Operating Jvc's Audio/Video Components - JVC RX-558VBK Instructions Manual

Operating JVC's Audio/Video Components

You can operate JVC's audio and video components with this receiver's remote control, since control signals for JVC
components are preset in the remote control.
IMPORTANT:
To operate JVC's audio components using this remote control:
• You need to connect JVC audio components through the COMPU
LINK-3 (SYNCHRO) jacks (see page 21) in addition to the
connections using cables with RCA pin plugs (see page 5).
• Aim the remote control directly at the remote sensor on the
receiver.
• If you use the buttons on the front panel to choose a source, the
remote control will not operate that source. To operate a source
with the remote control, the source must be selected using buttons
on the remote control.
• Refer also to the manuals supplied with your components.
CD TV
TAPE/MD
DELAY
FM/AM EFFECT
4
VCR
7/P
SOUND
DVD CONTROL
DVD MULTI CD-DISC
PHONO TV/VIDEO
ONE TOUCH
OPERATION
MUTING
SLEEP
8
4
1
RM-SR558U REMOTE CONTROL
Tuner
After pressing FM/AM, you can perform the following operations:
FM/AM:
Alternates between FM and AM.
1 – 10, +10: Selects a preset channel number directly.
For channel number 5, press 5.
For channel number 15, press +10, then 5.
For channel number 20, press +10, then 10.
22
POWER
VCR AUDIO
TEST SURROUND
5
1 2 3
– CENTER +
5 6
– REAR•L +
5
8 9
MENU
– REAR•R +
10 +10
ENT
TV VOL.
– +
TV CH
– +
+
+
VOLUME VCR CH
– –
£
4
1
7
Sound control section (Amplifier)
After pressing SOUND CONTROL, you can perform the following
operations:
SURROUND: Selects the DSP modes.
CENTER – / +: Adjusts the center speaker output level for the
Surround/DVD MULTI playback modes.
REAR•L – / +: Adjusts the left/right rear speaker output level for
the DSP modes.
Adjusts the left rear speaker output level for the
DVD MULTI playback mode.
REAR•R – / +: Adjusts the right rear speaker output level for the
DVD MULTI playback mode.
DELAY: Selects the delay time of the rear speaker sound.
(Only works when "PROLOGIC" is selected.)
EFFECT: Selects the effect level for the DSP modes.
TEST:
Turns on or off the test tone output for the
Surround mode.
Note:
After adjusting sounds, press the corresponding source selecting
button or CD-DISC to operate your target source by using the 10
keys; otherwise, the 10 keys cannot be used for operating your target
source.
CD player
After pressing CD, you can perform the following operations on the
CD player:
3:
Starts playing.
4 4
4 : 4 4
Returns to the beginning of the current (or
previous) track.
¢ ¢
¢ ¢ ¢ :
Skips to the beginning of the next track.
7:
Stops playing.
8: Pauses playing. To release it, press 3.
1 – 10, +10:
Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
CD player-changer
After pressing CD-DISC, you can perform the following operations
on a CD player-changer:
3:
Starts playing.
4 4 4 :
4 4
Returns to the beginning of the current (or
previous) track.
¢ ¢
¢ : ¢ ¢
Skips to the beginning of the next track.
7:
Stops playing.
8: Pauses playing. To release it, press 3.
1 – 6, 7/P: Selects the number of a disc installed in a CD
player-changer.
After pressing CD, you can perform the following operations on the
CD player-changer:
1 – 10, +10:
Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.