Kenwood TK-7100 Service Manual page 7

No. Function Choices
2 RX Off - - - - - - - -
signalling
QT 67.0~254.1 Q T
QT 254.1✽
(0.1Hz step mode)
Q T
QT 67.0~250.3
(EIA mode) Q T 2 5 0 . 3
DQT 000~777 DQT000N✽
Normal DQT777N✽
(1 step mode)
D Q T 0 2 3 N
DQT 023~754
D Q T 7 5 4 N
Normal
(Standard
table mode)
D Q T 0 0 0 Ι ✽
DQT 000~777
D Q T 7 7 7 Ι ✽
Inverse
(1 setp mode)
D Q T 0 2 3 Ι
DQT 023~754
D Q T 7 5 4 Ι
Inverse
(Standard
table mode)
S T P
3 TX Step 2.5kHz~
S T P
frequency 1MHz
T . – – – – – – –
Blank
T.150.0000
100.0000~
550.0000MHz
- - - - - - - -
4 TX Off
signalling
QT 67.0~254.1 Q T
(0.1Hz step mode) QT 254.1✽
QT 67.0~250.3 Q T
Q T 2 5 0 . 3
(EIA mode)
DQT000N✽
DQT 000~777
DQT777N✽
Normal
(1 step mode)
DQT 023~754 D Q T 0 2 3 N
Normal D Q T 7 5 4 N
(Standard
table mode)
REALIGNMENT
Display Remarks
key : Off/QT/DQT
switching
6 7 . 0✽
6 7 . 0
key : Hold 1 second
to switch between
Normal/Inverse.
2 5 0
Display when an item
1 M
is selected or a step is
changed (about 0.5
seconds).
key : Select the
frequency step
key : Hold 1 second
to frequency on/blank
switching.
The right most dot
indicates 50Hz digit.
(On=5, Off=0)
key : Off/QT/DQT
switching
6 7 . 0✽
6 7 . 0
No. Function Choices
D Q T 0 0 0 Ι ✽
DQT 000~777
D Q T 7 7 7 Ι ✽
Inverse
(1 setp mode)
D Q T 0 2 3 Ι
DQT 023~754
D Q T 7 5 4 Ι
Inverse
(Standard
table mode)
5 Option Off N O N E
D T M F
signalling DTMF
6 SP Carrier S.UM CARR
unmute QT/DQT S.UM QTDQ
Carrier+DTMF S.UM C+DT
S.UM Q+DT
QT/DQT+
DTMF
7 Busy Off B C L O F F
channel Carrier B C L C A R R
lockout QT/DQT BCL QTDQ
BCL DTMF
DTMF
8 Beat No S H F T N O
Yes S H F T Y E S
P W R H
9 RF High power
power Low power P W R L
10 Wide/ Wide W I D E
Narrow Narrow NARROW
11 Scan Delete S C A N D E L
Del/Add Add SCAN ADD
12 Priority No P.CH
channel Yes P.CH
13 PTT ID Off P . I D O F F
Begin of TX P . I D B O T
P . I D E O T
End of TX
Both P.ID BOTH
14 Scrambler Off S C R O F F
No S C R O N
15 Scrambler 1~16 S C R
code S C R
• Finish beep will sound when displayed data is stored.
• The settings for scrambler and scrambler code can only be
selected when voice scrambler board is installed.
TK-7100
Display Remarks
key : Hold 1 second
to switch between
Normal/Inverse.
Default
Not used when QT/
DQT decode is not set.
Not used when option
signalling is none.
Not used when option
signalling is none.
Default
If QT/DQT decode is
not set, it cannot be
selected.
If option signalling is
set to off, it cannot be
selected.
Default
Default
Default
Default
NO Default
YES Not used when scan
priority is not fixed.
Default
Default
1 Default
1 6
7