Disassembly/Assembly Procedures Of Deck Mechanism - AEG VCR-D 4501 Service Manual

DISASSEMBLY/ASSEMBLY PROCEDURES
Before following the procedures described below, be sure to remove the deck assembly from the cabinet. (Refer to
CABINET DISASSEMBLY INSTRUCTIONS on page 1-6-1.)
All the following procedures, including those for adjustment and replacement of parts, should be done in Eject
mode; see the positions of [44] and [45] in Fig. DM1 on page 2-4-3. When reassembling, follow the steps in reverse
order.
STEP START-
/LOC. ING
No. No.
[1] [1] Guide Holder A
[2] [1] Cassette Holder Assembly T
[3] [2] Slider (SP)
[4] [2] Slider (TU)
[5] [4] Lock Lever
[6] [2] Cassette Plate
[7] [7] Cylinder Assembly
[8] [8] Loading Motor Assembly
[9] [9] AC Head Assembly
[10] [2] Tape Guide Arm Assembly T
[11] [10] C Door Opener
[12] [11] Pinch Arm (B)
[13] [12] Pinch Arm Assembly
[14] [14] FE Head Assembly
[15] [15] Prism
[16] [2] Slider Shaft
[17] [16] C Drive Lever (SP)
[18] [16] C Drive Lever (TU)
[19] [19] Capstan Motor
Clutch Assembly (HI)
[20]
[20]
Center Gear
[21] [20]
[22] [22] F Brake Assembly (HI)
[23] [22] Worm Holder
Pulley Assembly (HI)
[24] [22]
[25] Mode Gear
[25]
[26] Mode Lever (HI)
[20],[25]
[22],[23],
[27] Cam Gear (A) (HI)
[26]
[28] [26] TR Gear C
[29] [28] TR Gear Spring
[30] [29] TR Gear A/B
[31] [31] FF Arm (HI)
[32] [26] Idler Assembly (HI)
[33] [26] BT Arm
OF DECK MECHANISM
PART
Fig. No.
T DM3
DM4
T DM5
T DM5
T DM5
T DM5
T DM1,DM6
T DM1,DM7
T DM1,DM7
DM1,DM8
T DM1,DM8
T DM1,DM8
T DM1,DM8
T DM1,DM9
T DM1,DM9
T DM10
T DM10
T DM10
B DM2,DM11 3(S-8), Cap Belt
B DM2,DM12 (C-1)
B DM12
B DM2,DM12 *(L-6)
B DM2,DM13 (S-9),*(L-7),*(L-8)
B DM2,DM13
B DM2,DM13 (C-2)
B DM2,DM13 (C-3)
B DM2,DM13 (C-4)
B DM2,DM13 (C-5)
B DM13
B DM13
B DM1,DM13
B DM1,DM14 *(L-9)
B DM2,DM14 *(P-5)
2-4-1
REMOVAL
REMOVE/*UNHOOK/
UNLOCK/RELEASE/
UNPLUG/DESOLDER
2(S-1)
*(L-1), (S-1A)
*(L-2)
*(L-3),*(P-1)
Desolder, 3(S-2)
Desolder, LDG Belt,
2(S-3)
(S-4)
*(P-2)
*(L-4)
*(P-3)
(S-5)
(S-6)
*(L-5)
(S-7),*(P-4)
INSTALLATION
ADJUSTMENT
CONDITION
(+)Refer to Alignment
Sec.Pg.2-4-8
H9500DA