Korg Pa3XLe User Manual page 388

384 Effects
Chorus, Flanger, and Phaser (Cho/Fln Phaser)
30: Multitap Cho/Delay
(Multitap Chorus/Delay)
This effect has four chorus blocks with a different LFO phase.
You can create a complex stereo image by setting each block's
delay time, depth, output level, and pan individually. You can
also fix some of the chorus blocks to combine the chorus and
delay effects.
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In -Stereo Out
Left
Feedback
Tap1 Delay
Tap2 Delay
+
Tap3 Delay
Tap4 Delay
Right
180 [degree]
90 [degree]
270 [degree]
LFO: Triangle
LFO Frequency
a 0.02...13.00
[Hz]
Tap1 (000)
0...1000
[msec]
Depth 0...30
b
Level 0...30
L6...L1, C,
Pan
R1...R6
Tap2 (180)
0...1000
[msec]
Depth 0...30
c
Level 0...30
L6...L1, C,
Pan
R1...R6
Tap3 (090)
0...1000
[msec]
Depth 0...30
d
Level 0...30
L6...L1, C,
Pan
R1...R6
Tap4 (270)
0...1000
[msec]
Depth 0...30
e
Level 0...30
L6...L1, C,
Pan
R1...R6
Tap1 Feedback –100...+100
Src Off...Tempo
f
Amt –100...+100
Dry, 1:99...99:1,
Wet/Dry
Wet
g
Src Off...Tempo
Amt –100...+100
FX Amt
Level
Pan
Level
Pan
Level
Pan
Level
Pan
0 [degree]
FX Amt
Sets the speed of the LFO
Sets the Tap1 (LFO phase=0
degrees) delay time
Sets the Tap1 chorus depth
Sets the Tap1 output level
Sets the Tap1 stereo image
Sets the Tap2 (LFO phase=180
degrees) delay time
Sets the Tap2 chorus depth
Sets the Tap2 output level
Sets the Tap2 stereo image
Sets the Tap3 (LFO phase=90
degrees) delay time
Sets the Tap3 chorus depth
Sets the Tap3 output level
Sets the Tap3 stereo image
Sets the Tap4 (LFO phase=270
degrees) delay time
Sets the Tap4 chorus depth
Sets the Tap4 output level
Sets the Tap4 stereo image
Sets the Tap1 feedback amount
Selects the modulation source of
Tap1 feedback amount and effect
balance
Sets the Tap1 feedback amount and
modulation amount
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 366
Amount of modulation source
31: Ensemble
This Ensemble effect has three chorus blocks that use LFO to
create subtle shimmering, and gives three dimensional depth
and spread to the sound, because the signal is output from the
left, right, and center.
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
Left
+
Right
Shimmer
LFO
Speed 1...100
Src Off...Tempo
a
Amt –100...+100
Depth 0...100
Src Off...Tempo
b
Amt –100...+100
c Shimmer 0...100
Dry, 1:99...99:1,
Wet/Dry
Wet
d
Src Off...Tempo
Amt –100...+100
c: Shimmer
This parameter sets the amount of shimmering of the LFO wave-
form. Increasing this value adds more shimmering, making the
chorus effect more complex and richer.
Level
FX Amt
Ensemble
FX Amt
Sets the speed of the LFO
Selects a modulation source for LFO
speed
Sets the modulation amount of LFO
speed
Sets the depth of LFO modulation
Selects the modulation source of
the LFO modulation depth
Sets the modulation amount of the
LFO modulation depth
Sets the amount of shimmering of
the LFO waveform
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 366
Amount of modulation source
Ensemble LFO
Shimmer
Time