Download Print this page

Volkswagen 2004 Golf Workshop Manual: Removing And Installing Drive Shafts

Hide thumbs
   
1
2
Table of Contents
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418

Advertisement

6

Removing and installing drive shafts

Removing and installing drive shaft with constant velocity joint
⇒ page 79
.
Removing and installing left drive shaft with (push-on) constant
velocity slip joint
⇒ page 81
Removing and installing right drive shaft with (push-on) constant
velocity slip joint
⇒ page 85
Removing and installing drive shafts with triple roller joint
AAR2600i
⇒ page 88
.
Removing and installing drive shafts with triple roller joint
AAR3300i
⇒ page 90
.
Removing and installing intermediate shaft
WARNING
When removing and installing drive shafts, do not allow them
to hang free and stop against joints due to over bending.
6.1
Loosening and tightening drive shaft
hexagon bolt
Special tools and workshop equipment required
♦ Torque/angle wrench -V.A.G 1756-
Wheel bearings must not be subjected to load after bolt securing
drive shaft to wheel hub has been loosened.
If wheel bearings are loaded with weight of vehicle, bearing will
be damaged. This reduces the service life of the wheel bearing.
It is therefore important to note the following:
♦ Procedure for loosening hexagon bolt.
Do not attempt to move the vehicle without the drive shafts fitted
as this would result in wheel bearing damage. If the vehicle does
have to be moved, always note the following points:
– Fit an outer joint in place of drive shaft.
– Tighten outer joint to 120 Nm.
Loosening hexagon bolt
– For vehicles which are still standing on their wheels, loosen
the hexagon bolt a maximum of 90°, as the wheel bearing will
otherwise be damaged.
– Raise vehicle so that wheels are off the ground.
– Have second mechanic apply brakes.
.
.
⇒ page 92
Golf 2004 ➤ , Golf Plus 2005 ➤
Running gear, axles, steering - Edition 08.2009
.
6. Removing and installing drive shafts
77

Advertisement

This manual also for:

2005 golf plus

Comments to this Manuals

Symbols: 0
Latest comments: