When Playing DTS-encoded CDs, excessive noise will be exhibited from the analog stereo outputs. The consumer should take proper precautions when the analog stereo outputs of the CD player is connected to an amplification system. To enjoy DTS Digital Surround playback, an external 5.1 channel DTS Digital Surround decoder system must be connected to the digital output (S/PDIF, ASE/EBU, or TosLink) of the CD player.
Introduction Before applying power Units are designed for operation as follows. U.S.A. and Canada ... AC 120 V only Australia ... AC 240 V only *AC voltage selection The AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped.
¶ MULTI EDIT: Several CDs can be edited and recorded on 1 tape. (Except for CD-206/ DPF-R6010) ¶ Auto space function. ¶ Easy operation functions allow systematic operation with other KENWOOD components connected through the system control connection. System control cord ... (1) Batteries (R6/AA) ...
System connections Caution: Do not plug in the power lead until all connections are completed. Make connections as shown below. When connecting the related system components, refer also to the instruction manuals of the related components. SL 16/XS8 switch CD-206/DPF-R6010 : LINE OUTPUT VARI ABLE AC110-220V...
2. Do not connect system control cords to any components other than those specified by KENWOOD. It may cause a malfunction and damage your equipment. 3. Be sure the system control plugs are inserted all the way in to the system control terminals.
Disc No. indicators The illustration of the common parts is of CD-206/DPF-R6010. Except for USA Canada CD-204/203 DPF-R4010/R3010 -ON –STANDBY MULTIPLE CD PLAYER DPF-R6010 POWER -ON –STANDBY COMPACT D.R.I.V.E. TEXT DIGITAL AUDIO About the STANDBY mode When the power cord of this unit is plugged into an AC outlet, a small amount of current is being supplied to the unit even when the ON/STANDBY switch is not depressed (–).
The keys with the same name as those on the remote control unit operate the same way as the remote control unit. 1 ON/STANDBY (POWER / ) switch Turns the unit ON/STANDBY. 2 P.MODE key 3 TEXT DISP. key (CD-206/DPF-R6010 only) Used to select the CD-TEXT information display.
3. Malfunction may occur if direct sunlight or the light of a high-frequency lighting fluorescent lamp enters the remote control light sensor. In such a case, change the system installation position to prevent the malfunction. (Except for CD-203/DPF-R3010) The keys with the same name as those on the main unit operate the same way as on the main unit.
ALL TEXT SEARCH (CD-206/DPF-R6010 only) For most CD-TEXT discs, it is convenient to read the complete disc information into the CD player before playing the disc. This allows text information such as TITLE SEARCH, TEXT DISPLAY, ALL INFO., and other messages to be displayed faster.
Normal play (TRACK mode) Use the following procedure to play a CD in the original order of tracks from track No. 1. Playing tracks in order from track No. 1 Check that the unit is in the normal play TRACK mode.
Playback from desired track Select the disc. DISC 1 DISC 2 Select the desired track No. Main unit ¢ Skipping tracks To skip backward Searching Backward search What is the “normal play TRACK mode”? The normal play TRACK mode refers to the state in which the PGM, EDIT and RANDOM mode displays are off. To set the unit to the TRACK mode: Press the P.MODE key when the ”PGM“...
Searching for tracks by title (TITLE SEARCH) In the case of a CD-TEXT disc, the tracks to be heard can be searched by title. Preparation ÷ Load a disc (CD-TEXT support) in the CD player. ÷ Check that the unit is in the normal play TRACK mode.
Displays (CD-206/DPF-R6010 only) Selecting the text information display (TEXT DISPLAY) In the case of a CD-TEXT disc, the displays shown below can be selected. DISPLAY REMOTE CONTROL UNIT RC-P0601 : A C ÷ When there is no text information to be displayed “– – – – –” is scrolled on the display.
Use the following procedure to program desired tracks in a desired order. (up to 32 tracks) Preparation ÷ Load a disc in the CD player. Press so that the “PGM” indicator lights. Do this operation in the stop mode. Program desired tracks.
To stop playback To check or change the programmed tracks Press the CHECK key. CD-206/DPF-R6010 CHECK REMOTE CONTROL UNIT RC-P0601 CD-204/203/DPF-R4010/R3010 CHECK Select the disc. DISC 1 DISC 2 Select the new track No. Main unit ¢ Set the entry. To add a track to the program Select the disc.
DPSS function (which works by searching the non-recorded spaces) can be performed reliably. Time display on CD player (TIME DISP.) Each press of the TIME DISP. (TIME DISPLAY) key changes the displayed contents.
Playback in a random order (Random playback) As tracks are selected at random, you can enjoy listening to for a long time. Preparation ÷ Load a disc in the CD player. ™ Check that the unit is in the normal play TRACK mode.
Repeated playback Preparation ÷ Load a disc in the CD player. ™ To repeat only the programmed tracks Press so that the “PGM” indicator lights. Select the disc. DISC 1 Go to step 3 within 8 seconds. Select the desired track number.
To repeat one of the discs (CD-204/203/DPF-R4010/R3010 only) Press so that the “PGM” indicator lights. Select the disc. DISC 1 DISC 2 Press the P.MODE key. Press the REPEAT key. Start playback. To repeat the entire disc This allows repeated playback of all the tracks on the disc loaded in the disc tray.
A and B. Normal EDIT: Edit from one disc. MULTI EDIT: Edit and record from several discs. Preparation ÷ Load a disc in the CD player. ÷ Check that the unit is in the normal play TRACK mode. Normal EDIT Light the “EDIT”...
Several CDs can be edited and recorded on 1 tape. Choose songs from each disc, and edit/record while con- firming the remaining time on files A and B, respectively. MULTI EDIT (Except for CD-206/DPF-R6010) Press so that the "MULTI EDIT " indicator light. Do this operation in the stop mode.
When recording the edited content onto a tape, it is recommended to use the synchro recording or CCRS recording function of KENWOOD cassette decks. ÷ Do not adjust the output level from this unit particularly during record- ing.
1. Some amplifiers cannot be used with a timer. Before using a amplifier, check it. Notes Notes 2. When operating the unit other than CD player using an audio timer, be sure to remove the disc from the CD player. This unit System control cord ÷...
Storage When a disc is not to be played for a long period of time, remove it from the CD player and store it in its case. Cleaning Do not use volatile solvents such as alcohol, paint thinner, gasoline, or benzine, etc.
Unplug the power cord from the power socket and plug the power cord into the socket again. ÷ Please be aware that resetting the CD player will erase all stored information and return it to the factory settings. Cause ÷...
Weight (Net) ... 5.0 kg (11.0 lb) 1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice. 2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).
CD-206/204/203/DPF-R6010/R4010/R3010 (En) For your records Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your dealer for information or service on this product.