Download Print this page

World Time - Casio 3017 Operation Manual

Advertisement

Operation Guide 3017
• Signal reception is normally better at night than during the day.
• Time calibration signal reception takes from two to six minutes, but some cases it
can take as long as 12 minutes. Take care that you do not perform any button
operations or move the watch during this time.
• When within range of the applicable transmitter, this watch can receive either the
Germany (Mainflingen) or England (Rugby) time calibration signals.
See "Transmitters" for more information.
Reception Ranges
1,500 kilometers
Rugby
500 kilometers
• This watch is designed to receive the time calibration signal transmitted from
Mainflingen, Germany and the signal from Rugby, England. Signal reception is
possible within the area represented by a circle with a radius of about 1,500
kilometers.
• At distances further than about 500 kilometers from a transmitter, signal reception
may not be possible during certain times of year or times of day. Radio interference
may also cause problems with reception.
• Even when the watch is within the reception range of the transmitter, signal
reception will be impossible if the signal is blocked by mountains or other geological
formations between the watch and signal source.
• Signal reception is affected by weather, atmospheric conditions, and seasonal
changes.
• See the information under "Signal Reception Troubleshooting" if you experience
problems with time calibration signal reception.
About Auto Receive
The watch receives the time calibration signal automatically up to six times a day.
When any auto receive is successful, the remaining auto receive operations are not
performed. The reception schedule (calibration times) depends on your currently
selected Home City, and whether standard time or Daylight Saving Time is selected
for your Home City.
Note
• Auto receive is turned on whenever LIS, LON, BCN, MAD, PAR, MIL, ROM, BER,
STO, or ATH is selected as the Home City code.
Your City Code
1
LIS, LON Standard Time
1:00 am 2:00 am 3:00 am 4:00 am 5:00 am Midnight
(GMT +0)
Daylight Saving
2:00 am 3:00 am 4:00 am 5:00 am Midnight 1:00 am
Time
BCN, MAD
Standard Time
2:00 am 3:00 am 4:00 am 5:00 am Midnight 1:00 am
PAR, MIL
ROM, BER
Daylight Saving
3:00 am 4:00 am 5:00 am Midnight 1:00 am 2:00 am
STO
Time
(GMT +1)
ATH
Standard Time
3:00 am 4:00 am 5:00 am Midnight 1:00 am 2:00 am
(GMT +2)
Daylight Saving
4:00 am 5:00 am Midnight 1:00 am 2:00 am 3:00 am
Time
Note
• Auto receive works only while the watch is in the Timekeeping Mode or World Time
Mode. Auto receive is not performed if an auto receive time is reached while an
alarm is sounding, while a countdown timer operation is in progress, or while a
setting screen (a screen with a flashing setting) is on the display.
• Auto receive of the calibration signal is designed to be performed early in the
morning, while you sleep (provided that the Timekeeping Mode time is set correctly).
Before going to bed for the night, remove the watch from your wrist, and put it in a
location where it can receive the signal easily.
• When auto receive is turned on, the watch receives the calibration signal for two to
five minutes everyday when the Timekeeping Mode time reaches each of the
calibration times. Do not perform any button operation within five minutes before or
after any one of the calibration times. Doing so can interfere with correct calibration.
• Remember that reception of the calibration signal depends on the time kept in the
Timekeeping Mode. The receive operation will be performed whenever the display
shows any one of the calibration times, regardless of whether or not the
Timekeeping Mode time actually is the correct time.
• Calibration signal reception is disabled while a countdown timer operation is in
progress.
About the Receiving Indicator
The receiving indicator shows the strength of the calibration signal being received. For
best reception, be sure to keep the watch in a location where signal strength is
strongest.
Receiving indicator
Weak
(Level 0)
• Even in an area where signal strength is strong, it takes about 10 seconds for signal
reception to stabilize enough for the receiving indicator to indicate signal strength.
• Use the receiving indicator as a guide for checking signal strength and for finding the
best location for the watch during signal receive operations.
• Following reception of the time calibration signal and calibration of the watch's time
setting, the Level 3 receiving indicator will remain on the display in all modes. The
Level 3 receiving indicator will not be displayed if signal reception was unsuccessful
or after you adjust the current time setting manually.
• The Level 3 receiving indicator is displayed only when the watch is able to receive
both time and date data successfully. It does not appear when only time data is
received.
• The Level 3 receiving indicator indicates that at least one of the auto calibration
signal receive operations was successful. Note, however, that the Level 3 receiving
indicator is cleared from the display when the first auto receive operation of the day
is performed.
Mainflingen
Auto Receive Start Times
2
3
4
5
6
next day
next day
next day next day
next day next day
next day next day next day
Strong
(Level 3)
To perform manual receive
1. Place the watch on a stable surface so its top (12
o'clock side) is facing towards a window.
Receiving indicator
2. In the Timekeeping Mode, hold down D for about two
seconds until RC! appears on the display.
• Time calibration signal reception takes from two to six
minutes, but some cases it can take as long as 12
minutes. Take care that you do not perform any button
operations or move the watch during this time.
• After signal reception is complete, the display of the
watch changes to the Last Signal screen.
Note
• To interrupt a receive operation and return to the Timekeeping Mode, press D.
• If the receive operation is unsuccessful, the message
for about one or two minutes. After that, the watch returns to the Timekeeping Mode.
• You can also change from the Last Signal or
timekeeping screen by pressing D.
• Calibration signal reception is disabled while a countdown timer operation is in
progress.
To turn auto receive on and off
1. In the Timekeeping Mode, press D to display the Last
On/Off Status
Signal screen.
2. Hold down A until the receiving indicator and current
auto receive setting (
the setting screen.
• Note that the setting screen will not appear if the
currently selected Home City is one that does not
support time calibration reception.
3. Press D to toggle auto receive on (
4. Press A to exit the setting screen.
• For information about city codes that support signal receive, see "To set your Home
City".
To display the Last Signal screen
In the Timekeeping Mode, press D to display the Last Signal screen (indicated by
GET
). The Last Signal screen shows the date and time of the last successful time
calibration signal reception.
• In the Timekeeping Mode, you can press A to toggle the display contents.
Day of week
PM indicator
Press D.
Hour : Minutes
Seconds
Signal Receive Troubleshooting
Check the following points whenever you experience problems with calibration signal
reception.
Problem
Probable Cause
• The watch is not in the Timekeeping
Cannot perform
manual receive.
Mode.
• Your current Home City is not one of the
following city codes:
LIS, LON, BCN, MAD, PAR, MIL, ROM,
BER, STO, or ATH.
• You changed the time setting manually.
Auto receive is
• The watch was not in the Timekeeping
turned on, but
or World Time Mode, or you performed
the Level 3
some button operation during the auto
receiving
receive operation.
indicator does
• Even if receive is successful, the Level
not appear on
3 receiving indicator disappears from
the display.
the display each day when the first
auto receive operation of the day is
performed.
• Time data (hour, minutes, seconds) only
was received during the last receive
operation. The Level 3 receiving
indicator appears only when time data
and date data (year, month, day) are
both received.
• If the time is one hour off, the DST
Time setting is
incorrect
setting may be incorrect.
• The Home City code setting is not
following signal
reception.
correct for the area where you are using
the watch.
• For further information, see "Important!" under "Time Calibration Signal Reception"
and "Radio-controlled Timekeeping Precautions".

World Time

The World Time Mode shows you the current time in 48
City code
cities (29 time zones) around the world.
• If the current time shown for a city is wrong, check your
Home City time settings and make the necessary
changes.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
Current time in selected city
To view the time in another city
While in the World Time Mode, press D to scroll through the city codes (time zones)
to the east.
• For full information on city codes, see "City Code Table".
ERR
appears on the display
ERR
screen to the normal
or
) start to flash. This is
) and off (
).
Last Signal Screen
Receive time
Receive date
What you should do
• Enter the Timekeeping Mode
and try again.
• Select LIS, LON, BCN, MAD,
PAR, MIL, ROM, BER, STO,
or ATH as your Home City.
• Perform manual signal receive
or wait until the next auto
signal receive operation is
performed.
• Check to make sure the
watch is in a location where it
can receive the signal.
• Change the DST setting to
Auto DST.
• Select the correct Home City
code.
2

Hide quick links:

Advertisement

loading

This manual is also suitable for:

3016