1. Manuals
  2. Brands
  3. TP-Link Manuals
  4. Network Router
  5. TD-8817B
  6. User manual

TP-Link TD-8817B User Manual

Adsl2+ modem router
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
TD-8817B
ADSL2+ Modem Router
Rev:2.0.1
1910010487

Advertisement

Table of Contents
loading

Related Manuals for TP-Link TD-8817B

Summary of Contents for TP-Link TD-8817B

  • Page 1 TD-8817B ADSL2+ Modem Router Rev:2.0.1 1910010487...
  • Page 2 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.

  • Page 3: Fcc Statement

    FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications.

  • Page 4: Table Of Contents

    CONTENTS Package Contents ....................1 Chapter 1. Introduction ..................2 Product Overview ...................... 2 Main Features ......................2 Conventions ......................3 Chapter 2. Hardware Installation ................. 4 The Front Panel ......................4 The Back Panel......................5 Installation Environment .................... 5 Hardware installation procedures................
  • Page 5 4.5.6 CWMP ..........................47 Maintenance......................47 4.6.1 Administration.........................48 4.6.2 Time Zone ........................48 4.6.3 Firmware.........................50 4.6.4 SysRestart........................52 4.6.5 Diagnostic........................52 Help......................... 53 Appendix A: Specification..................54...

  • Page 6: Package Contents

    Package Contents The following items should be found in your package: One TD-8817B ADSL2+ Modem Router One Power Adapter for TD-8817B ADSL2+ Modem Router Quick Installation Guide One RJ45 cable One USB cable Two RJ11 cables One ADSL splitter One Resource CD , including:...

  • Page 7: Chapter 1. Introduction

    The device is designed to provide a simple and cost-effective ADSL Internet connection for a private Ethernet network. TD-8817B connects to an Ethernet LAN or computers via standard Ethernet ports. The ADSL connection is made using ordinary telephone line with standard connectors. Multiple workstations can be networked and connected to the Internet using a single Wide Area Network (WAN) interface and single global IP address.

  • Page 8: Conventions

    Supports system log and flow Statistics. Supports firmware upgrade and Web management. 1.3 Conventions The Router or device mentioned in this User Guide stands for TD-8817B without any explanations. Parameters provided in the pictures are just references for setting up the product, which may...

  • Page 9: Chapter 2. Hardware Installation

    TD-8817B ADSL2+ Modem Router User Guide Chapter 2. Hardware Installation 2.1 The Front Panel Figure 2-1 The LEDs are located on the front panel, they indicate the device’s working status. For details, please refer to LED Explanation. LED Explanation: Status Indication Power is on.

  • Page 10: The Back Panel

    TD-8817B ADSL2+ Modem Router User Guide 2.2 The Back Panel Figure 2-2 ON/OFF: The switch for the power. POWER: The Power plug is where you will connect the power adapter. LAN: Through the port, you can connect the Router to your PC or the other Ethernet network devices.
  • Page 11 TD-8817B ADSL2+ Modem Router User Guide Last Step: Check the line connection to see if everything is ready. Power up finally. Figure 2-3...

  • Page 12: Chapter 3. Quick Installation Guide

    Chapter 3. Quick Installation Guide 3.1 Configure PC After you directly connect your PC to the TD-8817B or connect your adapter to a Hub/Switch which has connected to the Router, you need to configure your PC’s IP address. Follow the steps below to configure it.
  • Page 13 TD-8817B ADSL2+ Modem Router User Guide Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties button. Figure 3-3...
  • Page 14 TD-8817B ADSL2+ Modem Router User Guide Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK. Figure 3-4 Note: You can configure the PC to get an IP address automatically, select “Obtain an IP address automatically” and “Obtain DNS server address automatically” in the screen above.

  • Page 15: Usb Configuration

    CD into your CD-ROM drive. The autorun.exe will automatically run and click Browse CD to read the files on the CD. Click the file TD-8817B>USB Driver and select the USB driver type according to the operating system of your computer to start installation.
  • Page 16 TD-8817B ADSL2+ Modem Router User Guide Figure 3-7 Step 3: You will see Figure 3-8 as follow, please wait a moment. Figure 3-8 Step 4: After that, you will see Figure 3-9. Click Finish to complete the installation.

  • Page 17: Login

    TD-8817B ADSL2+ Modem Router User Guide Figure 3-9 Note: All of the above settings are under windows XP. If you want to pull out the USB device you must disconnect the network of USB first. In the Vista operating system, maybe the “Unknown Device” screen will pop up when you insert the USB cable of the Router to a computer, please just unplug the USB cable and try again.
  • Page 18 TD-8817B ADSL2+ Modem Router User Guide Figure 3-10 Step 1: Select the Quick Start tab, then click RUN WIZARD, and you will see Figure 3-11. Click the NEXT button. Figure 3-11 Step 2: Configure the time for the Router, and then click the NEXT button.
  • Page 19 TD-8817B ADSL2+ Modem Router User Guide Figure 3-13 Step 4: Configure the following options provided by your ISP: Username, Password, VPI, VCI and Connection Type. Then click NEXT. Figure 3-14 Step 5: Click NEXT to finish the Quick Start. Figure 3-15...

  • Page 20: Chapter 4. Software Configuration

    TD-8817B ADSL2+ Modem Router User Guide Chapter 4. Software Configuration This User Guide recommends using the “Quick Installation Guide” for first-time installation. For advanced users, if you want to know more about this device and make use of its functions adequately, maybe you will get help from this chapter to configure the advanced settings through the Web-based Utility.

  • Page 21: System Log

    TD-8817B ADSL2+ Modem Router User Guide Figure 4-2 4.1.2 System Log Choose “Status→System Log” menu, and you will be able to query the logs of the Router.

  • Page 22: Statistics

    TD-8817B ADSL2+ Modem Router User Guide Figure 4-3 The Router can keep logs of all traffic. You can query the logs to find what happened to the Router. Click the CLEAR LOG button to clear the logs. Click the SAVE LOG button to save the logs.
  • Page 23 TD-8817B ADSL2+ Modem Router User Guide Figure 4-4 Interface: You can select Ethernet and ADSL to view the corresponding network traffic over different ports. Select Ethernet, and you will see the statistics table as below. Statistics Table: Transmit Frames The frames transmitted over the Ethernet port.

  • Page 24: Quick Start

    TD-8817B ADSL2+ Modem Router User Guide Select ADSL, and you will see the statistics table as below. Statistics Table: Transmit total PDUs The total PDUs transmitted over the ADSL port. Transmit The total errors occurred over the ADSL port when data...
  • Page 25 TD-8817B ADSL2+ Modem Router User Guide Figure 4-6 ATM VC: ATM settings are used to connect to your ISP. Your ISP provides VPI (Virtual Path Identifier), VCI (Virtual Channel Identifier) settings to you. In this Device, you can totally setup 8 VCs on different encapsulations, if you apply 8 different virtual circuits from your ISP.
  • Page 26 TD-8817B ADSL2+ Modem Router User Guide • VPI: Identifies the virtual path between endpoints in an ATM network. The valid range is from 0 to 255. Please input the value provided by your ISP. • VCI: Identifies the virtual channel endpoints in an ATM network. The valid range is from 32 to 65535 (1 to 31 is reserved for well-known protocols).
  • Page 27 TD-8817B ADSL2+ Modem Router User Guide Dynamic Route: Select this option to specify the RIP (Routing Information protocol) version for WAN interface, including RIP1, RIP2-B and RIP2-M. RIP2-B and RIP2-M are both sent in RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast format.
  • Page 28 TD-8817B ADSL2+ Modem Router User Guide PPPoA/PPPoE Select this option if your ISP requires you to use a PPPoE connection. This option is typically used for DSL services. Select Dynamic PPPoE to obtain an IP address automatically for your PPPoE connection. Select Static PPPoE to use a static IP address for your PPPoE connection.

  • Page 29: Lan

    TD-8817B ADSL2+ Modem Router User Guide Connection: For PPPoE/PPPoA connection, you can select Always on or Connect on-Demand or Connect Manually. Connect on demand is dependent on the traffic. If there is no traffic (or Idle) for a pre-specified period of time), the connection will tear down automatically.
  • Page 30 TD-8817B ADSL2+ Modem Router User Guide Figure 4-11 Router Local IP: These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed.
  • Page 31 TD-8817B ADSL2+ Modem Router User Guide DHCP Server: Select Enabled, then you will see the screen below (shown in Figure 4-12). The Router will work as a DHCP Server, it becomes the default gateway for DHCP client connected to it. DHCP stands for Dynamic Host Control Protocol. The DHCP Server gives out IP addresses when a device is booting up and request an IP address to be logged on to the network.

  • Page 32: Advanced Setup

    TD-8817B ADSL2+ Modem Router User Guide DHCP Relay: Select Relay, then you will see the next screen (shown in Figure 4-13), the Router will work as a DHCP Relay. A DHCP relay is a computer that forwards DHCP data between computers that request IP addresses and the DHCP server that assigns the addresses.

  • Page 33: Routing

    TD-8817B ADSL2+ Modem Router User Guide Firewall: Select this option can automatically detect and block Denial of Service (DoS) attacks, such as Ping of Death, SYN Flood, Port Scan and Land Attack. SPI: If you enable SPI, all traffics initiated from WAN would be blocked, including DMZ, Virtual Server, and ACL WAN side.

  • Page 34: Nat

    TD-8817B ADSL2+ Modem Router User Guide Announced in RIP: This parameter determines if the ADSL router will include the route to this remote node in its RIP broadcasts. If set to Yes, the route to this remote node will be propagated to other hosts through RIP broadcasts.
  • Page 35 TD-8817B ADSL2+ Modem Router User Guide Figure 4-19 DMZ Host IP Address: Enter the specified IP Address for DMZ host on the LAN side. 4.4.3.2. Virtual Server Choose “Advanced Setup→NAT→Virtual Server” in Figure 4-18, you can configure the Virtual Server in the next screen.
  • Page 36 TD-8817B ADSL2+ Modem Router User Guide Note: For VCs with single IP, select Single; For VCs with multiple IPs, select Multiple for the option. Step 2: Select the Rule index for the rule as shown in Figure 4-20. Step 3: Select the application you want from drop-down list, then the protocol and port number will be added to the corresponding field automatically, you only need to configure the IP address for the virtual server;...

  • Page 37: Qos

    TD-8817B ADSL2+ Modem Router User Guide Figure 4-22 Rule Index: Select the Address Mapping Rule index for this VC. You can specify 8 rules in maximum. Rule Type: There are four types, one-to-one, Many-to-One, Many-to-Many Overload and Many-to-Many No-overload. Local Start & End IP: Enter the local IP Address you plan to mapped to. Local Start IP is the starting local IP address and Local End IP is the ending local IP address.
  • Page 38 TD-8817B ADSL2+ Modem Router User Guide incoming packets, QoS determines which queue the packets enter, based priority. This is useful when there are certain types of data you want to give higher priority, such as voice data packets give higher priority than Web data packets. This option will provide better service of selected network traffic over various technologies.

  • Page 39: Vlan

    TD-8817B ADSL2+ Modem Router User Guide • Destination MAC & IP & Mask & Port Range: Enter the IP information about the Destination host for the rule. • Source MAC & IP & Mask & Port Range: Enter the IP information about the Source host for the rule.
  • Page 40 TD-8817B ADSL2+ Modem Router User Guide Figure 4-24 Assign VLAN PVID for each Interface Click Assign VLAN PVID for each Interface in Figure 4-24, you can assign the PVID for each interface in the next screen (shown in Figure 4-25).

  • Page 41: Adsl

    TD-8817B ADSL2+ Modem Router User Guide Figure 4-26 VLAN Index: Select the VLAN index for this VC. You can specify 8 groups in maximum. VLAN ID: This indicates the VLAN group. ATM VCs: Select the ATM VCs as members of VLAN, and if you leave the Tagged blank, the tag in frames will be deleted when transmitted from the VC.

  • Page 42: Access Management

    TD-8817B ADSL2+ Modem Router User Guide Figure 4-27 ADSL Mode: Select the ADSL operation mode which your ADSL connection uses. ADSL Type: Select the ADSL operation type which your ADSL connection uses. 4.5 Access Management Choose “Access Management”, you can see the next submenus: Figure 4-28 Click any of them, and you will be able to configure the corresponding function.

  • Page 43: Filter

    TD-8817B ADSL2+ Modem Router User Guide Figure 4-29 ACL: If Activated, the IP addresses which are contained in the Access Control List can access to the Router. If Deactivated, all IP addresses can access to the Router. ACL Rule Index: Select the ACL rule index for the entry.
  • Page 44 TD-8817B ADSL2+ Modem Router User Guide Figure 4-30 Filter Type Selection: Select the filter type for the configuration below. IP/MAC Filter Set Index: Select the Set index for the IP Filter entry. This index can match with six IP / MAC Filter Rule Indexes.
  • Page 45 TD-8817B ADSL2+ Modem Router User Guide Note: Incoming means that IP traffic which is coming into the router, and the Outgoing means that IP traffic which is going out the router. IP/MAC Filter Rule Index: Select the Rule index for the IP Filter entry.
  • Page 46 TD-8817B ADSL2+ Modem Router User Guide Note: If you want to make the rule take effect, please select Yes to active the rule. Step 3: Enter the “Source IP Address”, “Destination IP Address”, “Subnet Mask” and “Port Number” in the corresponding field.
  • Page 47 TD-8817B ADSL2+ Modem Router User Guide 4.5.2.2. MAC Filter Select IP/Mac Filter as the Filter type, and select MAC as the Rule type (shown in Figure 4-31), then you can configure the filter rules based on MAC address. Figure 4-31 Rule Type: Select MAC for the MAC Filter rule.
  • Page 48 TD-8817B ADSL2+ Modem Router User Guide , Then you can configure the specific rule for the example. Step 2: Select the IP/MAC Filter Set Index and IP/MAC Filter Rule Index for the rule, then select the Interface “PVC0”, and select the Direction “Outgoing” for the first rule.
  • Page 49 TD-8817B ADSL2+ Modem Router User Guide Figure 4-32 Filter Type Selection: Select the Application Filter for the next configuration. Application Filter: Activate or deactivate the function. ICQ & MSN & YMSG & Real Audio/Video: Select Allow or Deny for these applications. If you select Allow, the Router will accept the application;...

  • Page 50: Snmp

    TD-8817B ADSL2+ Modem Router User Guide Filter Type Selection: Select the URL Filter for the next configuration. Active: Select “Yes” to make the rule to take effect. URL Index: Select the index for the URL Filter entry. URL: Enter the URL for this URL Filter.

  • Page 51: Ddns

    TD-8817B ADSL2+ Modem Router User Guide use. UPnP broadcasts are only allowed on the LAN. Figure 4-35 UPnP: Activate or Deactivate the UPnP function. Only when the function is activated, can the UPnP take effect. Auto-Configure: If you activate the function, then the UPnP network devices can automatically configure network addressing, announce their presence in the network to other UPnP devices and enable exchange of simple product and service descriptions.

  • Page 52: Cwmp

    TD-8817B ADSL2+ Modem Router User Guide Wildcard support: Select the option to use Wildcard function 4.5.6 CWMP Choose “Access Management→CWMP”, you can configure the CWMP function in the screen (shown in Figure 4-37). The router offers CWMP feature. The function supports TR-069 protocol which collects information, diagnoses the devices and configures the devices automatically via ACS (Auto-Configuration Server).

  • Page 53: Administration

    TD-8817B ADSL2+ Modem Router User Guide Figure 4-38 Click any of them, and you will be able to configure the corresponding function. 4.6.1 Administration Choose “Maintenance→Administration”, you can set new password for admin in the screen (shown in Figure 4-39).
  • Page 54 TD-8817B ADSL2+ Modem Router User Guide Figure 4-40 Note: The ADSL Router built-in some NTP Servers, when the Router connects to the Internet, the Router will get the system time automatically from the NTP Server. You can also configure the NTP Server address manually, and then the Router will get the time from the specific Server firstly.

  • Page 55: Firmware

    TD-8817B ADSL2+ Modem Router User Guide Figure 4-42 4.6.3 Firmware Choose “Maintenance→Firmware”, you can upgrade the firmware of the Router in the screen (shown in Figure 4-43). Make sure the firmware or romfile you want to use is on the local hard drive of the computer.
  • Page 56 TD-8817B ADSL2+ Modem Router User Guide Note: New firmware versions are posted at www.tp-link.com and can be downloaded for free. If the router is not experiencing difficulties, there is no need to download a more recent firmware version, unless the version has a new feature that you want to use.

  • Page 57: Sysrestart

    TD-8817B ADSL2+ Modem Router User Guide To restore the Router’s settings: Step 1: Click the Browse button to locate the update file for the device, or enter the exact path in “New Romfile Location” field. Step 2: Click the UPGRADE button to complete.

  • Page 58: Help

    TD-8817B ADSL2+ Modem Router User Guide 4.7 Help Choose “Help”, you can view the help information for configuration of any function. Figure 4-48 Note: Click the tab, and you will be able to get the corresponding information.

  • Page 59: Appendix A: Specification

    TD-8817B ADSL2+ Modem Router User Guide Appendix A: Specification General ANSI T1.413, ITU G.992.1, ITU G.992.2, ITU G.992.3, ITU G.992.5 Standards and Protocols IEEE 802.3, IEEE 802.3u, TCP/IP, PPPoA , PPPoE, SNTP, HTTP, DHCP, ICMP, NAT,CWMP Safety & Emission FCC, CE 1 10/100M Auto-Negotiation RJ45 port（Auto MDI/MDIX)

Table of Contents