Download  Print this page

Mitsubishi Electric FR-F720P-0.75K Instruction Manual Page 189

Fr-f700p series.
Hide thumbs

Advertisement

(2) IPM parameter initialization list
By selecting IPM motor control from the parameter setting mode or with Pr. 998 IPM parameter initialization, the
parameter settings in the following table change to the settings required to drive an IPM motor. The changed
settings differ according to the IPM motor specification (capacity). Refer to the IPM motor specification list
shown later in this section.
Performing parameter clear or all parameter clear sets back the parameter settings to the settings required to
drive a general-purpose motor.
Parameter
Name
1
Maximum frequency
4
Multi-speed setting (high speed)
9
Electronic thermal O/L relay
13
Starting frequency
15
Jog frequency
18
High speed maximum frequency
Acceleration/deceleration
20
reference frequency
22
Stall prevention operation level
37
Speed display
55
Frequency monitoring reference
56
Current monitoring reference
71
Applied motor
80
Motor capacity
Terminal 2 frequency setting gain
125 (903)
frequency
Terminal 4 frequency setting gain
126 (905)
frequency
144
Speed setting switchover
240
Soft-PWM operation selection
PWM frequency automatic
260
switchover
263
Subtraction starting frequency
Power failure deceleration time
266
switchover frequency
374
Overspeed detection level
390
% setting reference frequency
*1
505
Speed setting reference
Current average value monitor
557
signal output reference current
870
Speed detection hysteresis
Regeneration avoidance
885
compensation frequency limit
value
Energy saving monitor reference
893
(motor capacity)
*1
This parameter can be set when FR-A7NL is mounted.
When Pr. 80 Motor capacity  "9999," the Pr. 80 Motor capacity setting is not changed by IPM parameter initialization, which is performed
*2
by setting Pr. 998 IPM parameter initialization or the parameter setting mode on the operation panel.
*3
Initial values differ according to the inverter capacity. (55K or lower/75K or higher)
General-
purpose
(rotations per minute)
motor
0 (Initial
Pr. 998
setting)
Maximum motor rotations
120/60Hz *3
Rated motor rotations per
60Hz
Rated inverter
current
Minimum rotations per
0.5Hz
Minimum rotations per
5Hz
Maximum motor rotations
120/60Hz *3
Rated motor rotations per
60Hz
120%
0
Rated motor rotations per
60Hz
Rated inverter
current
0
9999
Rated motor rotations per
60Hz
Rated motor rotations per
60Hz
Number of motor poles +
4
1
1
Rated motor rotations per
60Hz
Rated motor rotations per
60Hz
Maximum motor rotations
9999
60Hz
60Hz
Rated inverter
current
Speed detection hysteresis
0Hz
Minimum rotations per
6Hz
Rated inverter
capacity
Setting
IPM motor
1 (MM-EF),
12 (MM-EFS,
MM-THE4)
Maximum motor frequency
per minute
Rated motor frequency
minute
Rated motor current
Minimum frequency
minute
Minimum frequency
minute
Maximum motor frequency
per minute
Rated motor frequency
minute
Short-time motor torque
0
Rated motor frequency
minute
Rated motor current
120 (when Pr.998 = "1 or 101")
210 (when Pr.998 = "12 or 112")
Inverter capacity *2
Rated motor frequency
minute
Rated motor frequency
minute
Number of motor poles
100
0
1
Rated motor frequency
minute
Rated motor frequency
minute
Maximum motor frequency
per minute  105%
Rated motor frequency
Rated motor frequency
Rated motor current
Speed detection hysteresis
rotations per minute
Minimum frequency
minute
Motor capacity (Pr. 80)
4/8
IPM motor
increments
(frequency)
101 (MM-EF),
112 (MM-EFS,
1, 12
MM-THE4)
1r/min
1r/min
0.01A/0.1A *3
1r/min
1r/min
1r/min
1r/min
1r/min
0.01A/0.1A *3
0.01kW/0.1kW *3
1r/min
1r/min
1r/min
1r/min
1r/min
 105%
0.01A/0.1A *3
1r/min
frequency
1r/min
0.01kW/0.1kW *3
BCN-C22005-639
Setting
0, 101,
112
0.01Hz
0.01Hz
0.01Hz
0.01Hz
0.01Hz
0.01Hz
0.1%
1
0.01Hz
1
0.01Hz
0.01Hz
1
1
1
0.01Hz
0.01Hz
0.01Hz
0.01Hz
0.01Hz
0.01Hz
0.01Hz

Advertisement

Table of Contents

   Also See for Mitsubishi Electric FR-F720P-0.75K

Comments to this Manuals

Symbols: 0
Latest comments: