Download  Print this page

Mitsubishi Electric FR-F720P-0.75K Instruction Manual Page 128

Fr-f700p series.
Hide thumbs

Advertisement

Operation Panel
Indication
Name
Regenerative brake prealarm
Appears if the regenerative brake duty reaches or exceeds 85% of the Pr. 70 Special regenerative brake
duty value. When the setting of Pr. 70 Special regenerative brake duty is the initial value (Pr. 70 ="0"), this
warning does not occur. If the regenerative brake duty reaches 100%, a regenerative overvoltage (E.
OV_) occurs.
Description
The RBP signal can be simultaneously output with the [RB] display. For the terminal used for the RBP
signal output, assign the function by setting "7" (positive logic) or "107" (negative logic) in any of Pr. 190
to Pr. 196 (output terminal function selection). (
Appears only for the 75K or higher.
• Check that the brake resistor duty is not high.
Check point
• Check that the Pr. 30 Regenerative function selection and Pr. 70 Special regenerative brake duty values are
• Increase the deceleration time.
Corrective action
• Check the Pr. 30 Regenerative function selection and Pr. 70 Special regenerative brake duty values.
Operation Panel
Indication
Name
Electronic thermal relay function prealarm
Appears if the cumulative value of the Pr. 9 Electronic thermal O/L relay reaches or exceeds 85% of the
preset level. If it reaches 100% of the Pr. 9 Electronic thermal O/L relay setting, a motor overload trip (E.
THM) occurs.
Description
The THP signal can be simultaneously output with the [TH] display. For the terminal used for the THP
signal output, assign the function by setting "8" (positive logic) or "108" (negative logic) in any of Pr. 190
to Pr. 196 (output terminal function selection). (
· Check for large load or sudden acceleration.
Check point
· Is the Pr. 9 Electronic thermal O/L relay setting is appropriate? (Refer to page 52.)
· Reduce the load weight or the number of operation times.
Corrective action
· Set an appropriate value in Pr. 9 Electronic thermal O/L relay. (Refer to page 52.)
Operation Panel
Indication
Name
Maintenance signal output
Indicates that the cumulative energization time of the inverter has reached a given time.
Description
When the setting of Pr. 504 Maintenance timer alarm output set time is the initial value (Pr. 504 = "9999"),
this protective function does not function.
The Pr. 503 Maintenance timer setting is larger than the Pr. 504 Maintenance timer alarm output set time
Check point
setting. (
Corrective action
Setting "0" in Pr. 503 Maintenance timer erases the signal.
Operation Panel
Indication
Name
Parameter copy
Appears when parameters are copied between models with capacities of 55K or lower and 75K or
Description
higher.
Resetting of Pr.9, Pr.30, Pr.51, Pr.52, Pr.54, Pr.56, Pr.57, Pr.70, Pr.72, Pr.80, Pr.90, Pr.158, Pr.190 to Pr.196,
Check point
Pr.557 and Pr.893 is necessary.
Corrective action
Set the initial value in Pr. 989 Parameter copy alarm release.
(3) Alarm
When an alarm occurs, the output is not shut off. You can also output an alarm signal by making parameter
setting. (Set "98" in any of Pr. 190 to Pr. 196 (output terminal function selection). (
Instruction Manual (Applied).)
Operation Panel
Indication
Name
Fan alarm
For the inverter that contains a cooling fan,
Description
stops due to a fault or different operation from the setting of Pr. 244 Cooling fan operation selection.
Check point
Check the cooling fan for an alarm.
Corrective action
Check for fan failure. Please contact your sales representative.
RB
correct.
TH
MT
Refer to Chapter 4 of the Instruction Manual (Applied).)
CP
FN
Causes and corrective actions
FR-PU04
RB
FR-PU07
Refer to Chapter 4 of the Instruction Manual (Applied))
FR-PU04
TH
FR-PU07
Refer to Chapter 4 of the Instruction Manual (Applied))
FR-PU04
————
FR-PU07
MT
FR-PU04
————
FR-PU07
CP
FR-PU04
FN
FR-PU07
appears on the operation panel when the cooling fan
Refer to Chapter 4 of the
121
6

Advertisement

Table of Contents

   Also See for Mitsubishi Electric FR-F720P-0.75K

Comments to this Manuals

Symbols: 0
Latest comments: