Download  Print this page

While Sewing - Brother 882-W20/W22 Operation Manual

Embroidery and sewing machine.
Hide thumbs
   
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420

Advertisement

Table of Contents
TROUBLESHOOTING
Problem
Pointer of the
With thick elastic fabric, the position will be
embroidery foot "W+"
misaligned only at raised parts in the fabric.
with LED pointer
With fabric having a very uneven surface, the
does not indicate the
position is not correctly aligned.
position correctly
Specifying with
The sensor pen has not been calibrated.
sensor pen cannot be
done accurately.
The pen is being held differently than when it
was calibrated.

■ While sewing

Problem
Machine does not
"Start/Stop" button was not pressed.
operate.
There is no pattern selected.
Presser foot is not lowered.
"Start/Stop" button was pressed with the foot
controller attached.
The "Start/Stop" button was pressed while the
machine is set for the sewing speed controller
to control the zigzag stitch width.
Needle breaks.
Needle is installed incorrectly.
Needle clamp screw is not tightened.
Needle is turned or bent.
Using improper needle or thread for the
selected fabric.
Wrong presser foot was used.
Upper thread tension is too tight.
Fabric is pulled during sewing.
Spool cap is set incorrectly.
There are scratches around the opening in the
needle plate.
There are scratches around the opening in the
presser foot.
There are scratches on the bobbin case.
Needle is defective.
A bobbin designed specifically for this
machine is not used.
Upper threading is incorrect.
Bobbin is set incorrectly.
Presser foot is attached incorrectly.
Screw of the presser foot holder is loose.
Fabric is too thick.
Fabric is fed forcefully when sewing thick
fabric or thick seams.
Stitch length is too short.
Stabilizer is not attached to fabric being
embroidered.
Bobbin thread is incorrectly wound.
390
Cause
Manually adjust the position according to the
thickness of the fabric.
The pointer indication should be used only as
a reference.
Before using the sensor pen for the first time,
be sure to calibrate it.
When using the sensor pen, be sure to hold it
at the same angle as when it was calibrated.
The specification location may be misaligned if
the pen is held at a slightly different angle. In
this case, make fine adjustments after making
the selection.
Cause
Press the "Start/Stop" button.
Select a pattern.
Lower the presser foot.
Remove the foot controller, or use the foot
controller to operate the machine.
Use the foot controller instead of the "Start/
Stop" button to operate the machine, or set
the "Width Control" to "OFF" in the settings
screen.
Reinstall the needle correctly.
Tighten the needle clamp screw.
Replace the needle.
Check the "Fabric/thread/needle
combinations" chart.
Use the recommended presser foot.
Adjust the thread tension.
Do not pull the fabric during sewing.
Check the method for attaching the spool cap,
then reattach the spool cap.
Replace the needle plate, or consult your
authorized Brother dealer.
Replace the presser foot, or consult your
authorized Brother dealer.
Replace the bobbin case, or consult your
authorized Brother dealer.
Replace the needle.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
Check the steps for threading the machine and
rethread the machine.
Reset the bobbin thread correctly.
Attach the presser foot correctly.
Securely tighten the screw of the presser foot.
Use fabric that the needle can pierce when the
handwheel is turned.
Allow the fabric to be fed without being
forcefully pushed.
Adjust the stitch length.
Attach stabilizer.
Use a correctly wound bobbin.
Solution
Solution
113, 170, 214, 313
"STITCH SETTING
Page
264
52
52
Page
17
17
83
33, 83
75
76
75
77
CHART"
92, 301
62
119
70
378
75
59
62
59
70
71
87
87
91
175, 256
54

Advertisement

Table of Contents

Troubleshooting

   Related Manuals for Brother 882-W20/W22

   Related Content for Brother 882-W20/W22

This manual is also suitable for:

82-w2282-w20Xv8500d882-w20882-w22

Comments to this Manuals

Symbols: 0
Latest comments: