JVC RM-LP25U Instructions Manual page 10

Getting Started
Names and Functions of Parts
(continued)
Control Panel (continued)
A
O O P P E E R R A A T T E E
B
S S C C E E N N E E F F I I L L E E
C
1 1 2 2
PART PART
D NOR NOR
0 0
E
-3 -3
F
L L E E V V E E L L G G A A M M M M A A
G
B B L L A A C C K K
H
C C O O M M P P R R E E S S S S S S T T R R E E T T C C H H
R R
I
R R
J
K
L
M
SET SET
AUTO AUTO
F F U U L L L L
T T A A L L L L Y Y
O
C C A A L L L L P P R R E E V V I I E E W W
P
Q
N
L L O O C C K K B B A A R R S S
P P A A R R T T
O O F F F F F F U U L L L L
SPEED SPEED
3 3 4 4 5 5
R R
1/1000 1/1000 1/20 1/20
A A U U T T O O
L L E E V V E E L L D D E E T T A A I I L L K K N N E E E E P P O O I I N N T T
K K N N E E E E
AW B AW B
W A W A
PAINT PA NT AUTO WH TE AUTO WHITE
AUTO BLACK AUTO BLACK
PAINT PA NT
PART PART PART
OVER OVER OPEN OPEN
UN UN
CLO O S S S E CLOSE E
STER STER
ACK ACK
J
Black Balance Control Unit (A 18 page)
For specifying the black balance settings.
[AUTO BLACK] Auto Black button:
Pressing this button when it lights up in green switches the
color to orange and starts up the auto black feature.
After the adjustment is complete, the result is indicated by the
indicator.
Lights up in green
Blinks in orange
B Lights up in green
Note:
● The feature is not available on the camera if the light of the corresponding
S
button is not lit. Control using this unit is disabled in this case.
[PAINT] Paint button and indicator light:
For specifying whether fine-tuning is to be performed on the
value stored at the camera.
ON
(Orange light on)
OFF
(Green light on)
Note:
R
● The feature is not available on the camera if the light of
the corresponding button is not lit. Control using this unit
is disabled in this case.
[BLACK PAINT R/B] Black Paint R/B adjustment knob:
For adjusting the R and B levels when the [PAINT] button
lights up in orange.
K
Iris Control Unit
[IRIS MODE] Iris Mode Setting Switch
For selecting an iris mode.
FULL : Sets the camera to the manual iris mode.
PRESET : Sets the camera to the manual iris mode.
AUTO
Memo:
● When the Gain control unit E is set to ALC , the iris
mode becomes AUTO regardless of the switch setting.
(factory setting) When ALC is selected, however, it is
still possible to operate the camera according to the status
of the iris mode setting switch. (A 24 page)
: Auto black is successfully
completed.
: Auto black is abnormally
terminated.
: Fine-tuning enabled.
Adjust by turning the [BLACK
PAINT R/B] knob.
: Fine-tuning disabled.
The [BLACK PAINT R/B] knob is disabled.
Adjust using the iris setting lever M.
(CLOSE-OPEN)
Set the variable iris range using the iris setting
lever M to any 4-f/stops (approximately)
range between CLOSE and OPEN.
The setting range is ± 2-f/stops from the center value
that is specified using the preset level setting knob.
Sets the camera to the auto iris mode. Adjust
the auto iris level using the iris setting lever M.