Advertisement
• Remove the lower trim moulding and
panel by sliding it
downwards.
• Fit
new panel in
place
and slide it up as far as possible.
• Fit
the
trim
moulding back
BUILDING-IN
The
refrigerator is
intended for installation in
motorhome, and the description relates to
The
refrigerator must
not
be exposed to radiated heat from
hot objects
(e.g.
below a cooker without proper
ding).
Excessive heat
irradiation
impairs
increased energy consumption.
rator should
be
installed if possible
of
the
vehicle
-
normally orientated south and often
awning
which
would impair the dispersion
combustion gases from the
ventilation
It is not a good practice to install the refrigerator so that
vent
openings
are
covered by the vehicle's entrance door
when this
is
open.
Thi
s
would reduce
to
the cooling
unit
and
reduce refrigeration
The enclosure
The refrigerator
must be installed
dimensions of which are shown
The
bottom of the enclosure
so
that the refrigerator
can
be
must be sturdy enough
to
carry the wieght of the refrigera
tor.
Battens must
be
installed at the
sealing
strips,
as shown
in fig
Slide in
the refrigerator until it
recess.
There
must
be 10-20
refrigerator.
Four fasteners
are
fitted in plastic bushings in the
of
the
fridge, fig
.
7.
They
are
tor
in
the enclosure.
The side walls
of
the
enclosure and/or any
installed to hold
the
refrigerator must
seat
the screws
secure
ly,
also considering the forces due to
the movement
of
the
vehicle.
With the refrigerator in
place, drive
bushings
in
the lining of the refrigerator into the walls of the
enclosure (fig.7).
There
must not
clearance
between
refrigerator and enclosure on each side.
If
necessa
ry,
wooden strips or similar should be fitted.
Note: This
is the only approved means of
refrigerator to the
enclosure and
penetrating other parts
of
the insulation
refrigerator might
damage components
etc.
VENTILATION OF THE UNIT
At
high ambient temperatures
perform adequately
when properly ventilated.
The refrigeration unit
is ventilated via two openings
wall
of the
caravan
(see
fig.
lower
opening and warm air
one.
then
withdraw the
in
place.
a caravan or
this
application.
heat
shiel
performance and leads
For
this reason the refrige
not
at the
entrance
side
with
an
of
heat and
openings.
the
the
ventilation air
fl
ow
performance.
in an
enclosure,
the
in TECHNICAL DATA.
must be horizontal
and even
easily
pushed into
place.
It
enclosure
and fitted with
.
4.
is
flush
with
the
front
of
the
mm free space behind
the
side walls
used
for
securing
the refrigera
wooden braces
be dimensioned to
the
screws
through the
be
more
than
3mm of
securing
the
to the
vehicle.
Fasteners
(PU) foam
of the
like electric wiring
the refrigeration
unit will only
in
the
5).
Fresh
air
enters
through the
is
discharged
through the upper
Locate the lower opening immediately
recess, and the upper one
condenser (C) of
the refrigeration
fig.
6b but
preferably
Ventilation grilles Fig. 2
The
openings in
the
Electrolux
ventilation systems
Fitting
the
grilles, model A 1620, which
developed by
Electrolux for
6).
is a good
idea,
It
same figure),
at
the
easily removed which permits inspection and small
to
to
be carried out
without the necessity
refrigerator from the
If
there is
no
outer grille at floor level where leaking gas can
escape, a 40 mm
hole
floor
of
the recess to
gas.
Fit
the hole with wire mesh and an angled plate
from
stones, mud
etc
Removal of flue gases
The
ventilation passage at
the
outer wall of
the
sealed off
against
the living
excluded (winter camping) and no flue gases can penetrate
into
the
vehicle.
Thus
necessary
-
the gases
grille.
Note: With this mode
(without an integrated flue outlet), should be installed
upper
as well as at
T-piece
for
the
flue tube (when delivered) should not be
used in this
case.
The top
of
the
enclosure above
should be
covered with
in (B), to facilitate
the
In fig
.
6 the
letters have
A.
Frame R 1640 for the
B.
Aluminum
cladding
C.
Condenser
of cooling
D.
Vent
grill
A 1620
E.
Sealing profile (optional extra)
Width
486
mm
F.
Refrigerator
G.
Wooden
batten
H. Height of the
I.
Flue
tube
LP GAS
CON
CAUTION! CHECK THAT THE GAS SUPPLIED TO
THE REFRIGERATOR IS AT
PRESSURE. SEE THE REDUCING VALVE
LP GAS CONTAINER
The
refngerator
designed for
IS
Butane type
the
pressure
Butane and 37
mbar for
11
above the floor of the
as
high
as
possible above the
unit,
at
least
as shown in
as shown in fig. 6a.
caravan wall
must
be
fitted with the
.
were specially
this purpose (shown as
to install the frame R 1640
same
time. Then the grilles
for removing the
recess.
to the outside should be
drain
any unburnt
gas
to the outside
.
the
rear of the recess,
vehicle and
the refrigerator
space, and
so
cold
a
special
flue
outlet is
no longer
are
dispersed through the upper vent
of
installation the same type of grilles
the lower
vent open-ning
.
The
the flue tube
(I),
aluminum
sheet
metal
,
as indicated
heat dispersion.
the
following
meaning:
grilles
unit
,
Electrolux art. nr. 295 1147-10
rear wall
approx. 10
x 20
mm (see fig
enclosure
(see
TECHNICAL
NECTION
THE
CORRECT
ON
operation
on
LP
of
which must
be 28
mbar
Propane.
D
in
fig.
(A
in
the
can be
repairs
made in the
to
protect
between
(fig. 6)
,
is
draughts are
at
the
angled
fig
6,
.
4)
DATA)
THE
gas
of
for
Hide quick links:
Advertisement
