SC47, SC48).
Page 35: Removal Of Sc2-Board
TH-103PF10WK/TK/RK 7.21. Removal of S1-Board and V2- 7. Remove 16 screws and then remove SC-Board. Board 7.21.1. Removal of S1-Board 1. Remove the Side Power Unit. (Reference to Removal of the Side Angle (L), (R)) 2. Remove 2 screws (K).
Page 36: Removal Of Ss2-Board
TH-103PF10WK/TK/RK 7.21.2. Removal of V2-Board 1. Removal the S1-Board (Refer to Removal of the S1-Board and V2-Board) 2. Remove 4 screws (M). 3. Disconnect the connector (V15) and then remove V2- Board. 5. Remove the flexible cables from the connectors (SS29, SS30,SS51, SS52, SS53, SS54).
Page 37: Removal Of Ss-Board
TH-103PF10WK/TK/RK 9. Remove 6 screws and then remove SS3-Board. 7.24. Removal of SS-Board 4. Remove 2 screws ( ) and then remove the Rear Cover Angle (H). 5. Remove 2 Eye Bolt Covers. 6. Remove 5 screws ( ) and then remove the Rear Cover Angle (F).
Page 38: Removal Of Fan
TH-103PF10WK/TK/RK 7.25. Removal of Fan 1. Disconnect the Fan relay connectors. 2. Remove each 4 screws of Fan Block (A), (B), (E), (H), (J) and then remove the Fan Blocks. 3. Remove each 4 screws of Fan (C), (F), (G) and then remove the Fans.
Page 39: Removal Of C1-Board
TH-103PF10WK/TK/RK 3. Remove 4 screws of the flexible cable. 4. Disconnect the connector (C14). 5. Remove the flexible cables from the connectors (CA1, CA2, C11). Note: • The Sponge (of Fans) is not re-useable. Please use a new one when Fan exchange.
Page 40: Removal Of C3-Board
TH-103PF10WK/TK/RK 1. Remove the Eye Bolt. 2. Remove 5 screws and then remove the Rear Cover Angle (C). 4. Remove the Reinforcement Angle (A). (Refer to Removal of C1-Board) 5. Remove 6 screws of the flexible cable. 3. Remove 6 screws and then remove the Reinforcement 6.
Page 41: Removal Of C4-Board
TH-103PF10WK/TK/RK 7.29. Removal of C4-Board 3. Remove 5 screws ( ) and then remove the Rear Cover Angle (E). 1. Remove the Rear Cover Angle (C). (Refer to Removal of C3-Board) 2. Remove the Reinforcement Angle (C). (Refer to Removal of C3-Board) 3.
Page 42: Removal Of C6-Board
TH-103PF10WK/TK/RK 7.32. Removal of C7-Board 7.31. Removal of C6-Board 1. Remove 7 screws and then remove the Fan Block (G) and Fan (K). 1. Remove the Fan (D). (Refer to Removal of C5-Board) 2. Remove the Reinforcement Angle (E). (Refer to Removal of C5-Board) 3.
Page 43: Removal Of C8-Board
TH-103PF10WK/TK/RK 6. Disconnect the connectors (C82, C84, C88). 7. Remove 6 screws and then remove C8-Board. 7. Remove 4 screws of the flexible cable. 8. Remove the flexible cables from the connectors (CB15, CB16, C71). 9. Disconnect the connector (C74).
Page 44: Removal Of Cx-Board
TH-103PF10WK/TK/RK 5. Disconnect the connector (CX4). 4. Remove 6 screws of the flexible cable. 5. Remove the flexible cables from the connectors ( C90, C91, C93,CB9, CB10, CB11). 6. Remove 5 screws and then remove CX-Board. 6. Disconnect the connectors (C92, C94).
Page 45: Removal Of Cz-Board
TH-103PF10WK/TK/RK 4. Remove the flexible cables from the connectors (CB1, 5. Remove 6 screws ( ) and then remove the Reinforce- CB2, CZ1). ment Angle (B). 5. Remove 4 screws and then remove CZ-Board. 6. Remove 6 screws of the flexible cable.
Page 46: Removal Of Dr1-Board (B)
TH-103PF10WK/TK/RK 7.39. Removal of DR1-Board (B) 7.41. Removal of DR2-Board (B) Attaching short jumper to connector (DR6). Attaching short jumper to connector (DR16). Attach Short Jumper to the connector (DR6) when replacing Attach Short Jumper to the connector (DR16) when replacing DR1-Board.
Page 47: Removal Of Cd-Board
TH-103PF10WK/TK/RK 7.42. Removal of CD-Board 7.42.3. Removal of CD-Board (C) 1. Remove the flexible cables from the connectors (CD1, CD2). 2. Remove 2 screws and then remove CD-Board (C). 7.42.1. Removal of CD-Board (A) 1. Remove the flexible cables from the connectors (CD1, 7.42.4.
Page 48: Removal Of Ac Inlet
TH-103PF10WK/TK/RK 2. Remove the flexible cables from the connectors (CD1, 2. Disconnect a connector (F1). CD2). 3. Remove 3 screws and then remove the AC-Inlet. 3. Remove 2 screws and then remove CD-Board (E). 7.44. Removal of Cabinet and Front Glass 7.42.6.
Page 49 TH-103PF10WK/TK/RK • Be sure to lift the instruction six positions of the figure, when remove the Front Glass. (Note) • When removing the Cabinet with Front Glass, take Note: When replacing the Front Glass care not to damage the flexible cable of the Plasma •...
Page 50 TH-103PF10WK/TK/RK Removal of Cabinet 7.44.2.2. Removeval of Cabinet Bottom 7.44.2. 1. Remove the Front Glass. 1. Remove each 5 screws ( ) (Refer to Removal of Front Glass.) 2. Remove each 2 screws ( ) and then remove the Con- nection Angles (A), (AS), (B), (BS).
Page 51: Removal Of V1-Board And V3-Board
TH-103PF10WK/TK/RK 7.44.2.4. Removeval of Cabinet Left 1. Remove each 5 screws ( ). 2. Remove each 2 screws ( ) and then remove the Con- nection Angles (A), (AS), (B), (BS). 7.46. Removal of Plasma Panel 1. Remove the Rear Covers.
Page 52 TH-103PF10WK/TK/RK 5. Remove 4 screws (Q) of the Plate. 10. Disconnect the each Fan relay connectors. • Remove each 4 screws and then remove the Fan Blocks (A), (B), (E), (F), (G), (H), (J). • Remove each 4 screws and then remove the Fan (C).
Page 53 TH-103PF10WK/TK/RK 15. Remove the flexible cables from the connectors (DN1, 22. Disconnect the connector (H51). DN6). 16. Disconnect the connectors (DN2, DN3, DN5). 17. Remove 6 screws and then remove DN-Board Block. 23. Disconnect the connectors (P2, P5, P9, P12, P25, P51, P53, P55).
Page 54 TH-103PF10WK/TK/RK 27. Disconnect the connectors ( SC13, SC14, SC34, SC83, 35. Remove 6 screws and then remove the Fixed Angle. SC84). 28. Remove 4 screws and then remove SC2-Board. 36. Disconnect a connector (CY0) connected with CY-Board. 37. Remove 2 screws and then remove CD-Board (F).
Page 55 TH-103PF10WK/TK/RK 40. Remove 4 screws and then remove CD-Board (B), (C). 44. Remove 4 screws and then remove CD-Board (D), (E). 41. Remove each 1 screw ( ) and then remove the Flexible Holders (6 places). 42. Remove each 6 screws ( ) and then remove the Fixed Angles (2 places).
Page 56 TH-103PF10WK/TK/RK 49. Remove the PB-Board. 50. Remove 2 screws and then remove AC Inlet Cover. 51. Remove 3 screws and then remove the AC-Inlet. 52. Remove the Plasma Panel. (Note) • When replacing the Plasma Panel, use a hanging device (machine) such as cranes, because the Plasma Panel is too heavy.
Page 57 TH-103PF10WK/TK/RK Structure of replacement Plasma Panel (Spare Parts)
Page 58: Measurements And Adjustments
TH-103PF10WK/TK/RK 8 Measurements and Adjustments 8.1. Adjustment Procedure 8.1.1. Driver Set-up 8.1.1.1. Item / Preparation 1. Set Aging pattern 1 (White pattern) by IIC mode. 2. Set the picture adjustment items as follows. • Picture menu : Standard • Color temperature : Normal •...
Page 59: Initialization Pulse Adjust
TH-103PF10WK/TK/RK 8.1.2. Initialization Pulse Adjust 1. Set Aging pattern 1 (White pattern) by IIC mode. 2. Set the picture adjustment items as follows. • Picture menu : Standard • Color temperature : Normal • Picture : 25 • Aspect : Full 3.
Page 60 TH-103PF10WK/TK/RK 8.1.3. P.C.B. (Print Circuit Board) Replacement 8.1.3.1. Caution 1. To remove P.C.B., wait 1 minute after power was off for discharge from electrolysis capacitors. 8.1.3.2. Quick adjustment after P.C.B. Replacement Adjust the following voltages with the multimeter. P.C.B. Name...
Page 61 TH-103PF10WK/TK/RK 8.1.4. Adjustment Volume Location 8.1.5. Test Point Location...
Page 62: Adjustment
TH-103PF10WK/TK/RK 8.2. Adjustment 8.2.1. RGB white balance adjustment Instrument Name Connection Remarks • RGB VGA W / B pattern PC input User setting: Normal • Color analyzer (Minolta CA-100 or equivalent) Panel surface (Picture menu: Standard) Procedure Remarks • Ensure aging is adequate.
Page 63 TH-103PF10WK/TK/RK...
Page 64: Hd White Balance Adjustment
TH-103PF10WK/TK/RK 8.2.2. HD white balance adjustment Instrument Name Connection Remarks • HD W / B pattern (COMPONENT Output) PC input User setting: Normal • Color analyzer (Minolta CA-100 or equivalent) Panel surface (Picture menu: Standard) Procedure Remarks • Ensure aging is adequate.
Page 65 TH-103PF10WK/TK/RK...
Page 66: Power Control Adjustment
TH-103PF10WK/TK/RK 8.2.3. Power control adjustment Instrument Name Connection Remarks • PC (RGB) signal generator • PC input Set “RGB” at ‘COMPONENT / RGB-IN (Leader: VGA / No.9 signal) SELECT’ in Setup Menu. • Connect the AC power of the adjust- •...
Page 98: Lead Wiring (1)
TH-103PF10WK/TK/RK 10.8. Lead Wiring (1)
Page 99: Lead Wiring (2)
TH-103PF10WK/TK/RK 10.9. Lead Wiring (2)
Page 100: Lead Wiring (3)
TH-103PF10WK/TK/RK 10.10. Lead Wiring (3)
Page 101: Lead Wiring (4)
TH-103PF10WK/TK/RK 10.11. Lead Wiring (4)
Page 102: Lead Wiring (5)
TH-103PF10WK/TK/RK 10.12. Lead Wiring (5)
Page 103: Lead Wiring (6)
TH-103PF10WK/TK/RK 10.13. Lead Wiring (6)
Page 104 TH-103PF10WK/TK/RK 10.14. Lead Wiring (7)
Page 105 TH-103PF10WK/TK/RK 10.15. Lead Wiring (8)
Page 106 TH-103PF10WK/TK/RK 10.16. Lead Wiring (9)
Page 107 Model No. : TH-103PF10WK/TK/RK Caution...
Page 108 Model No. : TH-103PF10WK/TK/RK Exploded View...
Page 109 Model No. : TH-103PF10WK/TK/RK Side Power part location...
Page 110 Model No. : TH-103PF10WK/TK/RK Cabinet part location...
Page 111 Model No. : TH-103PF10WK/TK/RK Fan part location...
Page 112 Model No. : TH-103PF10WK/TK/RK Rear cover location...
Page 113 Model No. : TH-103PF10WK/TK/RK Cable relation...
Page 114 Model No. : TH-103PF10WK/TK/RK Board and Fuse...
Page 115 Model No. : TH-103PF10WK/TK/RK Packing summary (1)
Page 116 Model No. : TH-103PF10WK/TK/RK Packing summary (2)
Page 117 Model No. : TH-103PF10WK/TK/RK Packing summary (3)
Page 118 Model No. : TH-103PF10WK/TK/RK Packing summary (4)
Page 119 Model No. : TH-103PF10WK/TK/RK Packing summary (5)
Page 120 Model No. : TH-103PF10WK/TK/RK Packing summary (6)
Page 121 Model No. : TH-103PF10WK/TK/RK Packing summary (7)
Page 122 Model No. : TH-103PF10WK/TK/RK Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks EUR7636070R REMOTE CONTROLLER K2CK3YY00003 AC CORD 1 WK K2CN3YY00003 AC CORD 1 WK/RK K2CT3YY00002 AC CORD 1 WK K2CG3YY00024 AC CORD 1 TK L6FAYYYH0030...
Page 123 Model No. : TH-103PF10WK/TK/RK Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks TMME287 CLAMPER TMME292 CLAMPER TMMX158 COVER (EDGE GAURD) TMMJ068 RUBBER(FAN) TMWC016 POWER BUTTON BRACKET TMXX033 CORE HOLDER TMXX035 AC CORD CLAMPER A TMMX169 AC CORD CLAMPER B...
Page 124 Model No. : TH-103PF10WK/TK/RK Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks TSXL576 CABLE(D35-CD1) TSXL577 CABLE(C90-CD2) TSXL578 CABLE(D36-CD1) TSXL579 CABLE(CY0-CD2) TSXL584 CABLE(DN6-DS6) TSXL585 CABLE(DN1-DS1) TTUA1515-1 REAR COVER(SIDE/LEFT) TTUA1518 REAR COVER(CENTER/LEFT/BOTTOM) TTUA1520 REAR COVER(CENTER/RIGHT/BOTTOM) TTUA1747-1 REAR COVER(SIDE/RIGHT)
Page 125 Model No. : TH-103PF10WK/TK/RK Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks XYN4+F10FJ SCREW XYN4+F10FJK SCREW XYN4+F32FJ SCREW XYN4+J10FJ SCREW XYN5+F15FJ SCREW XYN5+F30FJK SCREW XYN8+F20FJK SCREW XZBT6506 POLY BAG FOR INST.BOOK F900 K5D103BMA001 TIME LAG FUSE HIGH...
Page 126 Model No. : TH-103PF10WK/TK/RK Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks TNPA4086 CIRCUIT BOARD V2 TNPA4087 CIRCUIT BOARD V3 TNPA4100 CIRCUIT BOARD DR2 TNPA4103 CIRCUIT BOARD PB TNPA4386 CIRCUIT BOARD DS TXNHA10RBS CIRCUIT BOARD HA...

This manual is also suitable for:

Th-103pf10tk Th-103pf10rk

Panasonic TH-103PF10WK Service Manual

1 Safety Precautions

2 Warning

3 Service Navigation

4 Specifications

5 Service Mode

6 Troubleshooting Guide

7 Disassembly and Assembly Instructions

8 Measurements and Adjustments

9 Block Diagram

10 Wiring Connection Diagram

Quick Links

TABLE OF CONTENTS

Related Manuals for Panasonic TH-103PF10WK

Summary of Contents for Panasonic TH-103PF10WK

This manual is also suitable for:

Table of Contents