Download  Print this page

Control Circuit Terminals - Mitsubishi Electric FR-F720P-0.75K Instruction Manual

Fr-f700p series.
Hide thumbs

Advertisement

Wiring
2.4.5

Control circuit terminals

indicates that terminal functions can be selected using Pr. 178 to Pr. 196 (I/O terminal function selection) (Refer to Chapter 4 of
the Instruction Manual (Applied).)
(1) Input signals
Terminal
Terminal
Symbol
Name
Forward
STF
rotation start
Reverse
STR
rotation start
Start self-
STOP
holding
selection
RH,
Multi-speed
selection
RM, RL
Jog mode
JOG
selection
Second
RT
function
selection
MRS
Output stop
RES
Reset
Terminal 4
input selection
AU
PTC input
Selection of
automatic
CS
restart after
instantaneous
power failure
Contact input
common (sink)
(initial setting)
External
SD
transistor
common
(source)
24VDC power
supply common
External
transistor
common (sink)
(initial setting)
PC
Contact input
common
(source)
24VDC power
supply
20
Description
Turn ON the STF signal to start forward
rotation and turn it OFF to stop.
Turn ON the STR signal to start reverse
rotation and turn it OFF to stop.
Turn ON the STOP signal to self-hold the start signal.
Multi-speed can be selected according to the combination of RH,
RM and RL signals.
Turn ON the JOG signal to select Jog operation (initial setting)
and turn ON the start signal (STF or STR) to start Jog operation.
Turn ON the RT signal to select second function.
When the second function such as "second torque boost" and
"second V/F (base frequency)" are set, turning ON the RT signal
selects these functions.
Turn ON the MRS signal (20ms or more) to stop the inverter
output.
Use to shut off the inverter output when stopping the motor by
electromagnetic brake.
Use to reset fault output provided when fault occurs.
Turn ON the RES signal for more than 0.1s, then turn it OFF.
In the initial status, reset is set always-enabled. By setting Pr.75,
reset can be set enabled only at fault occurrence. Inverter
recovers about 1s after the reset is released.
Terminal 4 is valid only when the AU signal is turned ON. (The
frequency setting signal can be set between 0 and 20mADC.)
Turning the AU signal ON makes terminal 2 (voltage input)
invalid.
AU terminal is used as PTC input terminal (thermal protection of
the motor). When using it as PTC input terminal, set the AU/PTC
switch to PTC.
When the CS signal is left ON, the inverter restarts automatically at
power restoration. Note that restart setting is necessary for this
operation. In the initial setting, a restart is disabled.
(Refer to
Pr. 57 Restart coasting time in Chapter 4 of the Instruction
Manual (Applied).)
Common terminal for contact input terminal (sink logic) and terminal
FM.
Connect this terminal to the power supply common terminal of a
transistor output (open collector output) device, such as a
programmable controller, in the source logic to avoid malfunction by
undesirable currents.
Common output terminal for 24VDC 0.1A power supply (PC terminal).
Isolated from terminals 5 and SE.
Connect this terminal to the power supply common terminal of a
transistor output (open collector output) device, such as a
programmable controller, in the sink logic to avoid malfunction by
undesirable currents.
Common terminal for contact input terminal (source logic).
Can be used as 24VDC 0.1A power supply.
Specifications
When the STF and
STR signals are turned
ON simultaneously, the
stop command is given.
Input resistance
4.7kΩ
Voltage at
opening: 21 to
27VDC
Contacts at
short-circuited: 4
to 6mADC
Power supply
voltage range
19.2 to 28.8VDC
Permissible load
current 100mA
Rated
Refer to
Page
61
*2
65
*2
*2
*2
116
69
*2
*2
---- ------- ------ ---
24

Advertisement

Table of Contents

   Also See for Mitsubishi Electric FR-F720P-0.75K

Comments to this Manuals

Symbols: 0
Latest comments: