World Time - Casio 3034 Operation Manual

Operation Guide 3034
• This watch is designed to receive the time calibration signal transmitted from Rugby,
England and the signal from Mainflingen, Germany.
Reception Ranges
1,500 kilometers
Rugby
500 kilometers
• At distances further than about 500 kilometers from a transmitter, signal reception
may not be possible during certain times of year or times of day. Radio interference
may also cause problems with reception.
• Even when the watch is within the reception range of the transmitter, signal
reception is impossible if the signal is blocked by mountains or other geological
formations between the watch and signal source.
• Signal reception is affected by weather, atmospheric conditions, and seasonal
changes.
• See the information under "Signal Receive Troubleshooting" if you experience
problems with time calibration signal reception.
About Auto Receive
With auto receive, the watch receives the time calibration signal automatically up to six
times a day. When any auto receive is successful, the remaining auto receive
operations are not performed. The start times of the auto receive operations depend
on the current Home City and DST settings.
Home City Auto Receive Start Times
1 2
LIS Standard Time 1:00 am 2:00 am
LON Daylight Saving 2:00 am 3:00 am
Time
BCN Standard Time 2:00 am 3:00 am
MAD
PAR Daylight Saving 3:00 am 4:00 am
MIL Time
ROM
BER
STO
ATH Standard Time 3:00 am 4:00 am
Daylight Saving 4:00 am 5:00 am
Time
Note
• Auto receive works only while the watch is in the Timekeeping Mode or World Time
Mode. Auto receive is not performed if an auto receive time is reached while an
alarm is sounding, while a countdown timer operation is in progress, or while a
setting screen (a screen with a flashing setting) is on the display.
• Auto receive of the calibration signal is designed to be performed early in the
morning, while you sleep (provided that the Timekeeping Mode time is set correctly).
Before going to bed for the night, remove the watch from your wrist, and put it in a
location where it can receive the signal easily.
• When auto receive is turned on, the watch receives the calibration signal for two to
five minutes everyday when the Timekeeping Mode time reaches each of the
calibration times. Do not perform any button operation within five minutes before or
after any one of the calibration times. Doing so can interfere with correct calibration.
• Remember that reception of the calibration signal depends on the time kept in the
Timekeeping Mode. The receive operation will be performed whenever the display
shows any one of the calibration times, regardless of whether or not the
Timekeeping Mode time actually is the correct time.
About the Receiving Indicator
The receiving indicator shows the strength of the calibration signal being received. For
best reception, be sure to keep the watch in a location where signal strength is
strongest.
Weak
(Level 0)
Receiving indicator
• Even in an area where signal strength is strong, it takes about 10 seconds for signal
reception to stabilize enough for the receiving indicator to indicate signal strength.
• Use the receiving indicator as a guide for checking signal strength and for finding the
best location for the watch during signal receive operations.
• Following reception of the time calibration signal and calibration of the watch's time
setting, the Level 3 receiving indicator will remain on the display in all modes. The
Level 3 receiving indicator will not be displayed if signal reception was unsuccessful
or after you adjust the current time setting manually.
• The Level 3 receiving indicator is displayed only when the watch is able to receive
both time and date data successfully. It does not appear when only time data is
received.
• The Level 3 receiving indicator indicates that at least one of the auto calibration
signal receive operations was successful. Note, however, that the Level 3 receiving
indicator is cleared from the display when the first auto receive operation of the day
is performed.
To perform manual receive
1. Place the watch on a stable surface so its top (12
o'clock side) is facing towards a window.
2. In the Timekeeping Mode, hold down C for about two
seconds until RC! appears on the display.
• Time calibration signal reception takes from two to five
minutes, but in some cases it can take as long as 12
minutes. Take care that you do not perform any button
operations or move the watch during this time.
• After signal reception is complete, the display of the
Receiving indicator
watch changes to the Last Signal screen.
Mainflingen
3 4 5 6
3:00 am 4:00 am 5:00 am Midnight
4:00 am 5:00 am Midnight 1:00 am
next day
4:00 am 5:00 am Midnight 1:00 am
next day
5:00 am Midnight 1:00 am 2:00 am
next day next day
5:00 am Midnight 1:00 am 2:00 am
next day next day
Midnight 1:00 am 2:00 am 3:00 am
next day next day next day
Strong
(Level 3)
Note
• To interrupt a receive operation and return to the Timekeeping Mode, press C.
• If the receive operation is unsuccessful, the message
for about one or two minutes. After that, the watch returns to the Timekeeping Mode.
• You can also change from the Last Signal or
timekeeping screen by pressing C.
To turn auto receive on and off
1. In the Timekeeping Mode, press C to display the Last
Signal screen.
2. Hold down A until the current auto receive setting (
or ) starts to flash. This is the setting screen.
OFF
• Note that the setting screen will not appear if the
currently selected Home City is one that does not
support time calibration reception.
3. Press C to toggle auto receive on (
4. Press A to exit the setting screen.
On/Off status
• For information about city codes that support signal
receive, see "To set your Home City".
To display the Last Signal screen
In the Timekeeping Mode, press C to display the Last Signal screen (indicated by
GET ). The Last Signal screen shows the date and time of the last successful time
calibration signal reception.
DST indicator
Month – Day
Press C.
Hour : Minutes
PM indicator Seconds
Signal Receive Troubleshooting
Check the following points whenever you experience problems with calibration signal
reception.
Problem Probable Cause
• The watch is not in the Timekeeping
Cannot perform
manual receive. Mode.
• Your current Home City is not one of the
following city codes:
LIS, LON, BCN, MAD, PAR, MIL, ROM,
BER, STO, or ATH.
• You changed the time setting manually.
Auto receive is
• The watch was not in the Timekeeping
turned on, but
the Level 3 or World Time Mode, or you performed
receiving some button operation during the auto
indicator does receive operation.
• Even if receive is successful, the Level 3
not appear on
the display. receiving indicator disappears from the
display each day when the first auto
receive operation of the day is
performed.
• Time data (hour, minutes, seconds) only
was received during the last receive
operation. The Level 3 receiving
indicator appears only when time data
and date data (year, month, day) are
both received.
• If the time is one hour off, the DST
Time setting is
incorrect setting may be incorrect.
• The Home City code setting is not
following signal
reception. correct for the area where you are using
the watch.
• For further information, see "Important!" under "Time Calibration Signal Reception"
and "Radio-controlled Timekeeping Precautions".

World Time

The World Time Mode shows you the current time in 48
City code
cities (29 time zones) around the world.
• If the current time shown for a city is wrong, check your
Home City time settings and make the necessary
changes.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing B.
Current time in
selected city
To view the time in another city
While in the World Time Mode, press C to scroll eastward through the city codes
(time zones).
• For full information on city codes, see "City Code Table".
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use C to display the city code
(time zone) whose Standard Time/Daylight Saving Time
DST indicator
setting you want to change.
2. Hold down A to toggle Daylight Saving Time (DST
indicator displayed) and Standard Time (DST indicator
not displayed).
• The DST indicator will appear whenever you display a
city code for which Daylight Saving Time is turned on.
• Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
affected.
ERR appears on the display
ERR screen to the normal
ON
) and off ( ).
ON OFF
Receive date
Receive time
Last Signal Screen
What you should do
• Enter the Timekeeping Mode
and try again.
• Select LIS, LON, BCN, MAD,
PAR, MIL, ROM, BER, STO,
or ATH as your Home City.
• Perform manual signal receive
or wait until the next auto
signal receive operation is
performed.
• Check to make sure the
watch is in a location where it
can receive the signal.
• Change the DST setting to
Auto DST.
• Select the correct Home City
code.
2