Brother DCP-8110DN Service Manual page 64

Error
Problem
codes
4500 An unidentified error occurred.
4600 An unidentified error occurred.
4700 An unidentified error occurred.
4800 An unidentified error occurred.
4900 An unidentified error occurred.
4A00 An unidentified error occurred.
4B00 An unidentified error occurred.
4C00 An unidentified error occurred.
4D00 An unidentified error occurred.
4E00 An unidentified error occurred.
4F00 An unidentified error occurred.
The number of rotations of the
5000 drum unit has reached the life
limit. (Printing does not stop.)
Printable pages set for the MP
5100 paper feeding kit have reached
the limit. (Printing does not stop.)
Printable pages set for paper
5200 feeding kit 1 have reached the
limit. (Printing does not stop.)
Printable pages set for paper
5300 feeding kit 2 have reached the
limit. (Printing does not stop.)
Printable pages set for the fuser
5400 unit have reached the limit.
(Printing does not stop.)
Printable pages set for the laser
5500 unit have reached the limit.
(Printing does not stop.)
The eject sensor detected that
5600
the fuser cover was open.
The registration front sensor
does not detect paper pass
5700 within the specified time after the
first side was printed in duplex
printing mode.
Any of error codes 6A00 to 6F00,
7600, 7800, DD00,DE00, or E200
5800 (fuser unit error) occurred when
the power switch was turned ON
or sleep mode was released.
Rechecking the error after the power
switch was turned OFF and then ON
again because an error was detected
by the center thermistor of the fuser
5900
unit. (This message is displayed for
approximately 15 minutes when the
machine is restarted after error code
5800 has occurred.)
5A00 An unidentified error occurred.
Refer Error
to: codes
2-35 5B00 An unidentified error occurred.
2-35 5C00 An unidentified error occurred.
2-35 5D00 An unidentified error occurred.
2-35 5E00 An unidentified error occurred.
2-35 5F00 An unidentified error occurred.
2-35 6000 An unidentified error occurred.
2-35 6100 An unidentified error occurred.
2-35 6200 An unidentified error occurred.
The toner sensor detected no toner
2-35 6300 remaining or the number of rotations of the
developer roller has reached the upper limit.
2-35 6400 An unidentified error occurred.
2-35 6500 An unidentified error occurred.
2-35 6600 An unidentified error occurred.
The toner sensor detected that the toner
remaining has fallen below the specified
2-36 6700
level or the developer roller counter has
exceeded the specified value.
2-36 6800 An unidentified error occurred.
2-36 6900 An unidentified error occurred.
The center thermistor of the fuser unit
2-36 6A00 has not reached the specified
temperature within the specified time.
The center thermistor of the
fuser unit has not reached the
2-36 6B00
specified temperature within the
specified time.
The center thermistor of the
fuser unit detected a
2-37 6C00
temperature higher than the
specified value.
After the heat unit was heated
normally, the center thermistor of
2-37 6D00 the fuser unit detected a
temperature lower than the
specified value.
The center thermistor of the
2-38 6E00 fuser unit detected that the heat
unit was not heated.
The center thermistor or the side
2-38 6F00 thermistor of the fuser unit
detected a temperature error.
2-38 7000 An unidentified error occurred.
2-19
Refer
Problem
2-38
2-38
2-38
2-38
2-38
2-38
2-38
2-38
2-39
2-39
2-39
2-39
2-39
2-39
2-39
2-40
2-40
2-40
2-40
2-40
2-40
2-41
Confidential
to: