Download Print this page

Water Inlet Hoses - Kenmore 4900 series Owner's Manual And Installation Instructions

Front-loading automatic washer
Hide thumbs

Advertisement

I
I
5. Wash any dirt or other material from the debris filter. Make
sure the drain pump propeller
behind the debris filter is not
blocked.
6. Replace the debris filter cap.
7. Replace the filter cover.
8.
Close up the opening of drain tube with cap.
9. Don't insert the drain tube in the hole.
Replace inlet hoses after five years of use to reduce the risk
of hose failure. Periodically
inspect and replace inlet hoses if
bulges, kinks, cuts, wear or leaks are found.
When replacing your inlet hoses, record the date of replacement.
Install and store your washer where it will not freeze. Because
some water may stay in the hoses, freezing can damage
your washer. If storing or moving your washer during freezing
weather, winterize
it.
Non=use or vacation care:
Operate your washer only when you are at home. If you will be
on vacation
or not using your washer for an extended
period of
To use washer
again:
1. Flush water pipes.
2.
Reconnect
water inlet hoses to faucets.
3. Turn on both water faucets.
Electrical
Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension
cord.
Failure to follow
these
instructions
can result in death,
fire, or electrical
shock.
4.
Plug in washer or reconnect
power.
5.
Run the washer through the Normal/Casual
cycle. Use only
HE High Efficiency detergent.
Use 1Athe manufacturer's
recommended
amount for a medium sized load.
To t_ansport
the washer:
1.
2.
3.
If washer will be moved during freezing weather, put in 1 qt (1
L) of R.V.-type antifreeze in the drum. Run washer on a Drain
& Spin cycle.
Unplug the power cord.
Disconnect
the drain hose from the drain system and attach
to rear panel clips.
4. Shut off both water faucets.
5.
6.
Disconnect
the water inlet hoses from faucets, then drain the
hoses and clip them to the rear panel of the washer.
IMPORTANT:
Call service.
Reinsert the shipping
bolts to
minimize
internal washer damage that may occur during
transportation.
Upon completion
of moving,
please do not
time, you should:
forget to remove shipping
bolts prior to installation,
and keep
[]
Unplug washer or disconnect
power,
them for future use. Unit must be transported
in the upright
position.
To avoid suspension
and structural
damage, your
[]
Turn off the water supply to the washer. This helps avoid
machine
must be properly set up for relocation
by a certified
accidental
flooding
(due to a water pressure surge) while you
technician.
are away.
......................................................................................................................................................
[]
Slightly open door to provide ventilation.
To winterize
washer:
Reinstalling
the washer
1. Follow the "Installation
Instructions"
to locate, level and
connect
the washer.
1. Put 1 qt (1 L) of R.V.-type antifreeze in the drum.
2. Run washer on a Drain & Spin cycle.
8.
Unplug washer or disconnect
power.
2,
Run the washer through the Normal/Casual
cycle to clean
the washer and remove the antifreeze, if used. Use only
HE High Efficiency detergent.
Use 1Athe manufacturer's
recommended
amount for a medium sized load.
4.
Shut off both water faucets.
5.
Disconnect
water inlet hoses from faucets and drain.
24
(Best 2)Keim_ore 592-49003-02902A-01
EN.i_dd
24
2011-03-23
/,_1i
9:39:58
I

Hide quick links:

Advertisement

loading