Download  Print this page

Introduction; Before Applying Power; Safety Precautions - Kenwood DPF-J5010 Instruction Manual

Kenwood multiple compact disc player instruction manual.
Hide thumbs

Advertisement

Introduction

Before applying power

2
Units are designed for operation as follows.
U.S.A. and Canada .................................. AC 120 V only
Australia .................................................. AC 240 V only
*AC voltage selection
The AC voltage selector switch on the rear panel is set to the voltage
that prevails in the area to which the unit is shipped.
connecting the power cord to your AC outlet, make sure that the
setting position of this switch matches your line voltage. If not, it must
be set to your voltage in accordance with the following direction.
Note:
Our warranty does not cover damage caused by excessive line
voltage due to improper setting of the AC voltage selector switch.
For the United Kingdom
1. The mains plug contains a fuse. For replacement, use only a 13-Amp ASTA-approved (BS1362) fuse.
2. The fuse cover must be refitted when replacing the fuse in the moulded plug.
3. Do not cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach
a power point, then obtain an appropriate safety approved extension lead or adapter, or consult your dealer.
If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent
connection to the mains supply.
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:
Blue
: Neutral
Brown : Live
Do not connect those leads to the earth terminal of a three-pin plug.

Safety precautions

WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE
USER TO THE PRESENCE OF UNINSULATED "DANGEROUS VOLTAGE" WITHIN THE PRODUCT'S ENCLOSURE THAT MAY
BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE
OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING
THE APPLIANCE.
REQUIREMENT BY NEDERLAND GAZETTE
Batteries are supplied with this product. When
they empty, you should not throw away. In-
stead, hand them in as small chemical waste.
Caution : Read this section carefully to ensure safe operation.
Europe and U.K. ............................................... AC 230 V only
*Other countries ............. AC 110-120 / 220-240 V switchable
AC voltage selector switch
Before
Factory fitted moulded mains plug
Caution : Read this section carefully to ensure safe operation.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SER-
VICE PERSONNEL.
The marking is located on the rear panel and says that the component
uses laser beams that have been classified as Class 1. It means that
the unit is utilizing laser beams that are of a weaker class. There is no
danger of hazardous radiation outside the unit.
AC110–
120V
OUTPUT
SYSTEM
DIGITAL
CONTROL
OUT
L
SL16 XS 8
R
OPTICAL
AC110–
AC220–
120V
240V
Move switch lever to match your line voltage with a
small screwdriver or other pointed tool.
The marking of products using lasers
(Except for some areas)
CLASS 1
LASER PRODUCT
Introduction
CD-224M/DPF-J5010 (En)
AC220–
240V

Advertisement

Table of Contents

   Related Manuals for Kenwood DPF-J5010

This manual is also suitable for:

Cd-224m

Comments to this Manuals

Symbols: 0
Latest comments: