Toshiba e-studio200l Service Manual page 704

10.3 Connector Table (e-STUDIO200L/230/230L/280/280S)
CN301 PWA-F-LGC (CN301) <-> COIN CONTROLLER (OPTION)/ CN308 PWA-F-LGC (CN308) <-> PS-HVT (CN720)/THMS-C-HTR,
COPY KEY CARD (OPTION) THMS-S-HTR, THMS-EDG-HTR, EXT-SNR
Pin No Symbol Name Active Pin No Symbol
A1 +24VD2 +24 V - A1 HVCLK-0A
A2 CTRON Total counter ON signal - A2 HVSDWN-1A
A3 CTRCNT Copy key card connection detection signal L A3 HVSAV-1A
A4 M/C RUN M/C run signal L A4 HVTSP-0A
A5 EXTCTR Exit sensor ON signal L A5 HVTGB-0A
A6 PG Power ground - A6 HVTVR-1A
Black and white mode counter ON signal and A7 HVTT-0A
A7 BKCTR -
CST-CTR signal
A8 HVAVR-1A
A8 MNCTR Mono-color mode counter ON signal -
Full color mode counter ON signal and reverse A9 HVTAC-0A
B1 FLCTR -
side counter signal
A10 HVDVR-1A
B2 SG Signal ground -
B3 TSIZE3 Paper size signal-3 - A11 HVMVR-1A
B4 TSIZE2 Paper size signal-2 -
A12 HVTM-0A
B5 TSIZE1 Paper size signal-1 -
B6 TSIZE0 Paper size signal-0 -
A13 SG
B7 +5.1VB +5.1 V - A14 +24VD2
B8 CTRCNT2 Copy key card /Coin counter judgment signal - B1 FUSSW-1A
B2 MTH+-1A
B3 MTH--1A
CN302 PWA-F-LGC (CN302) <-> KEY COPY COUNTER (OPTION)
B4 STH+-1A
Pin No Symbol Name Active
B5 STH--1A
1 NC Not connected -
B6 ETH+-1A
2 SG Signal ground
B7 ETH--1A
Key copy counter/Copy key card connection
3 KCTRC-0 L B8 +5.1VSW
detection signal
B9 SG
4 +24VD2 +24 V -
B10 EXTSW-1
5 KCTRO-0 Key copy counter ON signal -
B11 +5.1VB
6 NC Not connected -
B12 NC
B13 NC
CN303 PWA-F-LGC (CN303) <-> LP-ERS, ATTNR-SNR, THMS-DRM, B14 NC
MAIN-SW (RESET), TEMP/HUMI-SNR,
CN310 PWA-F-LGC (CN310) <-> PFP (OPTION)/LCF (OPTION)
FRNT-COV-SW (e-STUDIO200L)
Pin No Symbol
Pin No Symbol Name Active
A1 CLKC-1A
A1 ATSCNT-1 PU connection detection signal L
A2 CLKB-1A
A2 ERSLP-0A Exposure lamp drive signal -
A3 SCSWC-0A
A3 +24VD1 +24 V -
A4 DRV7-1A
A4 PG Power ground -
A5 DRV6-1A
A5 ATS-1A Auto-toner sensor detection signal Analog
A6 DRV5-1A
A6 +24VD1 +24 V (Auto-toner sensor) -
A7 DRV4-1A
A7 ATSVR-1A Auto-toner sensor detection signal Analog
A8 DRV3-1A
A8 DRTH-1 Drum thermistor detection signal Analog
A9 DRV2-1A
A9 SG Signal ground -
A10 DRV1-1A
A10 SG Signal ground -
A11 DRV0-1A
B1 RSTSW-0A Reset signal to the main switch H
A12 PFRST-0
B2 +24VD1 +24 V -
A13 +5.1VB
B3 +5.1VB +5.1 V -
A14 SG
B4 HMS-1A Humidity sensor signal Analog
A15 +24VD1
B5 SG Signal ground -
A16 +24VD1
B6 TEMP-1 Temperature sensor signal Analog
B1 PG
B7 FCOVSW-1 Front cover opening/closing switch signal -
B2 PG
B8 SG Signal ground -
B3 SIZE0-0A
B9 NC Not connected -
B4 SIZE1-0A
B10 NC Not connected -
B5 SIZE2-0A
B6 SIZE3-0A
CN303 PWA-F-LGC (CN303) <-> LP-ERS, ATTNR-SNR, THMS-DRM,
B7 RETS0-0A
MAIN-SW (RESET), TEMP/HUMI-SNR, B8 RETS1-0A
B9 RETS2-0A
FRNT-COV-SW (e-STUDIO230/230L)
B10 RETS3-0A
Pin No Symbol Name Active
B11 RETS4-0A
A1 ATSCNT-1 PU connection detection signal L
B12 RETS5-0A
A2 ERSLP-0A Exposure lamp drive signal -
B13 RETS6-0A
A3 +24VD1 +24 V -
B14 RETS7-0A
A4 PG Power ground -
B15 SCSWB-0A
A5 ATS-1A Auto-toner sensor detection signal Analog
B16 LCCNT-0
A6 +24VD1 +24 V (Auto-toner sensor) -
A7 ATSVR-1A Auto-toner sensor detection signal Analog
CN312 PWA-F-LGC (CN312) <-> M/DC-POL
A8 DRTH-1 Drum thermistor detection signal Analog
A9 SG Signal ground - Pin No Symbol
A10 SG Signal ground - 1 POMCK-0
A11 NC Not connected - 2 POMOL-0
B1 NC Not connected -
3 POMON-0
B2 RSTSW-0A Reset signal to the main switch H
B3 +24VD1 +24 V -
4 PG
B4 +5.1VB +5.1 V -
5 +24VD1
B5 HMS-1A Humidity sensor signal Analog
B6 SG Signal ground -
CN313 PWA-F-LGC (CN313) <-> PWA-F-LRL (CN204)
B7 TEMP-1 Temperature sensor signal Analog
Pin No Symbol
B8 FCOVSW-1 Front cover opening/closing switch signal -
1 SG
B9 SG Signal ground -
2 +5VD
B10 NC Not connected -
3 +5VD
B11 NC Not connected -
4 SG
5 WRLVL-1
CN303 PWA-F-LGC (CN303) <-> LP-ERS, ATTNR-SNR, THMS-DRM,
6 SG
MAIN-SW (RESET), TEMP/HUMI-SNR, 7 BDIN-1
8 SG
FRNT-COV-SW (e-STUDIO280/280S)
9 PIDT-1
Pin No Symbol Name Active
10 PIDT-0
A1 ATSCNT-1 PU connection detection signal L
11 SG
A2 ERSLP-0A Exposure lamp drive signal -
12 WRAPC-0
A3 +24VD1 +24 V -
13 +5.1VB
A4 PG Power ground -
14 SHDWM-1
A5 ATS-1A Auto-toner sensor detection signal Analog
15 SG
A6 +24VD1 +24 V (Auto-toner sensor) -
16 +5.1VD
A7 ATSVR-1A Auto-toner sensor detection signal Analog
17 +5.1VD
A8 DRTH-1 Drum thermistor detection signal Analog
18 SG
A9 SG Signal ground -
A10 SG Signal ground -
CN316 PWA-F-LGC (CN316) <-> DOWNLOAD JIG (LGC)
A11 NC Not connected -
Pin No Symbol
A12 NC Not connected -
B1 CPSW2-0 Not used - 1 D[0]
B2 SG Signal ground - 2 D[2]
B3 RSTSW-0A Reset signal to the main switch H 3 D[4]
B4 +24VD1 +24 V - 4 D[6]
B5 +5.1VB +5.1 V - 5 RD-0
B6 HMS-1A Humidity sensor signal Analog 6 A[0]
B7 SG Signal ground - 7 A[2]
B8 TEMP-1 Temperature sensor signal Analog 8 A[4]
B9 FCOVSW-1 Front cover opening/closing switch signal L 9 A[6]
B10 SG Signal ground - 10 A[8]
B11 NC Not connected - 11 A[10]
B12 NC Not connected - 12 A[12]
13 A[14]
14 A[16]
CN304 PWA-F-LGC (CN304) <-> PWA-F-ADU (CN211, 212), ADU-CLT,
15 A[18]
SID-COV-SNR, SFB-SIZE-SNR, SFB-SNR, SFB-FEED-CLT,
16 SG
17 SG
SFB-SOL, SFB-FEED-SNR-2
18 D[1]
Pin No Symbol Name Active
19 D[3]
A1 ADM1D-0A ADU motor drive signal-D -
20 D[5]
A2 ADM1B-0A ADU motor drive signal-B -
21 D[7]
A3 ADM1C-0A ADU motor drive signal-C -
22 CS2-0
A4 ADM1A-0A ADU motor drive signal-A -
23 A[1]
A5 ADUVR-1 ADU motor current control reference voltage -
24 A[3]
A6 ADTR2-1 ADU exit sensor detection signal -
25 A[5]
A7 5.1VB +5.1 V -
26 A[7]
A8 SG Signal ground -
27 A[9]
A9 ADCNT-1 ADU connection detection signal L
28 A[11]
A10 ADTR1-1 ADU entrance sensor detection signal L
29 A[13]
A11 ADCOV-1 ADU opening/closing switch detection signal -
30 A[15]
A12 +24VD2 +24 V -
31 A[17]
A13 ADUCL-0A ADU clutch drive signal L
32 ROMDT-0
A14 SG Signal ground L
33 +5.1VB
A15 CSTCSW-1 Side cover opening/closing sensor detection signal L
34 LED-0A
A16 +5.1VB +5.1 V -
A17 NC Not connected -
A18 NC Not connected - CN317 PWA-F-LGC (CN317) <-> IPC (OPTION)
A19 NC Not connected -
Pin No Symbol
A20 NC Not connected -
1 SG
B1 SFSZ3-0 Not used -
2 +5.1VB
B2 SG Signal ground -
3 AD0
B3 SG Signal ground -
4 AD2
B4 SFSZ0-0 Bypass paper size detection signal-1 -
5 AD4
B5 SFSZ1-0 Bypass paper size detection signal-2 -
6 AD6
B6 SFSZ2-0 Bypass paper size detection signal-3 -
7 I/O0
B7 SG Signal ground -
8 I/O2
B8 SFBEMP-1 Bypass paper detection signal -
9 I/O4
B9 5.1VB +5.1 V -
10 I/O6
B10 +24VD2 +24 V -
11 SG
B11 SFBCL1-0 Bypass feed clutch drive signal L
12 WE
B12 +24VD2 +24 V -
13 CSIP2-0A
B13 SFBCL2-0 Bypass pickup solenoid drive signal -
14 +5.1VB
B14 SG Signal ground -
15 IPCSW-0
B15 SFBTRY-1 Not used -
16 SG
B16 +5.1VB +5.1 V -
17 +5.1VB
B17 SG Signal ground -
18 AD1
B18 2NDFED-1 2nd transport sensor detection signal -
19 AD3
B19 +5.1VB +5.1 V -
20 AD5
B20 SFBCNT-1 Bypass unit connection detection signal -
21 AD7
22 I/O1
CN305 PWA-F-LGC (CN305) <-> FEED-SNR-1, RGST-SNR, TR-COV- 23 I/O3
24 I/O5
SW, TNR-SW, AUG-LOCK-SW, TNR-MOT, MAIN-MOT,
25 I/O7
REAR-FAN-MOT, MID-FAN-MOT, RGST, CLT.TR-U-CLT,
26 SG
27 OE
TR-M-CLT
28 IPRST-0A
Pin No Symbol Name Active
29 +5.1VB
A1 SG Signal ground
30 SG
A2 1STFEED-1 1st transport sensor detection signal
A3 +5.1VB +5.1 V
A4 SG Signal ground CN100 PWA-F-SYS (CN100) <-> DOWNLOAD JIG (SYS)
A5 PSTPSW-1 Registration sensor detection signal -
Pin No Symbol
A6 +5.1VB +5.1 V -
1 DATA0
A7 SG Signal ground -
2 DATA2
A8 SDCSW-1 Transfer cover opening/closing detection signal -
3 DATA4
A9 NC Not connected - 4 DATA6
A10 TNRSW-1 Toner cartridge installation detection signal - 5 DATA8
A11 SG Signal ground - 6 DATA10
A12 TNRFULL-1 Cleaner auger lock detection signal - 7 DATA12
A13 SG Signal ground - 8 DATA14
A14 TNRMT-0A Toner motor drive signal - 9 A21
A15 TNRMT-1A Toner motor drive signal -
10 A19
A16 NC Not connected -
11 A17
A17 NC Not connected -
12 A15
B1 RGTCL-0A Registration roller clutch drive signal -
13 A13
B2 +24VD1 +24 V -
14 A11
B3 1STCLL-0A Middle transport clutch drive signal -
15 A09
B4 +24VD1 +24 V -
16 A07
B5 1STCLH-0A Upper transport clutch drive signal -
17 A05
B6 +24VD1 +24 V -
18 A03
L: Braking
19 RDX
B7 MAMBK-0A Main motor brake signal
H: Normal 20 CS7-A
B8 MAMPL-1 Main motor PLL signal L: Normal 21 CS7-B
L: CW, 22 +3.3VA
B9 MAMCW-0A Main motor rotational direction signal
23 +3.3VA
H: CCW
24 SG
B10 MAMCK-1 Main motor reference clock signal -
25 SG
L: ON,
B11 MAMON-0A Main motor ON/OFF signal
26 DATA1
H: OFF
27 DATA3
B12 SG Signal ground -
28 DATA5
B13 +5.1VB +5.1 V -
29 DATA7
B14 +24VD1 +24 V -
30 DATA9
B15 PWRFN-0A Internal cooling fan2 motor drive signal -
31 DATA11
B16 +24VD1 +24 V -
32 DATA13
B17 CLNFN-0A Internal cooling fan1 motor drive signal
33 DATA15
34 A20
CN306 PWA-F-LGC (CN306) <-> EXIT-MOT, EXIT-FAN-MOT, JOB
35 A18
SEPARATOR (OPTION)/OFFSET TRAY (OPTION)/ 36 A16
37 A14
BRIDGE UNIT (OPTION)
38 A12
Pin No Symbol Name Active
39 A10
A1 +24VD2 +24 V
40 A08
A2 EXTMA-0A Exit motor drive signal-A
41 A06
A3 EXTMB-0A Exit motor drive signal-B
42 A04
A4 EXTMC-0A Exit motor drive signal-C
43 A02
A5 EXTMD-0A Exit motor drive signal-D
44 DWNLED
A6 +24VD2 +24 V -
45 /CS0
A7 +24VD2 +24 V -
46 +3.3VA
A8 VCMFN-0 Exhaust fan motor drive signal -
47 RMSL
A9 NC Not connected -
48 /WRX
A10 NC Not connected -
49 SG
A11 NC Not connected -
50 SG
A12 NC Not connected -
A13 NC Not connected -
CN101 PWA-F-SYS (CN101) <-> FAX (CN701) (OPTION)
A14 NC Not connected -
A15 NC Not connected - Pin No Symbol
A16 NC Not connected - 1 +5.1VB
A17 NC Not connected - 2 DA1
A18 NC Not connected - 3 +5.1VB
B1 RLC2S-1 JSP/OCT unit exit sensor signal - 4 DD0
5 +5.1VB
B2 +5.1VB +5.1 V -
6 DD3
JSP: lower stack sensor detection signal /
B3 RLHSW-1 -
OCT: stack sensor detection signal 7 +5.1VB
B4 SG Signal ground - 8 DD6
B5 JSPSW-0 JSP/OCT judgment signal L 9 +5.1VB
B6 RLCNT-0 JSP/OCT judgment signal - 10 DD9
11 SG
L: OCT,
B7 OPCHK1-1 JSP/OCT judgment signal
12 DD12
H: JSP
13 SG
B8 RLCSW-1 JSP/OCT cover opening/closing detection signal L
14 SG
JSP: paper jam sensor detection signal /
B9 RLTRS-1 - 15 SG
OCT: paper feed sensor detection signal
16 SG
JSP: upper stack sensor detection signal /
B10 JFSL2OH-1 - 17 SG
OCT: separate sensor detection signal
18 SG
B11 GASOL-0A JSP/OCT gate solenoid driving signal -
19 +3.3VB
B12 +24VD2 +24 V -
20 INTRQ
B13 PG Power ground -
21 +3.3VB
B14 OFFSET1 OCT motor drive signal-1 -
22 +5.1VB
B15 OFFSET2 OCT motor drive signal-2 -
23 -12VB
B16 NC Not connected -
24 SG
B17 NC Not connected -
25 +12VB
B18 NC Not connected -
26 DA0
27 DA2
CN307 PWA-F-LGC (CN307) <-> EMP-U-SNR, CST-U-TRY-SNR, CST- 28 IDECS
29 DD1
U-FEED-CLT, NEMP-U-SNR, TRY-MOT, TR-L-CLT,
30 DD2
EMP-L-SNR, CST-L-TRY-SNR, CST-L-FEED-CLT,
31 DD4
NEMP-L-SNR, CST-U-SW, CST-L-SW 32 DD5
33 DD7
Pin No Symbol Name Active
34 DD8
A1 SG Signal ground -
35 DD10
A2 CUEMP-1 Upper drawer empty sensor detection signal -
36 DD11
A3 +5.1VB +5.1 V -
37 DD13
A4 SG Signal ground -
38 DD14
A5 CUTOP-1 Upper drawer tray-up sensor detection signal -
39 DD15
A6 +5.1VB +5.1 V -
40 /DIOR
A7 CURGC-0A Upper drawer feed clutch drive signal -
41 /DIOW
A8 +24VD1 +24 V -
42 /DMACK
A9 SG Signal ground -
43 /DLDCS0
A10 CUFLS-1 Upper drawer paper stock sensor detection signal -
44 /RESET
A11 +5.1VB +5.1 V -
45 DMARQ
A12 CLTRM-0A Tray-up motor drive signal -
46 NC
A13 CLTRM-1A Tray-up motor drive signal -
47 FXWP
A14 2NDCL-0A Lower transport clutch drive signal -
48 SG
A15 +24VD1 +24 V -
49 SG
B1 SG Signal ground -
50 NC
B2 CLEMP-1 Lower drawer empty sensor detection signal -
B3 +5.1VB +5.1 V -
B4 SG Signal ground - CN102 PWA-F-SYS (CN102) <-> PWA-F-SLG (CN4)
B5 CLTOP-1 Lower drawer tray-up sensor detection signal -
Pin No Symbol
B6 +5.1VB +5.1 V -
1 SYSRST
B7 CLRGC-0 Lower drawer feed clutch drive signal -
2 SCTS
B8 +24VD1 +24 V -
3 STXD
B9 SG Signal ground -
4 SRXD
B10 CLFLS-1 Upper drawer paper stock sensor detection signal -
5 SRTS
B11 +5.1VB +5.1 V
6 SCNT
B12 SG Signal ground -
7 SG
B13 CUSW-0 Upper drawer detection signal -
8 SVDEN
B14 SG Signal ground -
9 SDCLK
B15 CLSW-0 Lower drawer detection signal -
10 SHDEN
11 SG
12 SG
13 SCD7
14 SCD6
15 SCD5
16 SCD4
17 SCD3
18 SCD2
19 SCD1
20 SCD0
CN112 PWA-F-SYS (CN112) <-> HDD (CN170) (STANDARD)
Pin No Symbol
1 /RESET Reset signal
Name Active
2 SG Signal ground
Developer AC bias high-voltage clock signal -
3 DD7 Data bus [7]
High-voltage power supply leakage detection signal L
4 DD8 Data bus [8]
Separation bias voltage output reference voltage Analog
5 DD6 Data bus [6]
Separation bias voltage ON/OFF signal -
6 DD9 Data bus [9]
Transfer guide bias voltage ON/OFF signal -
7 DD5 Data bus [5]
Transfer bias high-voltage output reference voltage Analog
8 DD10 Data bus [10]
Transfer bias high-voltage ON/OFF signal -
9 DD4 Data bus [4]
Developer AC bias high-voltage output reference
Analog 10 DD11 Data bus [11]
voltage
11 DD3 Data bus [3]
Developer AC bias high-voltage ON/OFF signal -
12 DD12 Data bus [12]
Developer DC bias high-voltage output reference
Analog 13 DD2 Data bus [2]
voltage
14 DD13 Data bus [13]
Main charger grid output reference voltage Analog
15 DD1 Data bus [1]
Main needle electrode charger voltage ON/OFF
16 DD14 Data bus [14]
-
signal
17 DD0 Data bus [0]
Signal ground -
18 DD15 Data bus [15]
+24 V
19 SG Signal ground
Fuser roller thermistor connection detection signal -
20 NC(KEY) Not connected
Fuser roller center thermistor + signal Analog
21 MDARQ DMA request signal
Fuser roller center thermistor - signal Analog
22 SG Signal ground
Fuser roller side thermistor + signal Analog
23 /DIOW I/O write signal
Fuser roller side thermistor - signal Analog
24 SG Signal ground
Fuser roller edge thermistor + signal Analog 25 /DIOR I/O read signal
Fuser roller edge thermistor - signal Analog 26 SG Signal ground
+5.1 V - 27 IORDY I/O ready signal
Signal ground - 28 SG Signal ground
Exit sensor detection signal - 29 /DMACK DMA acknowledge signal
+5.1 V - 30 SG Signal ground
Not connected - 31 INTRQ Interrupt request signal
Not connected -
NC(RESERV
32 Reserve signal
Not connected -
ED)
33 DA1 Device address [1]
34 /PDIAG Passed diagnostics
35 DA0 Device address [0]
Name Active
36 DA2 Device address [2]
PFP/LCF driver control latch signal (C) -
37 /CS0 Chip select-0
PFP/LCF driver control latch signal (B) -
38 /CS1 Chip select-1
PFP/LCF sensor detection port enable signal (C) -
39 /DASP Device active or slave present signal
PFP/LCF driver control signal -
40 SG Signal ground
PFP/LCF driver control signal -
PFP/LCF driver control signal -
PFP/LCF driver control signal - CN113 PWA-F-SYS (CN113) <-> HDD (CN171)
PFP/LCF driver control signal -
Pin No Symbol
PFP/LCF driver control signal -
1 +12V +12 V
PFP/LCF driver control signal -
2 SG Signal ground
PFP/LCF driver control signal -
3 SG Signal ground
Reset signal -
4 +5.1VA +5.1 V
+5.1 V -
Signal ground -
CN116 PWA-F-SYS (CN116) <->DIMM (0)
+24 V -
+24 V - Pin No Symbol
Power ground - 1 SG Signal ground
Power ground - 2 DQ0 Memory data bus [0]
Size data bus-0 - 3 DQ1 Memory data bus [1]
4 DQ2 Memory data bus [2]
Size data bus-1 -
5 DQ3 Memory data bus [3]
Size data bus-2 -
6 +3.3VA +3.3 V
Size data bus-3 -
7 DQ4 Memory data bus [4]
PFP/LCF sensor detection signal -
8 DQ5 Memory data bus [5]
PFP/LCF sensor detection signal -
9 DQ6 Memory data bus [6]
PFP/LCF sensor detection signal -
10 DQ7 Memory data bus [7]
PFP/LCF sensor detection signal -
11 DQ8 Memory data bus [8]
PFP/LCF sensor detection signal -
PFP/LCF sensor detection signal - 12 SG Signal ground
PFP/LCF sensor detection signal - 13 DQ9 Memory data bus [9]
PFP/LCF sensor detection signal - 14 DQ10 Memory data bus [10]
PFP/LCF sensor detection port enable signal (B) - 15 DQ11 Memory data bus [11]
LCF connection detection signal L 16 DQ12 Memory data bus [12]
17 DQ13 Memory data bus [13]
18 +3.3VA +3.3 V
19 DQ14 Memory data bus [14]
Name Active
20 DQ15 Memory data bus [15]
Polygonal motor reference clock signal -
21 NC Not connected
Polygonal motor PLL signal L: Normal
22 NC Not connected
L: ON
23 SG Signal ground
Polygonal motor ON/OFF signal
H: OFF 24 NC Not connected
Power ground - 25 NC Not connected
+24 V - 26 +3.3VA +3.3 V
27 /WE Data write enable signal
28 DQMB0 Output disable/write mask-0
29 DQMB1 Output disable/write mask-1
Name Active
30 /CS0 Chip select signal-0
Signal ground -
31 NC Not connected
+5.1 V -
32 SG Signal ground
+5.1 V -
33 A0 Memory address bus [0]
Signal ground -
34 A2 Memory address bus [1]
Laser power control signal (reference voltage) -
35 A4 Memory address bus [2]
Signal ground -
36 A6 Memory address bus [3]
Laser beam position detection signal (H-sync) -
37 A8 Memory address bus [4]
Signal ground -
38 A10 Memory address bus [10]
Laser image data (differential signal +) -
39 BA1 Bank select-1
Laser image data (differential signal -) -
40 +3.3VA +3.3 V
Signal ground -
41 +3.3VA +3.3 V
APC write signal -
42 CLK0 Clock-0 input
+5.1 V -
43 SG Signal ground
Laser shut down signal -
44 NC Not connected
Signal ground -
45 /CS2 Chip select signal-2
+5.1 V
46 DQMB2 Output disable/write mask-2
+5.1 V -
47 DQMB3 Output disable/write mask-3
Signal ground -
48 NC Not connected
49 +3.3VA +3.3 V
50 NC Not connected
Name Active
51 NC Not connected
ROM data bus [0] - 52 NC Not connected
ROM data bus [2] - 53 NC Not connected
ROM data bus [4] - 54 SG Signal ground
ROM data bus [6] - 55 DQ16 Memory data bus [16]
ROM data read signal - 56 DQ17 Memory data bus [17]
ROM address bus [0] - 57 DQ18 Memory data bus [18]
ROM address bus [2] - 58 DQ19 Memory data bus [19]
ROM address bus [4] - 59 +3.3VA +3.3 V
ROM address bus [6] - 60 DQ20 Memory data bus [20]
ROM address bus [8] - 61 NC Not connected
ROM address bus [10] - 62 NC Not connected
ROM address bus [12] - 63 CKE1 Clock enable signal
ROM address bus [14] - 64 SG Not connected
ROM address bus [16] - 65 DQ21 Memory data bus [21]
ROM address bus [18] - 66 DQ22 Memory data bus [22]
Signal ground - 67 DQ23 Memory data bus [23]
Signal ground - 68 SG Signal ground
ROM data bus [1] - 69 DQ24 Memory data bus [24]
ROM data bus [3] - 70 DQ25 Memory data bus [25]
ROM data bus [5] - 71 DQ26 Memory data bus [26]
ROM data bus [7] - 72 DQ27 Memory data bus [27]
Chip select signal L 73 +3.3VA +3.3 V
ROM address bus [1] - 74 DQ28 Memory data bus [28]
ROM address bus [3] - 75 DQ29 Memory data bus [29]
ROM address bus [5] - 76 DQ30 Memory data bus [30]
ROM address bus [7] - 77 DQ31 Memory data bus [31]
ROM address bus [9] - 78 SG Signal ground
ROM address bus [11] - 79 CLK2 Clock-2 input
ROM address bus [13] - 80 NC Not connected
ROM address bus [15] - 81 NC(WP) Not connected
ROM address bus [17] - 82 SDA PD serial data
Download board connection detection signal L 83 SCL PD serial clock
+5.1 V - 84 +3.3VA +3.3 V
External ROM loading status signal L 85 SG Signal ground
86 DQ32 Memory data bus [32]
87 DQ33 Memory data bus [33]
88 DQ34 Memory data bus [34]
Name Active
89 DQ35 Memory data bus [35]
Signal ground -
90 +3.3VA +3.3 V
+5.1 V -
91 DQ36 Memory data bus [36]
System address bus [0] -
92 DQ37 Memory data bus [37]
System address bus [2] -
93 DQ38 Memory data bus [38]
System address bus [4] -
94 DQ39 Memory data bus [39]
System address bus [6] -
95 DQ40 Memory data bus [40]
System data bus [0] -
96 SG Signal ground
System data bus [2] -
97 DQ41 Memory data bus [41]
System data bus [4] -
98 DQ42 Memory data bus [42]
System data bus [6] -
99 DQ43 Memory data bus [43]
Signal ground -
100 DQ44 Memory data bus [44]
Write signal -
101 DQ45 Memory data bus [45]
IPC chip select signal -
102 +3.3VA +3.3 V
+5.1 V -
103 DQ46 Memory data bus [46]
IPC board connection detection signal L
104 DQ47 Memory data bus [47]
Signal ground -
105 NC Not connected
+5.1 V -
106 NC Not connected
System address bus [1] -
107 SG Signal ground
System address bus [3] -
108 NC Not connected
System address bus [5] -
109 NC Not connected
System address bus [7] -
110 +3.3VA +3.3 V
System data bus [1] -
111 /CAS Column address strobe signal
System data bus [3] -
112 DQMB4 Output disable/write mask-4
System data bus [5] -
113 DQMB5 Output disable/write mask-5
System data bus [7] -
114 /CS1 Chip select signal-1
Signal ground -
115 /RAS Row address strobe signal
Output enable signal -
116 SG Signal ground
IPC reset signal -
117 A1 Memory address bus [1]
+5.1 V -
118 A3 Memory address bus [3]
Signal ground -
119 A5 Memory address bus [5]
120 A7 Memory address bus [7]
121 A9 Memory address bus [9]
122 BA0 Bank select-0
Name Active
123 A11 Memory address bus [11]
System data bus [0] -
124 +3.3VA +3.3 V
System data bus [2] -
System data bus [4] - 125 NC(CLK1) Clock-1 input
System data bus [6] - 126 A12 Memory address bus [12]
System data bus [8] - 127 SG Signal ground
System data bus [10] - 128 CEK Clock enable signal
System data bus [12] - 129 /CS3 Chip select signal-3
System data bus [14] - 130 DQMB6 Output disable/write mask-6
System address bus [21] - 131 DQMB7 Output disable/write mask-7
132 NC(A13) Memory address bus [13]
System address bus [19] -
133 +3.3VA +3.3 V
System address bus [17] -
134 NC Not connected
System address bus [15] -
135 NC Not connected
System address bus [13] -
136 NC Not connected
System address bus [11] -
137 NC Not connected
System address bus [9] -
138 SG Signal ground
System address bus [7] -
139 DQ48 Memory data bus [48]
System address bus [5] -
140 DQ49 Memory data bus [49]
System address bus [3] -
141 DQ50 Memory data bus [50]
System read signal -
142 DQ51 Memory data bus [51]
Chip select signal (7-A) -
143 +3.3VA +3.3 V
Chip select signal (7-B) -
144 DQ52 Memory data bus [52]
+3.3 V -
+3.3 V - 145 NC Not connected
Signal ground - 146 NC Not connected
Signal ground - 147 NC Not connected
System data bus [1] - 148 SG Signal ground
System data bus [3] - 149 DQ53 Memory data bus [53]
150 DQ54 Memory data bus [54]
System data bus [5] -
151 DQ55 Memory data bus [55]
System data bus [7] -
152 SG Signal ground
System data bus [9] -
153 DQ56 Memory data bus [56]
System data bus [11] -
154 DQ57 Memory data bus [57]
System data bus [13] -
155 DQ58 Memory data bus [58]
System data bus [15] -
156 DQ59 Memory data bus [59]
System address bus [20] -
157 +3.3VA +3.3 V
System address bus [18] -
158 DQ60 Memory data bus [60]
System address bus [16] -
159 DQ61 Memory data bus [61]
System address bus [14] -
160 DQ62 Memory data bus [62]
System address bus [12] -
161 DQ63 Memory data bus [63]
System address bus [10] -
162 SG Signal ground
System address bus [8] -
System address bus [6] - 163 NC(CLK3) Clock-3 input
System address bus [4] - 164 NC Not connected
System address bus [2] - 165 SA0 PD address [0]
External ROM loading status signal - 166 SA1 PD address [1]
System chip select signal-0 - 167 SA2 PD address [2]
+3.3 V - 168 +3.3VA +3.3 V
System control signal -
System write signal - CN117 PWA-F-SYS (CN117) <-> PWA-F-LGC (CN309)
Signal ground -
Pin No Symbol
Signal ground -
A1 +5.1VB +5.1 V
A2 CBSY-0 System command busy
A3 CMD-0 Command data
A4 SACK-0 System status acknowledge signal
Name Active
+5.1 V - A5 SERR-0 System status error signal
Address bus [1] - A6 SBSY-0 System status busy signal
+5.1 V - A7 STS-0 Status data
FAX data bus [0] - A8 CACK-0 System command acknowledge signal
+5.1 V - A9 CERR-0 System command error signal
FAX data bus [3] - A10 SG Signal ground
A11 SG Signal ground
+5.1 V -
A12 SG Signal ground
FAX data bus [6] -
A13 IRCLK-1 Clock signal input for image data transmission
+5.1 V -
A14 SG Signal ground
FAX data bus [9] -
A15 IHSYNC-0 Horizontal scanning synchronized signal
Signal ground -
A16 SG Signal ground
FAX data bus [12] -
A17 IVSYNC-0 Vertical scanning synchronized signal
Signal ground -
B1 MCNT LGC board connection detection signal
Signal ground -
B2 SYSRST-0 System reset signal
Signal ground -
B3 IDATX[0] IDA Transmitted data bus [0]
Signal ground -
B4 IDATX[1] IDA Transmitted data bus [1]
Signal ground -
B5 IDATX[2] IDA Transmitted data bus [2]
Signal ground -
+3.3 V - B6 IDATX[3] IDA Transmitted data bus [3]
Interrupt request signal - B7 IDATX[4] IDA Transmitted data bus [4]
+3.3 V - B8 IDATX[5] IDA Transmitted data bus [5]
+5.1 V - B9 IDATX[6] IDA Transmitted data bus [6]
-12 V - B10 IDATX[7] IDA Transmitted data bus [7]
Analog ground - B11 SG Signal ground
+12 V - B12 IDCLK-1 Clock signal output for image data transmission
B13 SG Signal ground
Address bus [0] -
B14 IHDEN-0 Data enable of the horizontal scanning direction
Address bus [2] -
B15 SG Signal ground
IDE chip select signal -
B16 IVDEN-0 Data enable of the vertical scanning direction
FAX data bus [1] -
B17 +3.3VB +3.3 V
FAX data bus [2] -
FAX data bus [4] -
FAX data bus [5] - CN118 PWA-F-SYS (CN118) <-> PWA-F-DSP (J427)
FAX data bus [7] -
Pin No Symbol
FAX data bus [8] -
1 XSCL-1A LCD data transmission clock
FAX data bus [10] -
2 LP-1A LCD data latch pulse
FAX data bus [11] -
3 WF-1A LCD frame signal
FAX data bus [13] -
4 YD-1A LCD scanning line start signal
FAX data bus [14] -
5 INVGND Signal ground
FAX data bus [15] -
6 BZON-0A Buzzer-ON signal
Data read signal -
7 CPPOW-1A Panel connection detection signal
Data write signal -
8 LDCLK-1A LED serial clock
DMA acknowledge signal -
9 LDDAT-1A LED serial data
Chip select signal -
10 LDLTH-1A LED data latch signal
Reset signal L
11 LDON1-0A LED drive selection signal-1
DMA request signal -
12 LDON0-0A LED drive selection signal-0
Not connected -
13 SG Signal ground
FAX wake-up signal -
14 +5.1VB +5.1 V
Signal ground -
15 +5.1VB +5.1 V
Signal ground -
16 +5.1VB +5.1 V
Not connected -
17 +5.1VB +5.1 V
18 CPRST-0A Reset signal
19 SG Signal ground
Name Active 20 RTS0-0A Key controller SIO Transmission request signal
System reset signal - 21 CTS0-0A Key controller SIO Transmission enabled signal
Transmission enabled - 22 SOUT(0) Key controller SIO transmitted serial data
Transmitted SLG data - 23 SIN(0) Key controller SIO received serial data
Received SLG data - 24 SG Signal ground
25 UD3-1A LCD display data-3
Transmission request signal -
26 UD2-1A LCD display data-2
SLG board connection detection signal -
27 UD1-1A LCD display data-1
Signal ground -
28 UD0-1A LCD display data-0
Vertical scanning synchronized signal -
29 SG Signal ground
Clock signal for scanning data transmission -
30 LCDEN-1A LCD enable signal
Horizontal scanning synchronized signal -
Signal ground -
Signal ground -
CN119 PWA-F-SYS (CN119) <-> USB DEVICE
Scanning data [7] -
Pin No Symbol
Scanning data [6] -
1 VBUS (+5.1 V)
Scanning data [5] -
2 D- USB serial data
Scanning data [4] -
3 D+ USB serial data
Scanning data [3] -
4 SG Signal ground
Scanning data [2] -
Scanning data [1] -
CN120 PWA-F-SYS (CN120) <-> USB HOST
Scanning data [0] -
Pin No Symbol
1 VBUS +5.1 V
2 D- USB serial data
3 D+ USB serial data
4 SG Signal ground
5 VBUS +5.1 V
6 D- USB serial data
7 D+ USB serial data
8 SG Signal ground
CN121 PWA-F-SYS (CN121) <-> PWA-F-NIC (J3)
Name Active Pin No Symbol Name
- 1 +3.3VA +3.3 V
- 2 +3.3VA +3.3 V
- 3 +3.3VA +3.3 V
- 4 NC (/CS2P) Not connected
- 5 D15 I/F data bus [15]
- 6 D14 I/F data bus [14]
- 7 D13 I/F data bus [13]
- 8 SG Signal ground
- 9 D12 I/F data bus [12]
- 10 D11 I/F data bus [11]
- 11 D10 I/F data bus [10]
- 12 SG Signal ground
- 13 D09 I/F data bus [9]
- 14 D08 I/F data bus [8]
- 15 /INTPR1 Interrupt PR1 signal
- 16 SG Signal ground
- 17 A03 I/F address bus [3]
- 18 A02 I/F address bus [2]
- 19 A01 I/F address bus [1]
- 20 NC (SRXD) Not connected
H 21 A00 I/F address bus [0]
- 22 D07 I/F data bus [7]
- 23 D06 I/F data bus [6]
- 24 A15 I/F address bus [15]
- 25 D05 I/F data bus [5]
- 26 A14 I/F address bus [14]
- 27 D04 I/F data bus [4]
- 28 A13 I/F address bus [13]
L 29 D03 I/F data bus [3]
- 30 A12 I/F address bus [12]
H 31 D02 I/F data bus [2]
32 A11 I/F address bus [11]
-
33 D01 I/F data bus [1]
- 34 A10 I/F address bus [10]
L 35 D00 I/F data bus [0]
- 36 A09 I/F address bus [9]
- 37 A04 I/F address bus [4]
38 A08 I/F address bus [8]
L
39 /RESET System reset signal
L
40 A07 I/F address bus [7]
L
41 /ACK Acknowledge signal
-
42 A06 I/F address bus [6]
43 /CSP1 Chip select signal
44 A05 I/F address bus [5]
Name Active
45 NC (OEO) Not connected
-
46 NC (STXD) Not connected
-
47 RW Read/write to NIC
-
48 SG Signal ground
-
49 A16 I/F address bus [16]
50 SG Signal ground
51 +3.3VA +3.3 V
52 SG Signal ground
Name Active
53 NC (DACK) Not connected
-
54 +3.3VA +3.3 V
-
55 /INTPR2 PR2 interrupt signal
-
56 SG Signal ground
-
57 BRDNIN NIC board connection detection signal
-
58 +3.3VA +3.3 V
-
59 +3.3VA +3.3 V
-
60 +3.3VA +3.3 V
-
-
- CN124 PWA-F-SYS (CN124) <-> PCI (CN150)/
-
SCRAMBLER BOARD (OPTION)
-
Pin No Symbol Name
-
1 +3.3VA +3.3 V
-
2 +3.3VA +3.3 V
-
3 +3.3VA +3.3 V
-
4 SG Signal ground
-
5 -12VA -12 V
-
6 -12VA -12 V
-
7 +5.1VA +5.1 V
-
8 +5.1VA +5.1 V
-
9 +3.3VA +3.3 V
-
10 OPBINT(2) Interrupt request-2
-
11 OPBINT(0) Interrupt request-0
-
12 SG Signal ground
-
13 PCICLK(5) PCI clock-5 (Not used)
-
14 SG Signal ground
-
15 PCICLK(3) PCI clock-3
-
16 SG Signal ground
-
17 REQ(1)# Data request signal-1
-
18 REQ(0)# Data request signal-0
-
19 +3.3VA +3.3 V
-
20 AD[31] PCI address/data bus [31]
-
21 AD[29] PCI address/data bus [29]
-
22 SG Signal ground
-
23 AD[27] PCI address/data bus [27]
-
24 AD[25] PCI address/data bus [25]
-
25 +3.3VA +3.3 V
-
26 C/BE(3]# Command and byte enable-3
-
27 AD[23] PCI address/data bus [23]
-
28 SG Signal ground
-
29 AD[21] PCI address/data bus [21]
-
30 AD[19] PCI address/data bus [19]
-
31 +3.3VA +3.3 V
-
32 AD[17] PCI address/data bus [17]
-
33 C/BE(2)# Command and byte enable-2
-
34 SG Signal ground
-
35 IRDY# Initiator ready
-
36 +3.3VA +3.3 V
-
37 DEVSEL# Device select
-
38 SG Signal ground
-
39 LOCK# Lock
-
40 PERR# Data parity Error
-
41 +3.3VA +3.3 V
-
42 SERR# System Error
-
43 +3.3VA +3.3 V
-
44 C/BE(1)# Command and byte enable-1
-
45 AD[14] PCI address/data bus [14]
-
46 SG Signal ground
-
47 AD[12] PCI address/data bus [12]
-
48 AD[10] PCI address/data bus [10]
-
49 M66EN PCI bus 66 MHz clock enable signal
-
50 SG Signal ground
-
51 AD[8] PCI address/data bus [8]
-
52 AD[7] PCI address/data bus [7]
-
53 +3.3VA +3.3 V
-
54 AD[5] PCI address/data bus [5]
-
55 AD[3] PCI address/data bus [3]
-
56 SG Signal ground
-
57 AD[1] PCI address/data bus [1]
-
58 +3.3VA +3.3 V
-
59 +5.1VA +5.1 V
-
60 SG Signal ground
-
61 +3.3VA +3.3 V
-
62 +3.3VA +3.3 V
-
63 +3.3VA +3.3 V
-
64 SG Signal ground
-
65 +12VA +12 V
-
66 +12VA +12 V
-
67 +5.1VA +5.1 V
-
68 +5.1VA +5.1 V
-
69 +3.3VA +3.3 V
-
70 OPBINT(1) Interrupt request-1
-
71 +3.3VA +3.3 V
-
72 PCIRST# PCI reset signal
-
73 +3.3VA +3.3 V
-
74 PCICLK(4) PCI clock-4
-
75 +3.3VA +3.3 V
-
76 GNT(1)# Grant-1
-
77 GNT(0)# Grant-0
-
78 SG Signal ground
-
79 PME# Power Management Event
-
80 AD[30] PCI address/data bus [30]
-
81 +3.3VA +3.3 V
-
82 AD[28] PCI address/data bus [28]
-
83 AD[26] PCI address/data bus [26]
-
84 SG Signal ground
-
85 AD[24] PCI address/data bus [24]
-
86 +3.3VA +3.3 V
-
87 +3.3VA +3.3 V
-
88 AD[22] PCI address/data bus [22]
-
89 AD[20] PCI address/data bus [20]
-
90 SG Ground
-
91 AD[18] PCI address/data bus [18]
-
92 AD[16] PCI address/data bus [16]
-
93 +3.3VA +3.3 V
-
94 FRAME# Cycle frame
-
95 SG Signal ground
-
96 TRDY# Target ready
-
97 SG Signal ground
-
98 STOP# Stop
-
99 +3.3VA +3.3 V
-
100 +3.3VA +3.3 V
-
101 SG Signal ground
-
102 SG Signal ground
-
103 PAR Parity
-
104 AD[15] PCI address/data bus [15]
-
105 +3.3VA +3.3 V
-
106 AD[13] PCI address/data bus [13]
-
107 AD[11] PCI address/data bus [11]
-
108 SG Signal ground
-
109 AD[9] PCI address/data bus [9]
-
110 SG Signal ground
-
111 C/BE(0)# Command and byte enable-0
-
112 +3.3VA +3.3 V
-
113 AD[6] PCI address/data bus [6]
-
114 AD[4] PCI address/data bus [4]
-
115 SG Signal ground
-
116 AD[2] PCI address/data bus [2]
-
117 AD[0] PCI address/data bus [0]
-
118 +3.3VA +3.3 V
-
119 +5.1VA +5.1 V
-
120 +5.1VA +5.1 V
-
-
- CN126 PWA-F-SYS (CN126) <-> COIN CONTROLLER (OPTION)/
-
COPY KEY CARD (OPTION)
-
Pin No Symbol Name
-
1 L/S Paper size signal
-
2 FULL-C Full-color mode signal
-
3 MONO-C Mono-color mode signal
-
4 B/W Black and white mode signal
-
5 +5.1VA +5.1 V
-
6 SG Signal ground
-
7 NC Not connected
-
-
CN705 PS-ACC (CN705) <-> PWA-F-SYS (CN122)
-
- Pin No Symbol Name
- 1 PWR-EN Power supply enable signal
- 2 PWR-DN AC main power down signal
- 3 -12VB -12 V
-
4 SG Signal ground
-
5 +12VB +12 V
-
6 SG Signal ground
-
7 +12VA +12 V
-
8 SG Signal ground
-
9 -12VA -12 V
-
10 SG Signal ground
-
11 SG Signal ground
-
12 SG Signal ground
-
13 +3.3VA +3.3 V
-
14 +3.3VA +3.3 V
- 15 +3.3VA +3.3 V
- 16 +3.3VA +3.3 V
- 17 SG Signal ground
- 18 SG Signal ground
- 19 +3.3VB +3.3 V
20 +3.3VB +3.3 V
21 SG Signal ground
22 SG Signal ground
23 SG Signal ground
Name Active
24 +5.1VA +5.1 V
-
25 +5.1VB +5.1 V
-
26 +5.1VA +5.1 V
-
-
CN706 PS-ACC (CN706) <-> PWA-F-LGC (CN311),
-
-
PWA-F-FUS (CN431)
-
Pin No Symbol Name
-
1 SG Signal ground
-
2 +5.1VD +5.1 V
-
3 PG Power ground
-
4 PG Power ground
-
5 +24VD2 +24 V
-
6 +24VD2 +24 V
-
7 PG Power ground
-
8 PG Power ground
-
9 PG Power ground
-
10 PG Power ground
-
11 +24VD1 +24 V
L
12 +24VD1 +24 V
-
13 +24VD1 +24 V
-
14 +24VD1 +24 V
-
15 NC Not connected
-
16 NC Not connected
-
17 NC Not connected
-
18 HTR2ON-1A Side heater ON/OFF signal of fuser roller
-
19 HTR1ON-1A Center heater ON/OFF signal of fuser roller
-
20 PSPDWN-1 AC main power down signal
-
21 SG Signal ground
-
22 +12VB +12 V
-
23 SG Signal ground
-
24 SG Signal ground
-
25 SG Signal ground (to FUS board)
-
26 +5.1VB +5.1 V (to FUS board)
-
27 +5.1VB +5.1 V
28 +5.1VB +5.1 V
29 SG Signal ground
30 +3.3VB +3.3 V
Name Active
-
H
CN707 PS-ACC (CN707) <-> PWA-FAX (CN702) (OPTION)/
H
FINISHER (J 599) (OPTION)/PWA-F-ADU (CN212) (OPTION)/
H
- MAIN MOTOR
L
Pin No Symbol Name
H
1 PG Signal ground
-
2 +24VB +24 V (to FAX board)
-
3 SG Signal ground
L
4 +5.1VB +5.1 V (to FINISHER)
L
5 NC Not connected
L
6 NC Not connected
-
7 PG Signal ground
-
8 +24VD5 +24 V (to FINISHER)
-
9 PG Power ground
-
10 PG Power ground
- 11 +24VD2 +24 V (to ADU)
L
12 +24VD2 +24 V (to ADU)
-
13 PG Power ground
-
14 PG Power ground
-
15 +24VD1 +24 V (to main motor)
-
16 +24VD1 +24 V (to main motor)
-
-
CN708 PS-ACC (CN708) <-> PWA-F-SLG (CN6)/
-
- RADF (CN1) (OPTION)
-
Pin No Symbol Name
-
1 SG Signal ground
-
2 SG Signal ground
H
3 +5.1VB +5.1 V
4 +5.1VB +5.1 V
5 +5.1VB +5.1 V (to RADF)
6 +5.1VB +5.1 V (to RADF)
Name Active
7 SG Signal ground
-
8 SG Signal ground
-
9 +3.3VB +3.3 V
-
10 +3.3VB +3.3 V
-
11 SG Signal ground
12 SG Signal ground
13 +12VB +12 V
Name Active 14 SG Signal ground
-
15 NC Not connected
- 16 NC Not connected
- 17 SG Signal ground
- 18 SG Signal ground
- 19 +24VD4 +24 V
- 20 +24VD4 +24 V
- 21 PG Power ground
- 22 PG Power ground
23 +24VD3 +24 V (to RADF)
24 +24VD3 +24 V (to RADF)
05/11
CN1 PWA-F-SLG (CN1) <-> PWA-F-CCD (CN14)
Active Pin No Symbol Name Active
- 1 +5.1VB +5.1 V -
- 2 +5.1VB +5.1 V -
- 3 SG Signal ground -
- 4 SG Signal ground -
- 5 CCDRS CCD RS signal -
- 6 SG Signal ground -
- 7 CCDCP CCD CP signal -
- 8 SG Signal ground -
- 9 CCDSH CCD SH signal -
- 10 SG Signal ground -
- 11 CCDCK2B CCD shift clock-2B -
- 12 SG Signal ground -
- 13 CCDCK2A CCD shift clock-2A -
- 14 SG Signal ground -
L 15 CCDCK1A CCD shift clock-1A -
- 16 SG Signal ground -
- 17 CCD-EVEN CCD even data -
- 18 SG Signal ground -
- 19 CCD-ODD CCD odd data -
- 20 SG Signal ground -
- 21 AG Analog ground -
- 22 AG Analog ground -
- 23 AG Analog ground -
- 24 +12VB +12 V -
- 25 +12VB +12 V -
- 26 +12VB +12 V -
-
-
CN2 PWA-F-SLG (CN2) <-> PLTN-SNR, HOME-SNR
-
Pin No Symbol Name Active
-
1 SG Signal ground -
-
2 PLTN-1A Platen sensor detection signal -
-
3 +5V +5.1 V -
-
4 SG Signal ground -
-
5 HOME-1A Carriage home position sensor detection signal -
-
6 +5V +5.1 V -
-
-
CN7 PWA-F-SLG (CN7) <-> RADF (CN2) (OPTION)
-
- Pin No Symbol Name Active
-
1 ACK RADF acknowledge signal -
-
2 SCN-STR VARID signal from RADF -
-
3 RXD Received serial data -
-
4 SG Signal ground -
-
5 TXD RADF transmitted serial data -
-
6 SG Signal ground -
-
7 DF-ACK Acknowledge signal from RADF -
-
8 DF-RRQ Request signal from RADF -
-
9 REQ RADF request signal -
-
10 CNT RADF connection detection signal -
-
-
CN9 PWA-F-SLG (CN9) <-> INV-EXP (CN1)
-
Pin No Symbol Name Active
-
1 PG Power ground -
-
2 PG Power ground -
-
3 LMPON-A Exposure lamp ON signal H
-
4 +24VD4 +24 V -
-
5 +24VD4 +24 V -
-
-
- CN10 PWA-F-SLG (CN10) <-> SLG-FAN-MOT,
APS1 (A4 SERIES ONLY), APS2, APS3, APS4, APS5
Pin No Symbol Name Active
1 NC Not connected -
2 NC Not connected -
Active
3 NC Not connected -
-
4 +5VAPS +5 V -
-
5 APSR Automatic original detection sensor signal -
-
6 SG Signal ground -
-
7 +5VAPS +5 V -
-
8 APSC Automatic original detection sensor signal -
-
9 SG Signal ground -
-
10 +5VAPS +5 V -
-
11 APS3 Automatic original detection sensor signal -
-
12 SG Signal ground -
-
13 +5VAPS +5 V -
-
14 APS2 Automatic original detection sensor signal -
-
15 SG Signal ground -
-
16 +5VAPS +5 V -
-
17 APS1 Automatic original detection sensor signal -
-
18 SG Signal ground -
-
-
- CN19 PWA-F-SLG (CN19) <-> SCAN-MOT
-
Pin No Symbol Name Active
-
1 SCNM-BB Scan motor drive signal-B -
-
2 +24VD4 +24 V -
-
3 SCNM-B Scan motor drive signal-B -
-
4 SCNM-AB Scan motor drive signal-A -
-
5 +24VD4 +24 V -
-
6 SCNM-A Scan motor drive signal-A -
-
-
CN22 PWA-F-SLG (CN22) <-> DOWNLOAD JIG (SLG)
-
Pin No Symbol Name Active
-
1 MDT[0] ROM data bus [0] -
-
2 MDT[2] ROM data bus [2] -
-
3 MDT[4] ROM data bus [4] -
-
4 MDT[6] ROM data bus [6] -
-
5 MRD ROM data read signal -
-
L 6 PNLDT[0] D/L address bus [0] -
- 7 PNLDT[1] D/L address bus [2] -
L 8 MAD[4] ROM address bus [4] -
- 9 MAD[6] ROM address bus [6] -
L 10 MAD[8] ROM address bus [8] -
L 11 MAD[10] ROM address bus [10] -
- 12 MAD[12] ROM address bus [12] -
L 13 MAD[14] ROM address bus [14] -
- 14 MAD[16] ROM address bus [16] -
- 15 MAD[18] ROM address bus [18] -
- 16 SG Signal ground -
- 17 SG Signal ground -
18 MDT[1] ROM data bus [1] -
-
19 MDT[3] ROM data bus [3] -
-
20 MDT[5] ROM data bus [5] -
-
21 MDT[7] ROM data bus [7] -
-
22 PNL_CS Chip select signal -
-
23 PNLDT1 D/L address bus [1] -
-
24 PNLDT3 D/L address bus [3] -
-
25 MAD[5] ROM address bus [5] -
-
- 26 MAD[7] ROM address bus [7] -
- 27 MAD[9] ROM address bus [9] -
- 28 MAD[11] ROM address bus [11] -
- 29 MAD[13] ROM address bus [13] -
- 30 MAD[15] ROM address bus [15] -
- 31 MAD[17] ROM address bus [17] -
- 32 ROMDT ROM connection detection signal -
- 33 +5.1VB +5.1 V -
- 34 LED LED drive signal -
-
- CN2 INV-EXP (CN2) <-> LP-EXPO
-
Pin No Symbol Name Active
-
1 - Exposure lamp high-voltage output -
-
2 NC Not connected -
-
3 NC Not connected -
-
4 - Exposure lamp high-voltage output -
-
-
J422 PWA-F-DSP (J422) <-> LCD PANEL
-
- Pin No Symbol Name Active
- 1 YD Y-axis touch position detection terminal-D -
- 2 KL X-axis touch position detection terminal-L -
- 3 XR X-axis touch position detection terminal-R -
- 4 YU Y-axis touch position detection terminal-U -
-
-
J423 PWA-F-DSP (J423) <-> LCD BACK LIGHT
-
Pin No Symbol Name Active
-
1 CCFL+ High-voltage terminal -
-
2 NC Not connected -
-
3 CCFL- High-voltage terminal -
-
-
J424 PWA-F-DSP (J424) <-> LCD PANEL
-
- Pin No Symbol Name Active
-
1 FRAME LCD scanning line start signal -
-
2 LAOD LCD data latch pulse -
-
3 CP LCD data transmission clock -
-
4 SG Signal ground -
-
5 +5.1VA +5.1 V -
L
6 SG Signal ground -
-
7 VEE Ground -
L
8 D.OFF LCD enable signal -
-
9 D0 LCD display data-0 -
L
10 D1 LCD display data-1 -
-
11 D2 LCD display data-2 -
-
12 D3 LCD display data-3 -
-
-
J425 PWA-F-DSP (J425) <-> PWA-F-KEY (J428)
-
Pin No Symbol Name Active
-
1 LDFC-1 LED driver output-1 L
-
2 LDFC-2 LED driver output-2 L
-
3 LDFC-4 LED driver output-4 L
-
4 LDFC-5 LED driver output-5 L
-
5 LDFC-6 LED driver output-6 L
-
6 LDFC-7 LED driver output-7 L
-
7 LDFC-8 LED driver output-8 L
-
8 LDFC-9 LED driver output-9 L
-
9 LDFC-10 LED driver output-10 L
-
10 LDFC-11 LED driver output-11 L
-
11 LDFC-12 LED driver output-12 L
-
12 LDFC-13 LED driver output-13 L
-
13 LDFC-15 LED driver output-15 L
-
- 14 LDON0 LED common driver signal-0 H
- 15 LDON1 LED common driver signal-1 H
- 16 SG Signal ground -
J426 PWA-F-DSP (J426) <-> PWA-F-KEY (J429)
Pin No Symbol Name Active
1 SCN15 Button scanning signal-5 -
Active
2 SCN14 Button scanning signal-4 -
-
3 SCN13 Button scanning signal-3 -
-
4 SCN12 Button scanning signal-2 -
-
5 SCN11 Button scanning signal-1 -
-
6 RET0 Button scanning return signal-0 -
-
7 RET1 Button scanning return signal-1 -
-
8 RET2 Button scanning return signal-2 -
-
9 RET3 Button scanning return signal-3 -
10 RET8 Button scanning return signal-8 -
11 RET9 Button scanning return signal-9 -
Active
L
J2 PWA-F-NIC (J2) <-> LAN (10BASE-T/100BASE-TX)
L
Pin No Symbol Name Active
-
1 (TD+)FA1 Transmitted data + -
-
2 (TD-)FA2 Transmitted data - -
-
3 (RD+)FA3 Received data + -
-
4 FA45 Not used -
-
5 FA45 Not used -
-
6 (RD-)FA6 Received data - -
-
7 FA78 Not used -
-
8 FA78 Not used -
-
9 NC(MTG) Not connected -
-
10 NC(MTG) Not connected -
-
11 SH Shield -
-
12 SH Shield -
-
13 SH Shield -
-
14 SH Shield -
-
-
CN206 PWA-F-LRL (CN206) <-> PER-F-LDR (C201)
-
- Pin No Symbol Name Active
- 1 SG Signal ground -
-
2 +5.1VD + 5.1 V -
- 3 +5.1VD + 5.1 V -
- 4 SG Signal ground -
- 5 WRLVL-1 Laser level control signal (reference voltage) -
- 6 SG Signal ground -
7 NC Not used -
8 SG Signal ground -
9 PIDT-1 Laser image data (differential signal +) -
10 PIDT-0 Laser image data (differential signal -) -
Active 11 SG Signal ground -
- 12 WRAPC-0 APC write signal -
- 13 NC Not used -
- 14 SHDWM-1 Laser shut down signal -
- 15 SG Signal ground -
- 16 +5.1VD + 5.1 V -
- 17 +5.1VD + 5.1 V -
- 18 SG Signal ground -
-
L
CN207 PWA-F-LRL (CN207) <-> PWA-F-SNS (CN202)
L
Pin No Symbol Name Active
-
1 +5.1VD + 5.1 V -
-
2 SG Signal ground -
-
3 BDIN-1 Laser beam position detection signal (H-sync) -
-
-
CN721 PS-HVT (OUT1) <-> HVT-MAIN
-
- Pin No Symbol Name Active
-
1 - High-voltage to main needle electrode charger -
-
L
CN722 PS-HVT (OUT2) <-> HVT-GRID
-
Pin No Symbol Name Active
-
1 - High-voltage to main charger grid -
-
-
-
CN723 PS-HVT (OUT3) <-> HVT-DEV
-
Pin No Symbol Name Active
-
1 - High-voltage to developer charger bias -
-
-
CN724 PS-HVT (OUT4) <-> HVT-TR
-
Pin No Symbol Name Active
1 - High-voltage to transfer charger bias -
CN725 PS-HVT (OUT5) <-> HVT-SEP
Pin No Symbol Name Active
Active
1 - High-voltage to separation charger bias -
-
-
CN726 PS-HVT (OUT6) <-> HVT-GB/RGT-ROL
-
Pin No Symbol Name Active
-
High-voltage to transfer guide bias and registra-
-
1 - -
- tion roller bias
-
-
CN213 PWA-F-ADU (CN213) <-> ADU-TRL-SNR
-
Pin No Symbol Name Active
-
1 SG Signal ground -
-
2 ADUFL ADU exit sensor detection signal -
-
3 +5.1VB + 5.1 V -
-
-
CN214 PWA-F-ADU (CN214) <-> ADU-TRU-SNR
-
- Pin No Symbol Name Active
1 SG Signal ground -
2 ADUFU ADU entrance sensor detection signal -
3 +5.1VB + 5.1 V -
Active
CN215 PWA-F-ADU (CN215) <-> ADU-MOT
-
Pin No Symbol Name Active
-
1 +24VD2 +24 V -
-
2 FDMA ADU motor drive signal-A -
-
3 FDMB ADU motor drive signal-B -
-
4 FDMC ADU motor drive signal-C -
-
5 FDMD ADU motor drive signal-D -
-
6 +24VD2 +24 V -
-
-
-
CN217 PWA-F-ADU (CN217) <-> ADU-SET-SW
-
Pin No Symbol Name Active
-
1 SG Signal ground -
-
2 COVSW ADU opening/closing detection signal -
-
-
-
-
-
-
-
-
-
-
-
CN501 FAX (CN501) <-> NCU (1) (OPTION)
Pin No Symbol Name Active
1 TXOUT Transmitted FAX data -
2 RXIN Received FAX data -
3 CML CML relay drive signal -
4 LD Dial pulse drive signal -
5 EXTRG RG relay drive signal -
6 ATT3DB -3 db ATT exchange signal -
7 RLADJ1 MODEM select signal -
8 RLADJ2 MODEM select signal -
9 RGCLK Ring clock -
10 AG Analog ground -
11 -12VB -12 V -
12 AG Analog ground -
13 +12VB +12 V -
14 +24VB +24 V -
15 16Hz Ring clock -
16 AG Analog ground -
17 CI Ring signal detection L
18 ANSDET FAX data answer detection L
19 REVA Line 1 External telephone hook detection signal L
20 REVB Line 1 External telephone hook detection signal L
21 INTHOOK Internal telephone hook signal -
22 EXTHOOK External telephone hook signal -
23 +5.1VB +5.1 V -
24 AG Analog ground -
25 +5.1VA +5.1 V -
26 -12VB -12 V -
27 AG Analog ground -
28 +12VB +12 V -
29 +24VB +24 V -
30 PG Power ground -
CN502 FAX (CN502) <-> NCU (2) (OPTION)
Pin No Symbol Name Active
1 TXB Transmitted FAX data -
2 RXIN Received FAX data -
3 CML CML relay drive signal -
4 LD Dial pulse drive signal -
5 ER/HK Not used -
6 ATT3DB -3 db ATT exchange signal -
7 RLADJ1 Modem select signal -
8 RLADJ2 Modem select signal -
9 RGCLK Not used
10 AG Signal ground -
11 -12VB -12 V -
12 AG Analog ground -
13 +12VB +12 V -
14 NC Not connected -
15 16Hz Not used -
16 AG Analog ground -
17 CI Ring signal detect L
18 ANSDET FAX data answer detection L
19 REVA Line 2 External telephone hook detection signal -
20 REVB Line 2 External telephone hook detection signal -
21 NC Not connected -
22 NC Not connected -
23 +5.1VA +5.1 V -
24 AG Analog ground -
25 +5.1VA +5.1 V -
26 -12VB -12 V -
27 AG Analog ground -
28 +12VB +12 V -
29 NC Not connected -
30 NC Not connected -
CN503 FAX (CN503) <-> SPEAKER (OPTION)
Pin No Symbol Name -
1 SP+ Speaker output (+) -
2 SP- Speaker output (-) -
CN600 FAX (CN600) <-> MDM (CN401) (OPTION)
Pin No Symbol Name Active
1 TXOUT2 Transmitted data -
2 +5.1VA +5.1 V -
3 +12VB +12 V -
4 +3.3VB +3.3 V -
5 MOD2DMA-1 Modem 2 DMA signal -
6 SG Signal ground -
7 MEM2CS-0 SRAM chip select signal -
8 +5.1VB +5.1 V -
9 MEMRD2-0 SRAM data read signal -
10 CLKOE-1 Clock out enable signal -
11 TXEN2-1 TX enable signal -
12 +5.1VB +5.1 V -
13 A[16] MDM address bus [16] -
14 A[14] MDM address bus [14] -
15 A[12] MDM address bus [12] -
16 A[10] MDM address bus [10] -
17 A[8] MDM address bus [8] -
18 A[6] MDM address bus [6] -
19 A[4] MDM address bus [4] -
20 A[2] MDM address bus [2] -
21 A[0] MDM address bus [0] -
22 +5.1VB +5.1 V -
23 CEP1RST-0 CEP1 reset signal -
24 5.1VB +5.1 V -
25 SG Signal ground -
26 CEPCLK System clock signal -
27 SG Signal ground -
28 D[0] MDM data bus [0] -
29 D[2] MDM data bus [2] -
30 D[4] MDM data bus [4] -
31 D[6] MDM data bus [6] -
32 D[8] MDM data bus [8] -
33 D[10] MDM data bus [10] -
34 D[12] MDM data bus [12] -
35 D[14] MDM data bus [14] -
36 SG Signal ground -
37 MOD2DET-0 Modem 2 detection signal -
38 SG Signal ground -
39 DREQC2-1 Data request signal -
40 DACKC2-0 Data acknowledge signal -
41 RXIN2 Received data -
42 AG Analog ground -
43 -12VB -12 V -
44 AG Analog ground -
45 MOD2INT-1 Modem 2 interrupt signal -
46 MOD2CS-0 Modem 2 chip select signal -
47 MOD2RST-0 Modem 2 reset signal -
48 SG Signal ground -
49 RXEN2-1 RX enable signal -
50 MEMWRH2-0 SRAM high byte write signal -
51 MEMWRL2-0 SRAM low byte write signal -
52 A[18] MDM address bus [18] -
53 A[17] MDM address bus [17] -
54 A[15] MDM address bus [15] -
55 A[13] MDM address bus [13] -
56 A[11] MDM address bus [11] -
57 A[9] MDM address bus [9] -
58 A[7] MDM address bus [7] -
59 A[5] MDM address bus [5] -
60 A[3] MDM address bus [3] -
61 A[1] MDM address bus [1] -
62 CPURST-0 CPU reset signal -
63 CEP2INT-1 CEP2 interrupt signal -
64 5.1VB +5.1 V -
65 5.1VB +5.1 V -
66 IORD2-0 MDM data read signal -
67 IOWR2-0 MDM data write signal -
68 D[1] MDM data bus [1] -
69 D[3] MDM data bus [3] -
70 D[5] MDM data bus [5] -
71 D[7] MDM data bus [7] -
72 D[9] MDM data bus [9] -
73 D[11] MDM data bus [11] -
74 D[13] MDM data bus [13] -
75 D[15] MDM data bus [15] -
76 5.1VB +5.1 V -
77 5.1VB +5.1 V -
78 CEP2CS-0 CEP2 chip select signal -
79 DREQD2-1 Data request signal -
80 DACKD2-0 Data acknowledge signal
CN602 FAX (CN602) <-> DOWNLOAD JIG (FAX) (OPTION)
Pin No Symbol Name Active
1 D[0] ROM data bus [0] -
2 D[2] ROM data bus [2] -
3 D[4] ROM data bus [4] -
4 D[6] ROM data bus [6] -
5 RD-0 ROM data read signal -
6 A[0] ROM address bus [0] -
7 A[2] ROM address bus [2] -
8 A[4] ROM address bus [4] -
9 A[6] ROM address bus [6] -
10 A[8] ROM address bus [8] -
11 A[10] ROM address bus [10] -
12 A[12] ROM address bus [12] -
13 A[14] ROM address bus [14] -
14 A[16] ROM address bus [16] -
15 A[18] ROM address bus [18] -
16 SG Signal ground -
17 SG Signal ground -
18 D[1] ROM data bus [1] -
19 D[3] ROM data bus [3] -
20 D[5] ROM data bus [5] -
21 D[7] ROM data bus [7] -
22 BOOTCS-0 Chip select signal -
23 A[1] ROM address bus [1] -
24 A[3] ROM address bus [3] -
25 A[5] ROM address bus [5] -
26 A[7] ROM address bus [7] -
27 A[9] ROM address bus [9] -
28 A[11] ROM address bus [11] -
29 A[13] ROM address bus [13] -
30 A[15] ROM address bus [15] -
31 A[17] ROM address bus [17] -
32 ROMDET0-0 Download board connection detection signal L
33 5.1VB +5.1 V -
34 LEDDL-0 External ROM loading status signal L
J600 IPC (J600) <-> FINISHER (J598) (OPTION)
Pin No Symbol Name Active
1 RXD Receiver serial data -
2 SG Signal ground -
3 TXD Transmitted serial data -
4 SG Signal ground -
5 NC Not connected -
6 NC Not connected -
7 NC Not connected -
8 NC Not connected -
9 F-CNT Finisher connection detection signal L
10 CNT-GND Ground -
(PCI BUS)PARALLEL BOARD <-> PC I/F (IEEE1284-C)
Pin No Symbol Name Active
1 BUSY Busy -
2 SELECT Select -
3 N ACK nAck -
4 NFAULT nFault -
5 PERROR PError -
6 DATA0 Data bus [0] -
7 DATA1 Data bus [1] -
8 DATA2 Data bus [2] -
9 DATA3 Data bus [3] -
10 DATA4 Data bus [4] -
11 DATA5 Data bus [5] -
12 DATA6 Data bus [6] -
13 DATA7 Data bus [7] -
14 NINIT nInit -
15 STB nStrobe -
16 NSEL IN nSelect In -
17 NATFD nAutoFd -
18 HLH Host Logic High -
19 SG Signal ground -
20 SG Signal ground -
21 SG Signal ground -
22 SG Signal ground -
23 SG Signal ground -
24 SG Signal ground -
25 SG Signal ground -
26 SG Signal ground -
27 SG Signal ground -
28 SG Signal ground -
29 SG Signal ground -
30 SG Signal ground -
31 SG Signal ground -
32 SG Signal ground -
33 SG Signal ground -
34 SG Signal ground -
35 SG Signal ground -
36 PLF Peripheral Logic High (Pull-up) H