Routing Effect Settings; Program Effects Settings - Korg Oasys Operation Manual

When effects are applied to the external input sound
from the AUDIO INPUT 1, 2, 3, 4, and S/P DIF IN
jacks, certain effect types or parameter settings may
cause oscillation to occur. If this occurs, adjust the

Routing effect settings

The insert effects, master effects, and total effect have
the same structure in all modes, but the routing
settings will determine how the oscillators of a
program or the timbres of a combination or track of a
song will be sent to each insert effect, master effect or
total effect. In the pages that follow, we will explain
how you can make routing settings and effect settings
in each mode.

Program Effects settings

Routing
1. Access the Program P8: Insert Effect– Routing
page.
2. Use Bus Select (IFX/Indiv. Out Assign) to specify
the bus to which the oscillator output will be sent.
If you want the oscillator output to be input to
insert effect 1, choose IFX1.
L/R: The output will not be sent to the total effects.
After passing through the total effect, the sound will
be sent to AUDIO OUTPUT (MAIN) L/MONO and
R.
IFX1–12: The output will be sent to insert effect IFX
1–12.
1–8, 1/2–7/8: The output will be sent to AUDIO
OUTPUT (INDIVIDUAL) 1–8. It will not be sent to
the insert effects, the master effects, or the total
effects.
Off: The output will not be sent to AUDIO
OUTPUT (MAIN) L/MONO, R, or to
(INDIVIDUAL) 1–8. Choose this if you want the
signal to be series‐connected to the master effects at
the send levels specified by "Send 1 (MFX1)" and
"Send 2 (MFX2)."
3. OSC MFX Send specifies the send level from each
oscillator to the master effects.
This can be set only when "Bus Select
(IFX/Indiv.Out Assign)" is either L/R or Off.
input level, output level, or effect parameters. Please
be aware of this particularly when using an effect
that has a high gain.
If "Bus Select (IFX/Indiv.Out Assign)" is set to IFX1–
12, the send level to the master effects is set by
Send1 and Send2 (Insert FX page) after the signal
passes through the insert effects.
4. "FX Control Bus (All OSCs to)" sends the
oscillator 1 and 2 output to the FX Control bus. Use
this if you want the audio input to the effect to be
controlled by a different sound.
You can use the two FX Control buses to control
effects freely. (See PG p.575 "4. FX Control Bus")
5. REC Bus sends the oscillator 1 and 2 output to the
REC buses.
In the P0– Audio Input/Sampling page, you can set
the Sampling Setup Source Bus to a REC bus, and
sample the signal being sent to the REC bus.
Normally you will turn this Off, since you will
usually set Source Bus to L/R when sampling the
output of oscillator 1 and 2.
Insert effects
6. Access the Insert FX page.
7. Choose the effect type that you want to use for
each insert effect IFX1–12.
When you press the popup button, all effects will be
displayed, organized into nine categories. Use the
pages located at the left to select a category, and
select an effect from that category on the LCD
screen.
You can use the "Copy Insert Effect" page menu
command to copy effect settings from another
program etc. Also, you can use "Swap Insert Effect"
to exchange (for example) IFX1 and IFX12.
8. Press the On/Off button to turn on the insert
effect.
Each time you press the button, the insert effect will
be switched on/off. When Off, the result will be the
same as when 000: No Effect is selected. The input
sound will be output without change.
9. Make Chain settings.
Routing effect settings
189