Codabar; Enable/Disable Codabar; Set Lengths For Codabar - Philips Pocket Memo DPM8500 Configuration Manual

Enable/Disable Codabar

Codabar

Parameter # 07h
13 Codabar
Enable/Disable Codabar
To enable or disable Codabar, scan the appropriate bar code below.
Parameter # 07h
Enable/Disable Codabar
To enable or disable Codabar, scan the appropriate bar code below.
Parameter # 07h
To enable or disable Codabar, scan the appropriate bar code below.

Set Lengths for Codabar

Parameter # L1 = 18h L2 = 19h
Set Lengths for Codabar
Set Lengths for Codabar
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
contains. Lengths for Codabar may be set for any length, one or two discrete lengths, or lengths within a specific range. To
Parameter # L1 = 18h L2 = 19h Parameter # L1 = 18h L2 = 19h
set lengths via serial commands, see
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Lengths for
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
Codabar may be set for any length, one or two discrete lengths, or lengths within a specific range.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select
contains. Lengths for Codabar may be set for any length, one or two discrete lengths, or lengths within a specific range. To
Codabar One Discrete Length, then scan 1, 4, to decode only Codabar symbols containing 14 characters. Numeric bar
set lengths via serial commands, see
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select Codabar One Discrete Length,
codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan
then scan 1, 4, to decode only Codabar symbols containing 14 characters. Numeric bar codes begin on page 56. To change the selection or cancel
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select
an incorrect entry, scan Cancel on page 57.
Codabar One Discrete Length, then scan 1, 4, to decode only Codabar symbols containing 14 characters. Numeric bar
codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan
Codabar (continued)
Two Discrete Lengths - This option sets the unit to decode only those codes containing two selected lengths. For
Codabar (continued)
Two Discrete Lengths - This option sets the unit to decode only those codes containing two selected lengths. For example, select Codabar Two
example, select Codabar Two Discrete Lengths, then scan 0, 2, 1, 4, to decode only Codabar symbols containing 6 or
Discrete Lengths, then scan 0, 2, 1, 4, to decode only Codabar symbols containing 6 or 14 characters. Numeric bar codes begin on page 56. To
14 characters. Numeric bar codes begin on
change the selection or cancel an incorrect entry, scan Cancel on page 57.
on page 4-74.
Two Discrete Lengths - This option sets the unit to decode only those codes containing two selected lengths. For
example, select Codabar Two Discrete Lengths, then scan 0, 2, 1, 4, to decode only Codabar symbols containing 6 or
14 characters. Numeric bar codes begin on
on page 4-74.
Length Within Range - Select this option to decode a code within a specified range. For example, to decode Codabar
symbols containing between 4 and 12 characters, first scan Codabar Length Within Range, then scan 0, 4, 1 and 2
(single digit numbers must always be preceded by a leading zero). Numeric bar codes begin on
Length Within Range - Select this option to decode a code within a specified range. For example, to decode Codabar
Length Within Range - Select this option to decode a code within a specified range. For example, to decode Codabar symbols containing between 4
selection or cancel an incorrect entry, scan
symbols containing between 4 and 12 characters, first scan Codabar Length Within Range, then scan 0, 4, 1 and 2
and 12 characters, first scan Codabar Length Within Range, then scan 0, 4, 1 and 2 (single digit numbers must always be preceded by a leading zero).
(single digit numbers must always be preceded by a leading zero). Numeric bar codes begin on
Numeric bar codes begin on page 56. To change the selection or cancel an incorrect entry, scan Cancel on page 57.
selection or cancel an incorrect entry, scan
Any Length - Scan this option to decode Codabar symbols containing any number of characters.
Any Length - Scan this option to decode Codabar symbols containing any number of characters.
Any Length - Scan this option to decode Codabar symbols containing any number of characters.
Barcode scanner configuration guide
Enable Codabar
(01h)
Enable Codabar
(01h)
*Disable Codabar
(00h)
*Disable Codabar
(00h)
Setting Code Lengths Via Serial Commands on page
Setting Code Lengths Via Serial Commands on page
Codabar - One Discrete Length
Codabar - One Discrete Length
page 4-73. To change the selection or cancel an incorrect entry, scan
page 4-73. To change the selection or cancel an incorrect entry, scan
Codabar - Two Discrete Lengths
Codabar - Two Discrete Lengths
Cancel on page 4-74.
Cancel on page 4-74.
Codabar - Length Within Range
Codabar - Length Within Range
A-7.
A-7.
Cancel on page 4-74.
Parameter Menus 4 - 59
Cancel on page 4-74.
Parameter Menus 4 - 59
page 4-73. To change the
page 4-73. To change the
Cancel
Cancel
49