Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for RAMSET T2
Summary of Contents for RAMSET T2
- Page 2 Just as no one can merely read a book about driving an automobile and then hope to drive one safely, no one should attempt to use the T2 gas powered tool without adequate, competent personal instruction. No automobile instruction book or instructor can forewarn a learner against all possibilities and emergencies, nor can printed material detail all possible conditions surrounding the use of Ramset tools and products.
-
Page 3: Safety Introduction
SAFETY INTRODUCTION CONTENTS SAFETY INSTRUCTIONS FASTENING APPLICATIONS TOOL OPERATING INSTRUCTIONS PARTS SCHEMATIC 10-11 PARTS LIST 12-13 SERVICING/TROUBLESHOOTING WARRANTY... - Page 4 • Poured Concrete • Structural Steel • Concrete Block and Horizontal Joints Fastening into other materials can cause blindness or other serious injury. These materials can shatter, causing the fastener and/or base material fragments to fly free and cause serious injury to the tool operator and others. Failure to assure the suitability of the base material can result in serious injury to the eyes or other body parts.
- Page 5 • The fuel cell must be used at • At the beginning of each fastening • The fuel cell is designed with an • When the fuel cell is empty, a • For safety and proper tool functioning • The battery will become discharged • Remove the battery from the tool • Recharge the battery if it has not • Batteries are supplied in an • Do not recharge batteries until • It takes about 1 hour to recharge • Use only batteries and chargers • Battery Capacity—Maximum...
- Page 6 • Insert the battery into the tool • Note the LED light on the right • There is a cap located on the rear of • Insert the fuel cell, nose first, all the • Replace the cap by lining up the...
- Page 7 • Use the tool only in well ventilated • Always hold the tool at right angles • Never attempt to make a fastening • While the tool can be used in any • Never put your hand over the nose • Never put your hand on or over the • Never carry the tool with your finger • Never leave the tool unattended or 90° • Never engage in horseplay with • Always keep the tool pointed away • Never operate the tool if explosive • Keep the tool and supplies locked...
- Page 8 Your T2 tool can be used for a wide 3" MIN. range of fastening needs in a variety of base materials. Reading and following these important fastening guidelines will help you get the best results from your tool and fasteners, as well as help you perform these fastening operations safely and effectively.
- Page 9 1. Insert a charged battery into the tool with the battery clip toward the rear of the tool. 2. Insert the Ramset fuel cell into the tool as described on page 6. 3. Pull the magazine follower back to the locking position.
- Page 11 (continued)
-
Page 12: Cylinder Head
336920 GRILL CAP 336900 AIR FILTER B0060A CAP SCREWS M5-30 W/WASHER 339000 CAP ASSEMBLY B0070 SPARK PLUG WIRE B0061A PC BOARD SCREWS, M4-12 B0040 PC BOARD 7505164 SPARK PLUG ASSEMBLY 900525A FAN MOTOR ASSEMBLY (INCLUDES FAN, MOTOR SLEEVE, MOTOR MOUNT, RETAINING RING AND FAN BLADE) 401356 MOTOR SLEEVE 900470... - Page 13 FUEL CELL CUP BRACKET EM150340A FUEL CELL RETAINING CUP ASSEMBLY — B0058 GUIDE BLOCK SCREW — B0072 FUEL CONNECTOR SCREW M4-8 — B0073 UPPER EXHAUST SCREW — B0057 CAGE SCREW T2OM T2 OPERATORS MANUAL 334000 BATTERY 7505142 BATTERY CHARGER W/WALL MOUNT ADAPTOR...
- Page 14 Cleaning the filters and battery contacts on a regular basis will help make your tool work more efficiently. • Remove the cover and the filters. • Lightly tap the filters to remove any dust. • Replace the filters if damaged. •...
- Page 15 • Bumper • Piston Assembly • O-Rings • Piston Rings...
-
Page 16: Printed In The U.s.a
© ILLINOIS TOOL WORKS 2008 PRINTED IN THE U.S.A. REVISED 11/08 Form No. SM-T2-11/08...
Need help?
Do you have a question about the T2 and is the answer not in the manual?
Questions and answers