Sanyo PLV-80 Service Manual page 63
Multimedia projector
Hide thumbs
Also See for PLV-80:
- Owner's manual (88 pages) ,
- Specifications (1 page) ,
- Specification sheet (1 page)
Table of Contents
Advertisement
Control Port Functions
Pin
Function Name
193 (Not used)
194 (Not used)
195 SH_EX_UART
196 (Not used)
197 (Not used)
198 LB_SH_UART
199 (Not used)
200 GND
201 EX_SH_UART
202 1.9V
203 (Not used)
204 FPGA_NCONFIG
205 BOX_RQST
206 NET_SW
207 GND
208 FPGA_CLB
209 3.3V
210 SYS SW_CPU
211 IC_RESET_CPU
212 LAMP_SWIN
213 FAN_DRIVE_CPU
214 SH_SDA_3V
215 SH_SCL_3V
216 SH_SDA_S3V
217 SH_SCL_S3V
218 PW_SH_0
219 UCLK
220 RESETP
221 (Not used)
222 MD3
223 MD4
224 3.3V
225 3.3V
226 (USB1P)[Func]
227 (USB1M)[Func]
228 GND
229 (USB2P)[Host]
230 (USB2M)[Host]
231 3.3V
232 GND
233 PRESS_SENS
234 (Not used)
235 KEY1
236 KEY2
237 3.3V
238 KEY3
239 OPT1
240 GND
Parallel I/O Expander(TE7780) (IC4801)
1 SH_PJ_UART1
2 GND
3 PJ_SH_UART1
4 (Not used)
5 (Not used)
6 (Not used)
7 (Not used)
8 Open
9 (Not used)
10 LENS_DOWN_EX
11 LENS_UP_EX
12 GND
13 SH_PW_0
14 PWR_LED_EX
15 READY_LED_EX
Function
SIOF Send Data/Output Port for SCI
SIOF Clock In/IO Port for SCI
Send Data2 [External]
SIOF Clock/IO Port for SCI
SIOF Frame Sync/IO Port for SCI
Dimmer Control
SIOF Receive Data/IO Port for SCI
Power (0V)
Receive Data2 [External]
Power (1.9V)
Start configuration
For PJ-Net
Switch On/Off for PJ-Net Power
Power for Inout/Output(0V)
Initialize for circuit
Power for Inout/Output(3.3V)
Bus Switch
Power Control peripheral ICs
Lamp Drive
Fan Drive
IIC Bus
IIC Bus
IIC Bus
IIC Bus
PW-SH Input SIgnal
USB Clock [48MHz]
Power On Reset Request
Hardware Reset Request
Bus Width Setting for Area0
Bus Width Setting for Area0
Test(3.3V Fixed)
USB Analog Power(3.3V)
USB1 Data I/O(+)
USB1 Data I/O(-)
USB Analog Power (0V)
USB2 Data I/O(+)
USB2 Data I/O(-)
USB Analog Power(3.3V)
Analog Power (0V)
Input for Pressure Sensor
KEY AD Converter Input
KEY AD Converter Input
Analog Power(3.3V)
KEY AD Converter Input
KEY AD Converter Input * Option Inut
Analog Power (0V)
For PJ-Net Command (SH: TXD)
For PJ-Net Command (SH: RXD)
Lens Shift Down
Lens Shift Up
Output Signal SH to PW
Power LED Drive
Ready LED Drive
Pol.
Action
-
(Open)
-
(Pull-up)
O
19200bps or 9600bps
-
(Pull-up)
-
(Pull-up)
I
Lamp Error Detection
-
(Pull-up)
-
-
I
19200bps or 9600bps
-
-
I
(Pull-up)
O
L -> H start configuration
O
Fixed L
O
L:On, H: Off
-
-
O
H after configuration
-
-
O
O
O
H: On, L: Off
O
H: On, L: Off
IO
L: Active
IO
L: Active
IO
L: Active
IO
L: Active
I
I
-
I
-
-
(Pull-up)
I
H Fixed
I
H Fixed
I
-
-
-
I/O
I/O
-
-
I/O
I/O
-
-
-
-
AI
(pull-down)
AI
AI
-
-
AI
AI
-
-
O
-
-
I
O
I
O
I
O
O
L: Active, H: Stop
O
L: Active, H: Stop
-
-
O
O
L: Light On Brightly, H: Light On Darkly
O
L: On, H: Off
-63-
Hide quick links:
Advertisement
Table of Contents
