Husqvarna 5524 STE Operator's Manual page 21

REPAIR PARTS
SNOW THROWER - MODEL NO. 5224STE
KEY PART
NO. NO. DESCRIPTION
4 532 19 10-79 Pulley, Impeller
5 532 18 89-09 Bearing Assembly, Flange
6 532 15 53-77 Nut, Hex Flange 5/16-18
7 532 18 03-55 Bolt, Flat Head, Carriage
5/16-18 x 5/8
8 872 27 05-05 Bolt, Carriage 5/16-1 8 x 5/8
9 532 16 31-83 Bolt
10 532 40 78-80 Housing, Auger
11 532 41 62-15 Bar, Scraper
12 532 18 40-95 Bracket, Corner Discharge
13 532 17 53-22 Base, Discharge Chute
14 810 04 05-00 Washer, Lock 5/16
15 819 11 15-07 Washer, Flat
16 874 94 05-16 Cap Screw HXHD 5/16-18 x 1
17 532 40 56-37 Grease Fitting
18 532 17 95-82 Screw, Hex Head 5/16 x 1
19 873 80 04-00 Nut, Hex Lock 1/4-20
20 532 15 53-77 Nut, Hex Lock 5/16-18
22 532 40 78-34 Skid Plate, Heavy Duty
25 872 27 05-06 Bolt, Shoulder 1/4-20
26 532 17 46-58 Bearing, Auger
27 532 17 46-97 Washer, Thrust, 1"
28 532 19 86-36 Bolt, Shear
30 532 40 78-50 Auger Assembly, RH
NOTE: All component dimensions given in U.S. inches.
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
AUGER HOUSING / IMPELLER ASSEMBLY
5224STE (96193001403), PRODUCT NO. 961 93 00-14
KEY PART
NO. NO.
31 532 40 78-66
32 532 40 77-68
33 532 40 77-69
34 532 17 46-81
35 532 17 46-84
36 532 40 77-57
37 532 17 46-83
38 532 40 77-58
39 532 40 77-67
40 532 40 77-60
41 532 40 77-61
42 532 40 77-70
43 532 40 77-62
44 532 18 92-82
45 532 40 77-63
46 532 40 77-64
47 532 40 77-65
48 532 18 41-05
49 874 78 04-26
50 532 40 77-66
51 532 18 42-05
55 532 19 86-38
56 532 18 06-84
57 532 19 67-10
58 532 41 19-39
21
DESCRIPTION
Auger Assembly, LH
O-Ring
Bushing, Flange 3/4
Washer, Thrust 3/4
Bearing, Thrust 3/4
Shaft, Impeller
Washer, Thrust 5/8
Bushing, Flange 5/8
Screw, Hex Head 5/16-18 x 3/4
Plug, Case
Housing, Gearbox, RH
Seal, Oil
Bushing, Flange, 1"
Key, Square 1/4 x 1/4 x 7/8
Gear, Worm
Shaft, Auger
Housing, Gearbox, LH
Impeller Assembly
Screw, Hex Head 1/4-20 x 1-5/8
Gasket, Gearbox
Pin, Roll 3/16 x 1-1/8
Spacer
Multi-Wrench
Gearbox Assembly
Plug Bearing Hole
1 inch = 25.4 mm