Appendix 2 Control Mode-Based Parameter (Function) Correspondence Table And Instruction Code List - Mitsubishi Electric FR-A720-0.4K Instruction Manual

Fr-a700 series
Hide thumbs Also See for FR-A720-0.4K:
Table of Contents

Advertisement

Appendix 2 Control mode-based parameter (function) correspondence
table and instruction code list
*1
These instruction codes are used for parameter read and write by using Mitsubishi inverter protocol with the RS-485 communication.
(Refer to page 333 for RS-485 communication)
*2
Validity and invalidity according to operation mode are as follows:
:Usable parameter
×
:Unusable parameter
Δ :Parameters available only during position control set by parameter
×
*3
" " indicates valid and "
*4
Parameters can be used with conditions. Refer to page 203 for details.
*5
These parameters are communication parameters that are not cleared when parameter clear (all clear) is executed from RS-485 communication.
(Refer to page 328 for RS-485 communication)
When a communication option is installed, parameter clear (lock release) during password lock (Pr. 297 ≠ 9999) can be performed only from the
*6
communication option.
Symbols in the table indicate parameters which function when an option is mounted.
......FR-A7AX,
......FR-A7AY,
......FR-A7NC,
......FR-A7NCE,
Name
0
Torque boost
1
Maximum frequency
2
Minimum frequency
3
Base frequency
4
Multi-speed setting (high speed)
5
Multi-speed setting (middle speed)
6
Multi-speed setting (low speed)
7
Acceleration time
8
Deceleration time
9
Electronic thermal O/L relay
DC injection brake operation
10
frequency
DC injection brake operation
11
time
DC injection brake operation
12
voltage
13
Starting frequency
14
Load pattern selection
15
Jog frequency
Jog acceleration/
16
deceleration time
17
MRS input selection
High speed maximum
18
frequency
19
Base frequency voltage
Acceleration/deceleration
20
reference frequency
Acceleration/deceleration
21
time increments
Stall prevention operation
22
level (torque limit level )
Stall prevention operation
23
level compensation factor at
double speed
Multi-speed setting (speed
24
4)
25
Multi-speed setting (speed 5)
466
" indicates invalid of "parameter copy", "parameter clear", and "all parameter clear".
.............FR-A7AR,
.........FR-A7ND,
Instruction
Code
* 1
control
00
80
0
01
81
0
02
82
0
03
83
0
04
84
0
05
85
0
06
86
0
07
87
0
08
88
0
09
89
0
0A
8A
0
0B
8B
0
0C
8C
0
0D
8D
0
0E
8E
0
0F
8F
0
10
90
0
11
91
0
12
92
0
13
93
0
14
94
0
15
95
0
16
96
0
17
97
0
18
98
0
19
99
0
.........FR-A7AP,
..........FR-A7AL,
.........FR-A7NL,
.........FR-A7NP,
Control Mode-based Correspondence Table
Advanced
Vector control
magnetic
V/F
flux
Speed
Torque
vector
control
control
control
×
×
×
×
×
×
×
×
×
×
×
.........FR-A7AZ,
.........FR-A7NS,
*2
Real sensorless
vector control
Position
Speed
Torque
control
control
control
×
×
×
×
×
×
×
×
×
Δ
Δ
Δ
Δ
Δ
×
×
×
×
*4
*4
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Δ
Δ
×
×
×
×
×
×
Δ
Δ
.........FR-A7AD,
.........FR-A7NF

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents