Table of Contents
Advertisement
HOW TO SET THE CORRECT TIME:
- YOU MUST USE ONLY THE REMOTE CONTROL KEYS TO SET THE CURRENT TIME OF
THE SET. (PLEASE DO NOT USE THE KEYS OF THE FRONT PANEL OF THE SET ITSELF).
- TO SET THE CORRECT CURRENT TIME, PLEASE FOLLOW THIS PROCEDURE:
PRESS & HOLD TIME/SNOOZE (ON REMOTE CONTROL) FOR 2 SECONDS.
THE DISPLAY WILL SHOW THE TIME AS HH:MM (HOURS : MINUTES),
AND YOU WILL SEE THAT "HH" IS FLASHING*.
WHILE "HH" IS FLASHING PRESS
SETTING (FORWARD OR BACKWARDS) TO THE HOUR OF THE CURRENT TIME.
THEN PRESS TIME/SNOOZE . NOW YOU WILL SEE THAT "MM" IS FLASHING.
WHILE "MM" IS FLASHING PRESS
SETTING (FORWARD OR BACKWARDS) TO THE MINUTES OF THE CURRENT
TIME. THEN PRESS TIME/SNOOZE . THE CORRECT CURRENT TIME IS NOW
STORED IN THE SET'S MEMORY.
* IMPORTANT: DURING THE TIME SETTING PROCEDURE, WHENEVER ANY PART OF THE
DISPLAY IS
(HH OR MM) IT MEANS THAT THE SET IS WAITING FOR YOU TO
FLASHING
ADJUST THE TIME. HOWEVER IF NO KEY IS PRESSED WITHIN 5 SECONDS, THE SET
WILL RETURN TO ITS NORMAL (PREVIOUS) OPERATING MODE.
AUTOMATIC WAKE-UP TIMER FUNCTION
- THIS SET HAS A TIMER FUNCTION TO ENABLE YOU TO AUTOMATICALLY SWITCH
"ON" (& "OFF") THE SET AT YOUR DESIRED PRESET TIMES. THIS IS USEFUL AS A
MORNING ALARM CLOCK.
HOW TO SET "WAKE UP" TIMER
1. PRESS THE
ON/STANDBY KEY TO SWITCH ON THE SET (DISPLAY BLUE
LIGHT WILL BE "ON").
2. PRESS THE
FUNCTION KEY TO SELECT THE MUSIC SOURCE THAT YOU WISH
\THE SET TO PLAY AT THE "WAKE UP" TIME:
PRESS
FUNCTION
RADIO
PRESS
AUX IN
FUNCTION
OR
KEYS TO CHANGE THE HOUR
OR
KEYS TO CHANGE THE MINUTES
PRESS
PRESS
FUNCTION
CD
FUNCTION
PRESS
CARD
FUNCTION
USB
E-5
3. ADJUST THE SETTINGS FOR THE SELECTED SOURCE. FOR EXAMPLE:
FOR RADIO : SELECT THE RADIO BAND (AM/FM) & TUNE IN THE DESIRED STATION.
FOR CD : PLACE THE DESIRED MUSIC CD DISC INTO THE CD TRAY
FOR USB : INSERT YOUR USB FLASH MEMORY PEN-DRIVE (WHICH CONTAINS
YOUR DESIRED MUSIC).
FOR SD-CARD : INSERT YOUR SD CARD FLASH MEMORY (WHICH CONTAINS YOUR
DESIRED MUSIC).
(NOTE: FOR "AUX IN" SOURCE YOU WILL NEED TO LEAVE THE EXTERNAL SOURCE
DEVICE "ON" & WITH PLAYBACK ACTIVATED, SO THIS TYPE OF SOURCE IS NOT
RECOMMENDED FOR WAKE UP TIMER FUNCTION).
4. ADJUST THE VOLUME LEVEL AS DESIRED BY PRESSING VOL + OR VOL -
5. PRESS THE ON/STANDBY KEY TO PUT THE SET INTO "STANDBY" MODE
(BLUE LIGHT OFF).
6. PRESS AND HOLD TIMER KEY (ON REMOTE CONTROL) UNTIL "TMR ON" APPEARS
IN THE DISPLAY. THEN IMMEDIATELY RELEASE THE
AGAIN ONCE. THE DISPLAY WILL NOW SHOW:
7. PRESS
AND
TO REACH THE HOUR OF THE DESIRED WAKE UP TIME THEN
PRESS TIMER KEY AGAIN ONCE. THE DISPLAY WILL NOW SHOW:
TIMER
8. PRESS
AND
TO REACH THE MINUTES OF THE DESIRED WAKE UP TIME,
THEN PRESS THE TIMER KEY. THE DISPLAY WILL SHOW "TMR OFF". THIS MEANS
THAT YOU MUST NOW INPUT THE TIME AT WHICH THE SET WILL SWITCH "OFF"
AUTOMATICALLY (AFTER IT HAS SWITCHED "ON" AT THE WAKE UP TIME WHICH
YOU SET).
9. WHEN THE DISPLAY SHOWS "TMR OFF" PRESS THE TIMER KEY ONCE. THE
"HOUR" DIGIT WILL FLASH IN THE DISPLAY. PRESS
HOUR OF THE DESIRED "SWITCH OFF" TIME. THEN PRESS TIMER ONCE AGAIN.
10. THE 2 "MINUTE" DIGITS WILL NOW FLASH IN THE DISPLAY. PRESS
REACH THE MINUTES OF THE DESIRED "SWITCH OFF" TIME. THEN PRESS TIMER
ONCE AGAIN.
TIMER KEY & PRESS IT
TIMER
0 00
FLASHING (HOUR)
8 00
FLASHING
(MINUTES)
AND
TO REACH THE
E-6
KEY.
AND
TO
Advertisement
Table of Contents
