Pdc Recording - JVC HR-S9700EK Instruction Manual

ENTER PRESET POSITION
6
Press PR +/– to enter the
preset position corre-
sponding to the broadcast-
ing station you wish to
record.
SET TAPE SPEED
7
Press SP/LP/EP (
SET PDC MODE
8
Press PDC to select "ON" or "OFF".
If "VPS/PDC ON" is displayed on the screen or "VPS/
PDC" is lit on the display panel, PDC is set to ON.
If "VPS/PDC OFF" is displayed on the screen or "VPS/
PDC" is not lit on the display panel, PDC is set to OFF.
"PDC Recording" in the right column.
VPS (Video Programme System) recording is not
currently available in the U.K. and not possible with
this recorder.
RETURN TO NORMAL
SCREEN
9
After confirming all information is correct, press PROG
or OK. "PROGRAM COMPLETED" appears on the
screen for about 5 seconds, then normal screen
appears. If the timer programme is overlapped with
another one that was already set, "PROGRAM
OVERLAPPED" appears on screen and "Err" appears on
the front display panel. (
Repeat steps 1 – 9 for each additional programme.
ENGAGE RECORDER'S
TIMER MODE
10
Press ‰ (TIMER). The recorder turns off automatically
and ‰ appears on the display panel. The ‰ indicator
on the recorder's front panel also lights up.
To disengage the timer, press ‰ (TIMER) again.
To Timer-Record Weekly Or Daily Serials . . .
. . . anytime during steps 2 through 9, press WEEKLY (NUMBER
key "9") for weekly serials or DAILY (NUMBER key "8") for
daily serials (Monday – Friday). Either "WEEKLY" or "DAILY"
appears on the screen. Pressing the button again makes the
corresponding indication disappear.
NOTE:
You can programme this recorder to timer-record as many as 8
programmes. If you try to programme the recorder to record a
ninth, "PROGRAM FULL" appears on screen and "FULL" appears
on the front display panel. To record the extra programme, you
must first cancel any unnecessary programmes (
– P1 –
START STOP
=
21:00 22:00
SP VPS/PDC OFF
DATE TV PROG
25.12
BBC 1
[+/–] =
[0]:SAT
[PROG] : EXIT
SP
) to set the tape speed.
pg. 23)
pg. 22).
Satellite Receiver Users
To timer-record a satellite broadcast using Express Timer
Programming:
1 Perform "Satellite Receiver Control Setting" (
2 Perform steps 1 – 10. In step 6, press the NUMBER key
"0" to change "TV PROG" to "SAT". The display panel
shows "L2" for the preset position. Then press PR +/– to
enter the preset position for the satellite broadcast. In
1
step 8, you cannot set PDC to ON.
3 Leave the satellite receiver's power on.

PDC Recording

Now available from some TV stations, PDC (Programme
Delivery Control) is a service designed to assure safe,
accurate timer recording. With this system, special code
signals are transmitted together with the audio/video
signals. These code signals control your video recorder and
have precedence over the advertised times which you may
have preset into the timer. This means that your recorder
will start and stop recording when the preset TV
programmes actually start and end — even if the broadcast
time of a preset TV programme is changed from what has
been advertised. PDC is currently available nationally on
BBC1, BBC2, Ch.4 and Ch.5, except from a few small relay
transmitters. Ch.3 operates a PDC service in some areas.
All channels intend to offer this service in due course.
Check your TV programme listing guide for latest informa-
tion. If the channel you intend to record does not offer a
PDC service your recorder will not start recording if PDC
has been selected. Be sure to set PDC to "OFF" if PDC is
not available on your selected channel.
( step 8 in the left column).
NOTES:
Set the start time (PDC time) exactly as advertised in the
TV listing. A different time than advertised will result in
no recording.
PDC recording is also possible when a satellite receiver or
a cable system is connected to AV2 (L-2) IN/DECODER on
your recorder.
PDC recording is also possible via the AV1 (L-1) IN/OUT
connector.
Timer Warning
If you have programmed your
recorder to timer-record a
programme or a series of
programmes, a warning
appears on the screen to tell
you that the recording is due
to start in 5 minutes.
NOTES:
The warning only appears if you're not in the Timer
mode at the time.
If this recorder is being used as the player for tape
dubbing, the warning screen will be recorded on the
tape in the other video recorder.
The warning blinks for the entire 5 minutes leading up to
the start of timer recording. To clear the display, press
21
pg. 12).
– WARNING–
TIMER RECORDING
TO START SOON
[ ]
.