Mitsubishi Electric FR-F720P-0.75K to 110K Instruction Manual page 378

Name
Manual controller
DC tach. follower
Three speed selector
Motorized speed setter
Ratio setter
Speed follower
Master controller
Soft starter
Deviation detector
Preamplifier
Pilot generator
Deviation sensor
Frequency setting
potentiometer
Frequency meter
(64mm × 60mm)
Calibration resistor
FR Configurator SW3
(Inverter setup software)
* Rated power consumption. The power supply specifications of the FR series manual controllers and speed controllers are 200VAC 50Hz, 220/
220VAC 60Hz, and 115VAC 60Hz.
Commercially available products
Name
Communication connector
Communication cable
•Blade terminals
Commercially available products (as of Jan. 2010)
·Phoenix Contact Co.,Ltd.
Wire Size
Terminal
Screw Size
M2
·NICHIFU Co.,Ltd.
Wire Size
Terminal
Screw Size
M2 0.3 to 0.75
Use shielded or twisted cable as the connection cable for the control circuit terminals. Separate the cable from the main
circuit and the high-power circuits (including the 200V relay sequence circuit).
When using a blade terminal (without insulation sleeve), take caution that the twisted wires do not come out.
Model
For independent operation. With frequency meter, frequency
FR-AX
setting potentiometer and start switch.
For synchronous operation (1VA) by external signal (0 to 5V,
FR-AL
0 to 10V DC) *
For three speed switching among high, middle and low
FR-AT
speed operation (1.5VA)*
For remote operation. Allows operation to be controlled from
FR-FK
several places (5VA)*
For ratio operation. Allows ratios to be set to five inverters.
FR-FH
(3VA)*
For tracking operation by a pilot generator (PG) signal
FR-FP
(3VA)*
Master controller (5VA) for parallel operation of multiple
FR-FG
(maximum 35) inverters.*
For soft start and stop. Enables acceleration/deceleration in
FR-FC
parallel operation (3VA)*
For continuous speed control operation. Used in
FR-FD
combination with a deviation sensor or synchro (5VA)*
FR-FA Used as an A/V converter or arithmetic amplifier (3VA)*
QVAH-10 For tracking operation. 70V/35VAC 500Hz (at 2500r/min)
YVGC-500W- For continuous speed control operation (mechanical
NS deviation detection). Output 90VAC/90°
WA2W 1kΩ For frequency setting. Wirewound 2W 1k B characteristic
YM206NRI Dedicated frequency meter (graduated to 120Hz). Moving-
1mA coil type DC ammeter
For frequency meter calibration. Carbon film type B
RV24YN 10kΩ
characteristic
FR-SW3- Supports an inverter startup to maintenance.
SETUP-W FR-SW1-SETUP-W
(as of Jan. 2010)
Model Manufacturer
5-554720-3 Tyco Electronics
SGLPEV-T
Mitsubishi Cable
(Cat5e/300m)
Industries, Ltd.
24AWG × 4
Blade Terminal Model
(with insulation
2
(mm )
sleeve)
0.3, 0.5 AI 0,5-6WH
Blade Terminal
2
Product Number
(mm )
BT 0.75-7
Options and products available on the market
Applications, Specifications, etc.
is also available for installation.
Applications, Specifications, etc.
Cat.5e cable that is compatible with TIA/EIA standards.
(10BASE-T/100BASE-T/1000BASE-T)
(without
insulation sleeve)
A 0,5-6
Insulation Product
Number
VC 0.75
Applicable for all
models
Applicable for all
models
RJ-45 connector
Blade Terminal
Crimping Tool
CRIMPFOX 6
Blade Terminal
Crimping Tool
NH 67
Applicable
Inverter
367