Kyocera KM-3050 Service Manual page 148

2GN/2GP/2GR
Section Description
Optional 83
finisher Exit sensor stay jam
84
Jam in eject section of
right sub tray (3000-
sheet document fin-
isher only)
85
Jam in eject section of
left sub tray (3000-
sheet document fin-
isher only)
86
Jam in eject section of
internal tray 1 (3000-
sheet document fin-
isher only)
87
Jam in eject section of
internal tray 2 (3000-
sheet document fin-
isher only)
88
Jam in eject section of
main tray (3000-sheet
document finisher only)
1-4-8
Conditions
(3000-sheet document finisher)
Eject switch 1 (ESW1) is not turned off within specified
time of its turning on.
(Document finisher)
In the straight mode, the exit sensor (EXS) is not turned
off within specified time of its turning on.
(Document finisher)
In the offset or staple mode, the exit sensor (EXS) is not
turned off within specified time of its turning on.
(Built-in finisher)
The paper conveying switch (PCSW) does not turn off
within specified time of its turning on when paper is
ejected to the finisher tray from the intermediate tray.
Eject switch 2 (ESW2) is not turned off even if a specified
time has elapsed after the machine eject signal was
received.
Eject switch 2 (ESW2) is not turned on even if a specified
time has elapsed after the machine eject signal was
received.
Eject switch 2 (ESW2) is not turned off within specified
time of its turning on.
Eject switch 3 (ESW3) does not turn off within specified
time of paper entry sensor (PES) turning on.
Eject switch 3 (ESW3) does not turn on within specified
time of paper entry sensor (PES) turning on.
Eject switch 3 (ESW3) is not turned off within specified
time of its turning on.
Internal tray entry sensor 1 (ITPES1) is not turned on
even if a specified time has elapsed after the eject signal
was received.
Internal tray entry sensor 2 (ITPES2) does not turn on
within specified time of internal tray entry sensor 1
(ITPES1) turning on.
Internal tray entry sensor 2 (ITPES2) does not turn off
within specified time of internal tray entry sensor 1
(ITPES1) turning off.
Eject switch 1 (ESW1) is not turned on within specified
time.
Side registration home position sensor 1 (SRHPS1) is not
turned off within specified time of its turning on.
Side registration home position sensor 2 (SRHPS2) is not
turned off within specified time of its turning on.
The paper conveying belt detection sensor (PCBDS) is
not turned off within specified time.
Specified time
1182 ms
1680 ms
5375 ms
Paper length +
1123 ms (30 ppm)
Paper length +
869 ms (40/50 ppm)
1562 ms (30 ppm)/
1209 ms (40/50 ppm)
1562 ms (30 ppm)/
1209 ms (40/50 ppm)
2989 ms (30 ppm)/
2313 ms (40/50 ppm)
1843 ms (30 ppm)/
1426 ms (40/50 ppm)
1843 ms (30 ppm)/
1426 ms (40/50 ppm)
2989 ms (30 ppm)/
2313 ms (40/50 ppm)
2674 ms (30 ppm)/
2070 ms (40/50 ppm)
1708 ms (30 ppm)/
1322 ms (40/50 ppm)
676 ms
1324 ms
500 ms
500 ms
2000 ms