Delta Shopmaster GR050 Instruction Manual
  1. Manuals
  2. Brands
  3. Delta Manuals
  4. Power Tool
  5. Shopmaster GR050
  6. Instruction manual

Delta Shopmaster GR050 Instruction Manual

Utility sharpener
Hide thumbs
Table of Contents

Advertisement

Quick Links

Utility Sharpener
(Model GR050)
PART NO. 906996 - 08-06-02
Copyright © 2002 Delta Machinery
To learn more about DELTA MACHINERY
ESPAÑOL: PÁGINA 11
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
1-800-223-7278 (
1-800-463-3582).
please call
In Canada call

Advertisement

Table of Contents
loading

Related Manuals for Delta Shopmaster GR050

Summary of Contents for Delta Shopmaster GR050

  • Page 1 Utility Sharpener (Model GR050) PART NO. 906996 - 08-06-02 Copyright © 2002 Delta Machinery To learn more about DELTA MACHINERY ESPAÑOL: PÁGINA 11 visit our website at: www.deltamachinery.com. For Parts, Service, Warranty or other Assistance, 1-800-223-7278 ( 1-800-463-3582). please call...

  • Page 2: General Safety Rules

    If you have any questions relative to a particular application, DO NOT use the machine until you have first contacted Delta to determine if it can or should be performed on the product.
  • Page 3 ADDITIONAL SAFETY RULES FOR UTILITY SHARPENERS WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY. 1. DO NOT OPERATE THIS MACHINE until it is 11. NEVER START THE MACHINE with the workpiece assembled and installed according to the against the grinding wheel.

  • Page 4: Power Connections

    POWER CONNECTIONS GROUND FAULT CIRCUIT INTERRUPTER (GFCI) PROTECTION SHOULD BE PROVIDED ON THE CIRCUIT(S) OR OUTLET(S) TO BE USED FOR THE UTILITY SHARPENER. A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching receptacle which will accept the machine’s plug.

  • Page 5: Extension Cords

    Fig. D OPERATING INSTRUCTIONS FOREWORD Delta ShopMaster Model GR050 Utility Sharpener is a valuable addition to any shop. The Utility Sharpener can be used to sharpen most flat cutting tools. UNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces.
  • Page 6 UTILITY SHARPENER COMPONENTS Fig. 2 1. Forward / Off / Reverse Control Switch 2. Front Tool Rest 3. Front Tool Rest Adjusting Screws 4. Hex Wrench 5. Rear Tool Rest Adjusting Screws 6. Rear Tool Rest 7. Grinding Wheel...
  • Page 7 FILLING UTILITY SHARPENER WITH WATER WARNING: DISCONNECT MACHINE FROM POWER SOURCE. Place the utility sharpener on a flat surface. Loosen the the front tool rest adjusting screw (A) Fig. 3, and move the front tool rest away from the grinding wheel. Pour approximately 3 ounces of water into the front of water trough (B) Fig.

  • Page 8: Operating Controls And Adjustments

    OPERATING CONTROLS AND ADJUSTMENTS STARTING AND STOPPING UTILITY SHARPENER The “Forward / Off / Reverse” switch (A) Fig. 6, is located toward the front of the machine. To turn the machine “ON”, move the switch to the “Forward” or “Reverse” position.
  • Page 9 NOTES...

  • Page 10: Parts, Service Or Warranty Assistance

    Two Year Limited Warranty Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two years and provides Delta with reasonable opportunity to verify the alleged defect by inspection.

Table of Contents