Faceplate Timer Features - Kenmore 625.3882 Owner's Manual

[i:ii:ii:ii:_i: i :ii:_I SECTION 2 I_i:ii:ii:ii:_i:i:ii:_]
HOW YOUR WATER SOFTENER WORKS
A. FACEPLATE TIMER FEATURES
S
C
T
N
,JJJJJJJJJJJJJJJJ.
,JJJJ JJJJJJJJJJ.
'dJ_idJdJdJdJ"
,JJ JJJJJJJJJ.
,JJJ JJJJJJJJJ.
,JJ JJJJJJJJJ.
,JJJJJJJJJJJJJJJJ.
,JJJJJJJJJJJJJJJJ.
EXTRA RECHARGE
Sometimes, a manually started
regeneration (recharge) may be
desired, or needed. Two exam-
ples are:
- You have used more water than
usual (guests visiting) and you
may run out of soft water before
the next timer started regenera-
tion.
- You did not refill the softener
with salt before it was gone. After
you refill with salt:
You can start a regeneration right
away, or you can set the timer to
regenerate at the next 2:00 AM (or
other preset recharge time). Do
the following.
RECHARGE NOW i°'I _
3,n_q _
_"
I'U!_-I
Press the ON/OFF-HOLD but- i/
._C.A.G_
ton and hold until *RECHARGE ..........
Serv and Fill begin to flash in the display. Upon
reaching fill the first cycle of regeneration, the flash-
ing Serv goes off and Fill is on steady. RECHARGE
continues to flash. This regeneration will last for
about 2 hours. After the 2 hours, you will have soft
water again.
*Note:
If the CLEAN feature is set to ON, a cleaning back-
wash (CLEAN and Bkwsh or Rinse flashes in the dis-
play, along with the minutes of the clean cycle re-
maining) precedes the recharge.
RECHARGE TONIGHT [ !°_ _:l-_n _-
Press and release (do not hold) the I i R_C._G_TO_G.,
ON / OFF-HOLD button. RE-
CHARGE TONIGHT flashes in the display, and the
softener begins regeneration at the next preset re-
charge time. Press and release the ON/OFF-HOLD
button once more if you deride to cancel the regen-
eration, and RECHARGE TONIGHT.
SALT MONITOR SYSTEM
The face plate timer has a low salt monitor with an
indicator light to remind you to refill the storage
tank with salt. To set this monitor system:
_1_ Lift the salt hole cover and level the salt in the
storage tank.
ffi
The salt level decal on the brinewell inside the
tank, has numbers from 0 to 8 (see drawing be-
low). Observe the number the leveled salt is at
or closest to.
m
Now, press the SALT LEVEL ADJUST button
until black bars display up to the salt level num-
ber. For example, the pictures below show the
salt level at 6.
!!
Finall3_ set the level you want the low salt indi-
cator light to come on. Press the SIGNAL LIGHT
ADJUST button until a (_) shows opposite this
number. In the example below, the light will
come on when the stored salt drops to level 2. At
level 2, the storage tank is about 1/3 full. This is
the lowest you should allow the stored salt level
to drop to (see note on page 1-6).
_'_ If you wish to turn the salt monitor off, press the
SIGNAL LIGHT ADJUST button until OFF
shows above.
Note:
For accurate salt monitor operation, always use
nugget or pellet water softener salt. See page 1- 6.
salt
level
bars, salt
level
8 ,
7 ,
6
brinewell
decal
RECHARGE
TONIGHT
RECHARGE
NOW
indicator light s_ ° w
2-1