Installation And Application Guidelines; Partition Installation Example; Program; Programming Mode - Honeywell ADEMCO 6152RF Installation And Setup Manual

INSTALLATION AND APPLICATION GUIDELINES

For installation, consider the following:
• Locate the 6152RF in an area and at a height convenient for
user operation.
• The 6152RF must be at least 10 feet from the control panel
to ensure proper RF receiver operation.
• Local wireless keys (wireless keys programmed directly into
the 6152RF) may be used regardless of whether the RF
receiver in the 6152RF is enabled or disabled.
• If using bi-directional devices, be sure to enable the
transmitter module in the 6152RF (program address 7).
• If transmitters are programmed into the control panel, be
sure to enable the receiver (program address 6). (Do not
exceed the number of receivers supported by the control
panel.)

Partition Installation Example

An example of an installation using two 6152RF Keypad / Transceivers with 2-Way Wireless Devices (e.g., 5828V) on two Partitions is
shown below:
Partition #1
6152RF
Partition #1
System House ID = 1
5828 or 5804BD
Partition #1
House ID = 1

4. PROGRAM

To program the keypad, first enter the Programming Mode, select a programming address and set the programming options. Refer to
the tables below and on the following pages for details on entering Programming mode, default values and programming choices for
each option.
Table 5 – Programming Mode
Action
1. Enter Program Mode
Within 30 seconds of power up
or reboot, press and hold down
the and keys at
the same time for 3 seconds.
Note: Refer to Table 2 to reboot
the keypad.
2. Enter a Programming
Address
(See Program Address
column in Table 6)
3. Set programming options
Use the number and
navigation keys to set the
programming options.
CONTROL
PANEL
Partition #2
6152RF
Partition #2
Local House ID = 2
5828 or 5804BD
Partition #2
House ID = 2
Result
Enters the Program mode
at the Start screen and
the keypad beeps three
(3) times
Screen displays selected
programming address
Refer to Choices column
in Table 6.
• The keypad provides an on-board relay, programmed in the
keypad and operated by wireless key (see Wireless Key On-
Board Relay Assignment on page 5 for programming
details).
• If a local wireless key is programmed to arm/disarm or to
trigger a relay on the control panel, a user code must be
entered into the 6152RF. This user code must also be
programmed into the control panel.
• You must set the House ID only if you are using RF keypads
and/or bi-directional devices; AND the House ID Source is
the 6152RF (Local).
Table 4 – Partition Installation
Settings
Keypad: Must be assigned to
Partition 1 in the
control panel
House ID: Match Partition 1
House ID in the control
panel and House ID in
Wireless Device
House ID System
Source:
Receiver On
Enable:
Transmitter
On
Enable:
Display
- The keypad will not enter programming mode if the panel is
oo, - -
armed.
flash
alternately
- Press the
power up to enter the User mode. This mode allows individual
[If any other
local wireless keys to be enabled and disabled (useful if, e.g., a
numbers or
user accidentally loses a wireless key). Refer to the User
letters
Guide for instructions.
appear
- To enter keypad Programming mode after power up period,
press
reboot the keypad (see Table 2 on page 1) and try again
.)
after the keypad LEDs stop flashing.
- The keypad automatically exits the Program mode if no keys
are pressed for 90 seconds.
- (For example, enter [1] to go to Keypad Address; enter [2]
See
to go to Receiver Address).
Display
column in
Table 6.
- Press
back.
- Press
beeps twice and the screen returns to Start
- 2 -
6152RF #1 6152RF #2
Must be assigned to
Partition 2 in the control
panel
Match House ID in
Wireless Device
Local
Off
On
Notes
and keys 60 seconds or more after
to erase the current information and move
to store the displayed information, the keypad