Korg Pa3XLe User Manual page 380

Professional arranger
Table of Contents

Advertisement

376
Effects
EQ and Filters (EQ/Filter)
c: Voice Top
d: Voice Center
e: Voice Bottom
These parameters assign vowels to the top, center, and bottom
position of the controller.
E.g.: When "Voice Top"=A, "Voice Center"=I, and
"Voice Bottom"=U:
If "Sweep Mode"is set to D-mod and Ribbon is selected as the
modulation source, moving your finger from the right to left of
the ribbon controller will change the sound from "a" to "i, " then
"u. "
If Sweep Mode is set to LFO, the sound will change cyclically
from "a" to "i, " "u, " "i, " then "a. "
Voice Bottom
A
U
JS X
D
-mod
Ribbon
– Max
JS +Y
JS –Y
Zero
etc...
f: Formant Shift
This parameter adjusts the frequency level to which the effect is
applied. If you wish to apply the effect to a higher-range sound,
set this parameter to a higher value; to apply the effect to a
lower-range sound, set this to a lower value.
f: Resonance
This parameter sets the intensity of resonance for the voice pat-
tern. A larger value will add more character to the sound.
Talking Modulator Control
Voice Center
Voice Top
A
I
E
O
+ Max
Zero
+ Max
16: Stereo Decimator
This effect creates a rough sound like a cheap sampler by lower-
ing the sampling frequency and data bit length. You can also
simulate noise unique to a sampler (aliasing).
Stereo In - Stereo Out
Left
Pre LPF
Resolution
D
-mod
Sampling Frequency
LFO
Pre LPF
Resolution
Right
Pre LPF
Off, On
a
High Damp [%] 0...100
Sampling Freq
1.00k...
[Hz]
48.00k
b
Src
Off...Tempo
–48.00k...
Amt
+48.00k
LFO Frequency
0.02...20.00
[Hz]
c
Src
Off...Tempo
–20.00...
Amt
+20.00
MIDI Sync
Off, On
MIDI,
BPM
40.00...
d
300.00
Base Note
r...w
Times
x1...x32
Depth
0...100
e
Src
Off...Tempo
Amt
–100...+100
f
Resolution
4...24
Output Level
0...100
Src
Off...Tempo
g
Amt
–100...+100
Dry, 1:99...99:1,
Wet/Dry
Wet
h
Src
Off...Tempo
Amt
–100...+100
a: Pre LPF
If a sampler with a very low sampling frequency receives very
high-pitched sound that could not be heard during playback, it
could generate pitch noise that is unrelated to the original sound.
Set "Pre LPF" to On to prevent this noise from being generated.
If you set the "Sampling Freq" to about 3 kHz and set "Pre LPF"
to Off, you can create a sound like a ring modulator.
f: Resolution
g: Output Level
If you set a smaller value for the "Resolution" parameter, the
sound may be distorted. The volume level may also be changed.
Use "Output Level" to adjust the level.
FX Amt
High Damp Output Level
Decimator
Decimator
High Damp Output Level
FX Amt
Selects whether the harmonic noise
caused by a decrease in sampling
frequency is generated or not
Sets the ratio of cut of the high
range
Sets the sampling frequency
Selects the modulation source of
the sampling frequency
Sets the modulation amount of the
sampling frequency
Sets the speed of the LFO
Selects a modulation source for LFO
speed
Sets the modulation amount of LFO
speed
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Selects the type of notes that
specify the LFO speed
Sets the number of notes that
specify the LFO speed
Sets the depth of the sampling
frequency LFO modulation
Selects the LFO modulation source
of the sampling frequency
Sets the LFO modulation amount of
the sampling frequency
Sets the data bit length
Sets the output level
Selects the modulation source for
the output level
Sets the modulation amount of the
output level
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 366
Amount of modulation source

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents