JVC RX-8000VBK Instructions Manual page 53

Audio/video control receiver
Table of Contents

Advertisement

To change the transmittable signals for
operating another manufacturer's VCR
1. Set the remote control mode to "AUDIO/TV/
VCR."
2. Press and hold VCR 1 POWER.
3. Press VCR 1.
4. Enter manufacturer's code (two digits) using
buttons 1–9, and 0.
See the list below to find the code.
Examples: For a JVC product, press 0, 1.
For an NEC product, press 2, 5.
5. Release VCR 1 POWER.
The following button can be used for operating the VCR (with
the remote control mode selector set to "AUDIO/TV/VCR"):
VCR 1 POWER Turns on and off the VCR.
After pressing VCR 1 or VCR 1 CONTROL (with the remote
control mode selector set to "AUDIO/TV/VCR"), you can
perform the following operations on the VCR 1:
CHANNEL +/– Changes the TV channels on the VCR.
1 – 10, 0, 100+ (+10)
PLAY
Starts playback.
1
Rewinds a video tape.
¡
Fast winds a video tape.
STOP
Stops operation.
PAUSE
Pauses.
¶ REC:
Starts recording or enters recording pause.
Notes:
• Refer to the manual supplied with your VCR.
• You can use either VCR 1 button or the VCR 1 CONTROL
button to activate the buttons listed above. If you press VCR 1,
the playing source also changes. On the other hand, if you
press VCR 1 CONTROL, the playing source does not change.
6. Try to operate your VCR by pressing VCR 1
POWER.
When your VCR turns on or off, you have entered the correct
code.
If there are more than one code listed for your brand of
VCR, try each one until the correct one is entered.
Manufacturer
Codes
JVC
01, 02, 03
EMERSON
11, 26
FISHER
29
FUNAI
10, 14, 15, 16
GOLD STAR
12
HITACHI
04
MITSUBISHI
13
NEC
25
PANASONIC
07, 17
Manufacturers' codes are subject to change without notice. If they
are changed, this remote control cannot operate the equipment.
Selects the TV channels.
The 100+ (+10) button will function
as the ENTER button if your VCR
requires pressing ENTER after
selecting a channel number.
Manufacturer
PHILIPS
09
RCA
05, 06
SAMSUNG
24
SANYO
21, 22, 23
SHARP
27, 28
SHINTOM
30
SONY
18, 19, 20
ZENITH
08
To change the transmittable signals for
operating a DVD player
1. Set the remote control mode to "AUDIO/TV/
VCR."
2. Press and hold VCR 1 POWER.
3. Press DVD.
4. Enter manufacturer's code (two digits) using
buttons 1–9, and 0.
See the list below to find the code.
Examples: For a JVC product, press 0, 1.
5. Release VCR 1 POWER.
After pressing DVD or DVD MULTI (with the remote control
mode selector set to "AUDIO/TV/VCR"), you can perform the
following operations on a DVD player:
PLAY:
Starts playing.
4:
Returns to the beginning of the current (or previous)
track.
¢:
Skips to the beginning of the next track.
STOP:
Stops playing.
PAUSE: Stops playing temporarily. To release it, press PLAY.
After pressing DVD, these buttons
can be used for the DVD menu
operations.
Note:
For detailed menu operations, refer to the
instructions supplied with the discs or the
DVD player.
Note:
Refer to the manual supplied with your DVD player.
6. Try to operate your DVD player by pressing one
of the above buttons.
• DO NOT forget to turn on the DVD player before pressing
one of the above buttons.
Manufacturer
JVC
PANASONIC
PHILIPS
Codes
PIONEER
SONY
TOSHIBA
YAMAHA
Manufacturers' codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
For a SONY product, press 0, 5.
TEST
4
01
02
07
03
05
04
06
CENTER
2
3
MENU
MENU
REAR-L
5
6
ENTER
ENTER
REAR-R
8
Codes
51

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Rx-8000vbkj

Table of Contents