Page 1
M7350 LTE-Advanced Mobile WiFi REV 1.0.0 1910011149...
Page 2
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1)This device may not cause interference, and (2)This device must accept any interference, including interference that may cause undesired...
安全諮詢及注意事項 ● 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 ● 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。 ● 注意防潮,請勿將水或其他液體潑灑到本產品上。 ● 插槽與開口供通風使用,以確保本產品的操作可靠並防止過熱,請勿堵塞或覆蓋開口。 ● 請勿將本產品置放於靠近熱源的地方。除非有正常的通風,否則不可放在密閉位置中。 ● 請不要私自打開機殼,不要嘗試自行維修本產品,請由授權的專業人士進行此項工作。 Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України. Safety Information When product has power button, the power button is one of the way to shut off the product; ...
DECLARATION OF CONFORMITY For the following equipment: Product Description: LTE-Advanced Mobile WiFi Model No.: M7350 Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:...
Make sure that the package contains the above items. If any of the listed items is damaged or missing, please contact your distributor. Conventions The Device or M7350 mentioned in this guide stands for M7350 LTE-Advanced Mobile WiFi without any explanation.
Chapter 1. Introduction 1.1 Product Overview TP-LINK’s M7350 is at the forefront of wireless 4G sharing. Just insert a 4G SIM card into the device to instantly establish a selectable dual band Wi-Fi hotspot. With up to 150Mbps download and 50Mbps upload speeds, the M7350 is able to provide 4G wireless sharing to up to 15 users simultaneously.
M7350 LTE-Advanced Mobile WiFi User Guide 1.3 Physical Description Figure 1-1 the Exterior The details about the Exterior are explained as below. MENU button: Press this button to enter the menu screen or scroll down. You can also press this button until the screen appears to start WPS.
Page 12
M7350 LTE-Advanced Mobile WiFi User Guide The screen Indication: Item Description Indication Network type & Indicates the current network option: 2G /3G /4G, and Signal strength signal strength of current network. Internet connection Indicates the successful network connection. Indicates you are in roaming service.
M7350 LTE-Advanced Mobile WiFi User Guide Chapter 2. Hardware Installation 2.1 Environment Requirements Place the Device in a well-ventilated place far from any heater or heating vent Avoid direct irradiation of any strong light (such as sunlight) Keep at least 2 inches (5 cm) of clear space around the Device ...
Page 14
1) Touch the metal contacts of the battery to the metal points of the Device, and then press to fit the battery body into the slot. 2) Close the cover by pressing it. STEP 3: Turn on the M7350 Hold the button until the screen appears as shown below. (You can also hold the...
Page 15
If M7350 is connected to a computer with an USB cable, you can access its micro SD memory card just as access a hard disk. Connect one end of the USB cable to the micro USB port of M7350 and the other end to the USB port of your PC.
M7350 LTE-Advanced Mobile WiFi User Guide Chapter 3. Quick Installation Guide This chapter will guide you to quickly set up the basic functions for your M7350. 3.1 System Requirements SIM card with Internet access enabled. Computer supports the 2.4GHz/5GHz wireless band.
Page 17
M7350 LTE-Advanced Mobile WiFi User Guide Note: The default SSID (also called Wireless Network Name) of the device is TP-LINK_M7350_XXXXXX. (XXXXXX is the last 6 characters of the device’s MAC address.) You can check the SSID and Password on the screen or rear cover label.
When Connected appears behind the SSID of M7350, you’ve successfully connected to its wireless network. Note: After successful connection to M7350 (with a SIM card inserted), you can enjoy the 4G mobile connection instantaneously. If not, please refer to and retry. 3.4 Quick Setup 3.4.1 Quick Setup via your phone...
Page 19
M7350 LTE-Advanced Mobile WiFi User Guide After successful login, there will appear the following page. You can set up a new login username and password on this page, and click Done to continue. Click Dial-up to configure the basic network settings for accessing network. On the Dial-up page shows the ISP information of the SIM card inserted.
Page 20
Profile List. On the Wireless page, you can create a unique and easy-to-remember wireless network name (SSID) as well as Wireless Password, or you can keep it default. Then click Done to save your settings and reboot your M7350. -12-...
M7350 LTE-Advanced Mobile WiFi User Guide 3.4.2 Quick Setup via your PC Open a web-browser, enter the default address http://tplinkmifi.net or 192.168.0.1 in the Address field and then press Enter. When the login window appears, enter admin (in lower case letters) for both Username and Password, and then click the Login button or press the Enter.
Page 22
M7350 LTE-Advanced Mobile WiFi User Guide Note: If the above screen does not pop-up, it means that your Web-browser has been set to a proxy. Go to Tools menu > Internet Options > Connections > LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it.
Page 23
M7350 LTE-Advanced Mobile WiFi User Guide Wizard – Dial-up Settings Figure 3-3 On the Wireless Settings page, you can create a unique and easy-to-remember wireless network name (SSID) as well as Wireless Password, or you can keep it default. Then click Next to continue.
Page 24
M7350 LTE-Advanced Mobile WiFi User Guide Wizard – Finish Figure 3-5 -16-...
LTE-Advanced Mobile WiFi User Guide Chapter 4. Device Configuration After the successful login to the web-based management page of M7350, you will see the main menu listing Wizard, Status, SMS and Advanced on the top. In the following parts, these items will be explained in details, about their respective functions and configurations.
M7350 LTE-Advanced Mobile WiFi User Guide Statistics: Displays the device's data usage statistics, including the data monthly used/total used and the data daily used. The data usage accounting may differ from your carrier's, and it is subject to your carrier's statistics.
M7350 LTE-Advanced Mobile WiFi User Guide Click Refresh to refresh the inbox, and get any new message. Click Delete to delete the message(s) select. 4.3.2 New Message Figure 4-5 New Message Phone Number: Enter the receiver’s phone number. Content: Text your message in this box. The message you are texting is limited to 160 ...
M7350 LTE-Advanced Mobile WiFi User Guide Click Delete to delete the message(s) you select. 4.3.4 Draft Box You can review the unsent saved message(s) on this page. Figure 4-7 Drafts Box Phone Number: Shows the phone number that this message was planned to be sent to.
M7350 LTE-Advanced Mobile WiFi User Guide Figure 4-9 Settings Message Center: Disabled by default. Do not enable it unless you want to manually set the message center number. Message Center Number: When the Message Center is enabled, you can enter the ...
M7350 LTE-Advanced Mobile WiFi User Guide 4.4.1 Dial-up Dial-up Menu Figure 4-11 4.4.1.1. Dial-up Settings You can configure dial-up settings on this page. Dial-up Settings Figure 4-12 Mobile Data: It is enabled by default. You can disable it to prohibit Internet access.
Page 31
M7350 LTE-Advanced Mobile WiFi User Guide APN: Access Point Name, provided by your ISP. You need to set APN only after selecting the static APN type. You are recommended to keep the default value. Username/Password: Enter the username and password provided by your ISP. These ...
Page 32
M7350 LTE-Advanced Mobile WiFi User Guide 4.4.1.2. Network Mode You can configure Network Mode on this page. Network Mode Settings Figure 4-14 Network Mode: The device supports four modes of network connection - 4G Preferred, 4G Only, 3G Only, and 2G only. If your SIM card supports GSM, select 2G only; if your SIM card supports WCDMA, select 3G only;...
Page 33
M7350 LTE-Advanced Mobile WiFi User Guide Figure 4-15 PIN Management SIM Card Status: Shows the status of your SIM card. PIN Management: You can select whether to enable this function or not. Once the PIN code function is enabled, every time you start the device with this SIM card inserted, you need to enter the PIN code.
M7350 LTE-Advanced Mobile WiFi User Guide Figure 4-16 PIN Configuration - PUK Decode A PUK (PIN Unlocked Key), also known as Personal Unlock Code (PUC), is used in 3GPP mobile phones to reset a personal identification number (PIN) that has been lost or forgotten.
Page 35
M7350 LTE-Advanced Mobile WiFi User Guide 4.4.2.1. Basic Settings You can configure basic wireless settings on this page. Figure 4-18 Wireless Basic Settings Wireless Network Name (SSID): SSID is short for Service Set Identification, which helps you distinguish different wireless networks. The default SSID of this device is TP-LINK_M7350_XXXXXX (XXXXXX stand for the last 6 characters of the MAC address of it.).
Page 36
M7350 LTE-Advanced Mobile WiFi User Guide the best channel automatically. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. Wireless Mode: This field determines which Wi-Fi network protocol will be used. The ...
Page 37
M7350 LTE-Advanced Mobile WiFi User Guide Figure 4-19 WPS WPS Status: Enable or disable the WPS function here. WPS: Choose PBC or choose PIN and enter the PIN code to the root device, and then click Start. PBC: Push Button Configuration. You need to start WPS (by hardware or software) on ...
Page 38
M7350 LTE-Advanced Mobile WiFi User Guide Figure 4-20 Wireless MAC Filter Wireless MAC Filtering: Select to enable or disable the MAC filtering function of the device. The below settings will take effect only when you select Enable. Your MAC address: Displays the MAC address of your client currently wirelessly ...
M7350 LTE-Advanced Mobile WiFi User Guide Figure 4-21 Wireless Status ID: The index of the Wi-Fi client. Client Name: The name of the Wi-Fi client. MAC Address: The MAC address of the Wi-Fi client. IP Address: The IP address of the Wi-Fi client.
Page 40
M7350 LTE-Advanced Mobile WiFi User Guide Figure 4-22 DHCP Server DHCP Server: You can select to enable or disable the DHCP server. If you disable the server, you must have another DHCP server within your network or else you must configure the IP address of the computer manually.
M7350 LTE-Advanced Mobile WiFi User Guide 4.4.4 Data Settings You can configure data settings on this page. Figure 4-23 Data Settings Total/Monthly Used: Total/Monthly data used. You can click Correct and input the actual data amount to correct the data.
M7350 LTE-Advanced Mobile WiFi User Guide 4.4.5 Storage Sharing You can configure storage sharing on this page. Figure 4-24 Storage Sharing Access Mode: You can access the SD storage by USB or Wi-Fi. By USB: Connect the device with a USB cable to access the SD card directly.
M7350 LTE-Advanced Mobile WiFi User Guide 4.4.6 Device Figure 4-25 Device menu Under Device menu, you can do such configurations as restoring all the settings of the device to its factory defaults, rebooting the device, and checking some information about the device.
Page 44
M7350 LTE-Advanced Mobile WiFi User Guide New Version: This field displays the version number of the new firmware. You can click the version number to download the firmware or click Release Note to view the update details. Update via the local server: Update your firmware by using the update file that has been ...
Page 45
M7350 LTE-Advanced Mobile WiFi User Guide Figure 4-28 Account Management Old Username: The old username that is used to log in to the device. Old Password: The old password that is used to log in to the device. ...
Page 46
M7350 LTE-Advanced Mobile WiFi User Guide 4.4.6.4. Shutdown Figure 4-29 Shutdown Click Reboot to reboot the device. Click Power Off to shut down the device. 4.4.6.5. Time Settings Figure 4-30 Time Settings Time Zone: Select your local time zone. ...
Page 47
M7350 LTE-Advanced Mobile WiFi User Guide Time: Display your local time. Click Save to save your settings. 4.4.6.6. System log This page displays the device‘s information about system logs, including log ID, time, type, level, content, and debug log.
Page 48
M7350 LTE-Advanced Mobile WiFi User Guide Figure 4-32 Device Information Model: The model of the device. Firmware Version: The current firmware version. Hardware Version: The current hardware version. IMEI: International Mobile Equipment Identity. Composed of 15 digits, it is unique and thus ...
LTE-Advanced Mobile WiFi User Guide Appendix A: FAQ FAQ1. What should I do if I cannot log into the web-management page? Verify that your device is connecting to the M7350. Verify that you entered the correct IP address http://tplinkmifi.net or http://192.168.0.1.
Page 50
Tip 2: Press and hold the Reset button for about 5 seconds until the screen appears “Reboot”. Note: Once the M7350 is restored, all the current configurations will be lost and you may need to reconfigure it. FAQ4. What should I do if my Internet speed is slow? Tip 1: The 4G network may be in poor condition.
M7350 LTE-Advanced Mobile WiFi User Guide Appendix B: Configuring the PC In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows 7. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if needed.
Page 52
M7350 LTE-Advanced Mobile WiFi User Guide Click the right button, and Select Properties. In the prompt page that showed below, double click on the Internet Protocol Version 4 (TCP/IPv4). -44-...
Page 53
M7350 LTE-Advanced Mobile WiFi User Guide The following Internet Protocol Version 4 (TCP/IPv4) Properties window will display and the IP Address tab is open on this window by default. You have two ways to configure the TCP/IP protocol below: Setting IP address automatically...
Page 54
M7350 LTE-Advanced Mobile WiFi User Guide Setting IP address manually a. Select Use the following IP address radio button. And the following items available. b. If the Device's LAN IP address is 192.168.0.1, type IP address is 192.168.0.x (x is from 2 to 254), and Subnet mask is 255.255.255.0.
Page 55
M7350 LTE-Advanced Mobile WiFi User Guide Now click OK to keep your settings. -47-...
M7350 LTE-Advanced Mobile WiFi User Guide Appendix C: Specifications General Standards IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n 4G:FDD-LTE Network Type 3G: DC-HSPA+/HSPA/UMTS 2G: EDGE/GRPS/GSM Certification CE, RoHS Dimension 4.2 × 2.6 × 0.6 in. (106 × 66 × 16mm)
Page 57
M7350 LTE-Advanced Mobile WiFi User Guide Appendix D: Glossary 802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity, perhaps through coding schemes like Alamouti coding.