Preparing For Surround Sound; Speaker Settings - Kenwood KRF-V4550D Instruction Manual

Kenwood stereo receiver user manual
Hide thumbs Also See for KRF-V4550D:
Table of Contents

Advertisement

Preparing for surround sound

Speaker settings

16
To enable you to obtain optimum enjoyment from the receiver's
listening modes, make sure to complete the speaker settings
(subwoofer, front, center, and surround speakers) as described below.
1
Turn on the power to this receiver by pressing POWER and
ON/STANDBY key.
2
Select a speaker system.
1 Press the SET UP key to make the subwoofer setting indica-
tion (SUBW) appear.
SP
B
TI.VOL
L
C
R
CLIP
MUTE
LFE
SW
RDS EON
PTY
LS
S
RS
TP
TA
NEWS
2 Use the MULTI CONTROL to select the appropriate subwoofer
setting.
1 SUBW YES: A subwoofer is connected to the receiver.
2 SUBW NO: No subwoofer is connected to the receiver.
• The initial setting is "SUBW YES".
• When the setting "SUBW NO" is selected, the front speakers
automatically are set to "FRNT LRG" and the procedure skips to
step 5.
• When subwoofer output sound is required select "FRNT NML".
3 Press the SET UP key to accept the setting.
• The front speakers setting indication (FRNT) appears.
SP
B
TI.VOL
L
C
R
CLIP
MUTE
LFE
SW
RDS EON
PTY
LS
S
RS
TP
TA
NEWS
4 Use the MULTI CONTROL to select the appropriate front
speakers setting.
1 FRNT NML (normal): Average size front speakers are
2 FRNT LRG (large):
5 Press the SET UP key to accept the setting.
• The center speaker setting indication (CNTR) appears.
FM
AUTO SOUND
DIGITAL
AUTO
AM
PRO LOGIC
S.DIRECT
MEMO
ST.
MHz
3
STEREO
MONITOR
TUNED
kHz
DOWN MIX
DSP
FM
AUTO SOUND
DIGITAL
AUTO
AM
PRO LOGIC
S.DIRECT
MEMO
MHz
3
STEREO
MONITOR
ST.
kHz
DOWN MIX
DSP
TUNED
connected to the receiver.
Large front speakers are
connected to the receiver.
6 Use the MULTI CONTROL to select the appropriate center
speaker setting.
If you selected "LRG" as the front speakers setting.
1 CNTR LRG (large):
2 CNTR NML (normal): An average size center speaker is
3 CNTR NO:
If you selected "NML" as the front speakers setting.
1 CNTR YES:
A center speaker is connected to the
receiver.
2 CNTR NO:
No center speaker is connected to the
receiver.
7 Press the SET UP key to accept the setting.
• The surround speaker setting indication (SURR) appears.
8 Use the MULTI CONTROL to select the appropriate surround
speaker setting.
If you selected "LRG" as the center speaker setting.
1 SURR LRG (large):
2 SURR NML (normal): Average size surround speakers are
3 SURR NO:
If you selected other than "LRG" as the center speaker setting.
1 SURR YES:
Surround speakers are connected to the re-
ceiver.
2 SURR NO:
No surround speakers are connected to the
receiver.
9 Press the SET UP key to accept the setting.
• The receiver enters the speaker volume level adjustment mode.
• In steps 3 and 4, indications appear only for the selected
channels of the speakers that require adjusting.
3
Adjust the volume levels for the speakers.
Sit in your normal listening position and listen to the test tone. Adjust
the volume levels for the speakers until all speakers seem to be
equally loud.
1 Use the MULTI CONTROL to adjust the volume when the test
tone is being output from the speaker channel to be adjusted.
The channel indication blinks while the test tone is being output.
SP
B
TI.VOL
L
C
R
CLIP
MUTE
LFE
SW
RDS EON
PTY
LS
S
RS
TP
TA
NEWS
The test tone issues from the speakers for 2 seconds at a time
in the following sequence:
Lch = Cch = Rch = RS = LS = SW = Lch
• If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
changed.
• If the speaker setting selects are changed, the speaker level
settings are reset.
2 Press the SET UP key.
• The receiver enters the mode for inputting the distance to the
speakers.
A large center speaker is connected
to the receiver.
connected to the receiver.
No center speaker is connected to
the receiver.
Large surround speakers are con-
nected to the receiver.
connected to the receiver.
No surround speakers are connected
to the receiver.
FM
AUTO SOUND
DIGITAL
AUTO
AM
PRO LOGIC
S.DIRECT
MEMO
MHz
3
STEREO
MONITOR
ST.
kHz
DOWN MIX
DSP
TUNED
Continued to next page

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents