JRC JFV-700 Installation Manual

Color echo sounder.
Hide thumbs
COLOR ECHO SOUNDER
JFV-700 SERIES
JFV-700
JFV-700HP
INSTALLATION MANUAL
H-7ZPBS6504A

   Related Manuals for JRC JFV-700

   Summary of Contents for JRC JFV-700

  • Page 1

    COLOR ECHO SOUNDER JFV-700 SERIES JFV-700 JFV-700HP INSTALLATION MANUAL H-7ZPBS6504A...

  • Page 3: General Information

    This installation manual describes the installation, maintenance and inspection proce- dures for the JFV-700 series. Prior to the installation, users are requested to read this manual well and familiarize with its contents so that an optimum function may be derived from the JFV-700.

  • Page 4: Before You Begin

    Before You Begin Symbols Used In This Manual Related Symbols Marks In this manual, and on the equipment, we use several warning signs to call your attention to impor- tant to items that, if not handled correctly, could present danger to yourself or property. These warning note classifications are as described below.

  • Page 5: Usage Hints

    Usage Hints When installing this set, be sure to connect the grounding wire to the grounding terminal of the set. Otherwise, an electric shock can result when a failure or leakage occurred on the set. Do not damage, break or modify the power cord.

  • Page 6

    When removing the power cord, be sure to re- move the power cord terminal correctly. Pulling the power cord can damage it resulting in a fire or an electric shock. •@ Do not bring the set in a cooled state suddenly into a warm room.

  • Page 7: Table Of Contents

    General Information¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ ¥ 1 Before you Begin ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ ¥¥¥ 2 Usage Hints ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ ¥¥¥¥¥¥¥3 1 Configuration 1.1 List of Models ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ 1.2 List of Components ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ 7 2 Installation 2.1 Mounting of Echo Sounder ¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥ ¥¥¥¥¥¥¥¥¥¥¥¥¥¥...

  • Page 8: List Of Models

    •@•@•@•@•@•@•@•@ ‡@•@•@ •@‡A ‡B •@ ‡C ‡D ‡@ Model identification NO : JFV-700 1kw with vertical display. HP : JFV-700HP 3kw with vertical display. ‡A Characters used on the display panel J: Japanese E: English ‡B Selection of piezoelectric transducer...

  • Page 9: Optional Accessories, List Of Components

    1.2 List of Components Standard Components Description Model No. Quantity Remarks ‚P‚‹‚v ‚i‚e‚u•|‚V‚O‚O Echo sounder Any one of the two. ‚P ‚R‚‹‚v ‚i‚e‚u•|‚V‚O‚O‚g‚o Depends on the frequency Transducer 1 or 2 and mounting method. Spares 2 pieces of fuse. ‚V‚y‚w‚a‚r‚O‚O‚P‚T ‚P ‚V‚y‚b‚m‚`‚O‚W‚Q‚V‚` 3.0 meters long with 4P connec-...

  • Page 10

    2 Installation Do not install the set in a place that exposes the CRT to direct sun for a long time or a place whose environmental temperature can reach 55 degree Centigrade or above. Otherwise, fire hazards or system failure can result from such operating environment. Do not install the set on an unstable place such as shaky or in- clined bench.

  • Page 11: Mounting Of Echo Sounder

    2.1 Mounting of Echo Sounder (1) Mounting location 1. The transducer cable tends to pick up generate noise, thus the echo sounder must be installed in a location that can prevent interference between the cable and a co- axial cable on a radio equipment. 2.

  • Page 12

    (2) Mounting procedure 1. Loosen two main body fixing bolts situated at lower front side of the main body, then remove the mounting plate. 2. Drill four tapping screw holes (φ4 mm) in the main body mounting location. 3. Using the tapping screws attached to the main body, fix the mounting plate to the desk.

  • Page 13

    2.2 Connection Between Components...

  • Page 14: Connecting The Power Supply And Transducer Connectors

    2.3 Connecting the Power Supply and Transducer Connectors (1) Connecting the Power Cables 1. Use 7ZCNA0827A(CFQ-8827) for the power cable. 2. Connect the power cables as indicated below: Cable Connector pin number Polarity White Black Green Shield Connector case 3. When the installation requires to extend the power cable, the cable used must be DPYC-2.5 or above so that voltage on the connector when conducted may not go 10.2V or less.

  • Page 15

    (5) Transducer Cable Wiring Procedure 1. Don't try to bundle the transducer cable with other cables. When this cable is routed along with another cable, 50 cm minimum space must be provided between the them. 2. The cable on the echo sounder transducer tends to pick up or generate noise, thus it must not be bundled with the coaxial cable on the radio equipment.

  • Page 16

    2.4 Transducer Installation Procedure...

  • Page 21

    •@...

  • Page 25

    ‚Q•D‚T•@ List of Transducers Equipped •i‚P•j Single frequency...

  • Page 26

    •i‚Q•j Dual frequency...

  • Page 27: Grounding Work

    2.6 Grounding Work When installing the system, make sure that the grounding cable is connected to the grounding terminal. Otherwise, an electric shock can result when failure or leakage developed on the sys- tem. 1. For grounding of the echo sounder body,. 0.5 thick ×...

  • Page 28: Connecting Optional Equipment

    For water depth and vessel speed output. For the cursor position water depth output. (Input/output signal in the NMEA0183 format or JRC Clamp format) filter 1. When reading three or more outputs from J907 in parallel, the buffer (NQA-602DC) must be connected.

  • Page 29: Connecting The Water Temperature Sensor (thermistor Type)

    2.8 Connecting the Water Temperature Sensor (Thermistor type) Connecting the optional water temperature sensor allows the JFV-700/HP to display wa- ter temperature. Thermistor type water temperature sensor alone is connectable. For connecting NMEA type sensors (available from Murayama Ltd. and others), refer to Section 2.9.3.

  • Page 30

    Specification: 1. Speed sensor 22000 pulse/N.M (equivalent to 1.8 km) 2. Temperature sensor 10 KΩ/25 degree Centigrade 3. Cable length 10 meters Connector 8P Cable Nishin parts NS-1008 Sensor body Sensor body mounting nut 2-inch screw Housing mounting nut Housing ( unit : mm ) Water turbine (boat speed sensor)

  • Page 31: Output Of Sea Bottom Depth, Output Of Cursor Position Water Depth

    2.9 Connecting the External Equipment In order to connect the external equipment, the JFV-700/HP equips with the interface conformed to the JRC or NMEA0183 format. Output format is determined by input format. When input signal is absent, output is generated in the NMEA0183 format.

  • Page 32: Input Of Water Temperature Data (nmea Type Sensor)

    28 in the Instruction Manual. 2.9.3 Input of Water Temperature Data (NMEA type sensor) The JFV-700/HP allows to connect a water temperature sensor designed for the NMEA output format. When a thermistor type water temperature sensor (see Section 2.8) is connected, display of water temperature data from a NMEA type sensor is disabled.

  • Page 33

    2.9.4 Connection to Squid Fishing Gear ATTENTION Be sure to select “Display” for the cursor display. If you turn on •œ the function when “Off” is selected, improper data can be gener- ated. •œ Bubbles or thick plankton layer in the upper surface can prevent determining state of sea bottom.

  • Page 34: Connecting The Remote Controller (nch-466e), Actions Required After The Installation, Actions Taken For Noise Trouble

    2.10 Connecting the Remote Controller (NCH-466E) The JFV-700/HP accepts connection of the optional remote controller. The remote controller allows you to record or reproduce the screen data, and generating the water temperature and the water depth alarms. Connecting procedure: Connect to the connector to J902.

  • Page 35

    Route the power/transducer cable through the clamp filter The clamp filter used is ZCAT3035-1330 (for large diameter) from TDK Co. Clamp ¸×ÝÌß̨ÙÀ filter Cable through the clamp filter ‚P‚”•@¹°ÌÞÙ‚ðŠª‚- (2) Cable Routing Re-route the power cable and transducer cable so that they may not interfere with the cable from an affected equipment.

  • Page 36: Adjustment After Installation, Adjustment Of Frequency

    3 Adjustment After Installation 3.1 Adjustment of Frequency After making sure that the installation is complete and the wiring is acceptable, proceed to fine tuning of the frequency to place the transducer in an optimum condition. This adjustment shall be implemented at a pier. 1.

  • Page 37: Fishing Method And Corresponding Setup, Setup Changes Needed When Switched From Our Competitors

    3.2 Fishing Method and Corresponding Setup The following describes standard setting suited for each fishing method. Expressions used in the table below may vary according to the area our system is used and the given fishing method. The noise suppression is usually set to 3 or lower value. If you set the noise suppression to a higher value, weaker response may not be displayed on the screen.

  • Page 38: Frequency Change

    4 Frequency Change Do not start your operation as long as the CD857 LED is turned on. Otherwise, electric shock can result from touching the high potential block. ATTENTION Both JP701 and JP702, JP03 and JP704 must be changed at the •œ...

  • Page 39

    2. When 200 kHz is selected, the following modification is required. 200 kHz is output to the 5-pin connector (J905 A/B or A). Direct the output to the 3-in connector (J906 “B”) by the following modification. Remove P701 and P702, then insert P106 to the once P105 position and insert P105 to the once P106 position.

  • Page 40

    4.2 Changing to Dual Frequency Implement changes on the following components on the CML-560-1K/3K. For the entire view of the CML-560-1K/3K , see Figure 4.1 in page 40. CD857 •F Indication for high voltage. See the following 1, 2 and 3. 1.

  • Page 41

    1kW Unit CML-560-1K (for 7PCBS7035) JP721 JP722 JP725 JP726 JP723 JP724 JP727 JP728 high Voltage setting TX ON TX OFF High Freq. JP713 Low Freq. JP712 7 8 15 16 JP802 1-2 or Open 910 1 JP702 JP803 JP715 Initial setting JP714 for CFT-2505,CFT-205/505 JP721...

  • Page 42

    1kW Unit CML-560-1K (for 7PCBS7035A) 310220720520 JP721 - 1-2 1-2 1-2 JP801 JP801 7 9 15 JP722 1-2 1-2 1-2 JP725 - 2-4 1-2 3-4 8 10 16 JP726 3-4 3-4 3-4 3-4 - 3-4 3-4 3-4 JP802 JP723 2-3 - 2-3 2-3 JP724 2-3 - 2-3 2-3 JP727...

  • Page 43

    3kW Unit CML-560-3K (for 7PCBS7035) JP721 JP722 JP725 JP726 JP723 JP724 JP727 JP728 high Voltage setting TX ON TX OFF High Freq. JP713 Low Freq. JP712 7 8 15 16 JP802 910 1 JP702 JP803 JP715 Initial setting for JP714 CFT-220/CFT-520 JP721 JP724...

  • Page 44

    3kW Unit CML-560-3K (for 7PCBS7035A) JP721 JP801 JP801 JP722 JP725 8 10 JP726 JP802 JP723 JP724 JP727 JP728 - TX high voltage TX trigger setting setting JP803 High Freq. JP713 1-2 High Freq. JP701/702 2-3 Low Freq. JP712 1-2 Low Freq. JP703/704 JP802 2-3 Initial setting for CFT-220/CFT-520...

  • Page 49: Implementing The Master Reset

    4.3 Implementing the Master Reset ATTENTION The transducer can be damaged by an improper setting. The •œ master reset may not be implemented for any purpose other than the frequency change. •œ When you have selected a transducer not installed, repeat the master reset again.

  • Page 50

    Table 4.3. (4) Description on the backup 1. The JFV-700/HP employs EEPROM for the backup. Unlike current models, it does not require a lithium battery replacement. However, since it is an electronic component, damages can occur if your turn power off while the master reset is taking place.

  • Page 51

    Table 4.3 List of Combinations Obtainable from the Mater Reset Frequency combination 200/75 CFT-205/CFT-705 CFT-220/CFT-720 CFT-210/CFT-710 CFT-210/CFT-710 CFT-220/CFT-720 CFT-205/CFT-705 200/50 CFT-2505KD CFT-220/CFT-520 CFT-2505K CFT-210/CFT-510 CFT-2510K CFT-2510K CFT-210/CFT-510 CFT-2505KD CFT-220/CFT-520 CFT-2505K 200/38 CFT-210/CFT-410 CFT-220/CFT-420 CFT-220/CFT-420 CFT-210/CFT-410 200/28 CFT-205/CFT-310 CFT-220/CFT-320 CFT-210/CFT-310 CFT-210/CFT-310 CFT-220/CFT-320 CFT-205/CFT-310 75/50...

  • Page 52: Parts List And Assembly Drawing

    5 Appendix 5.1 Parts List and Assembly Drawing Table 5.1 JFV-700/HP Mechanical Parts List NAME Q'ty JRC PARTS NUMBER 1 PANEL ASSEMBLY ‚l‚o‚a‚b‚R‚S‚V‚U‚T 2 PANEL BOARD ‚l‚s‚s‚R‚O‚U‚X‚O‚O 3 CONTACT RUBBER ‚l‚s‚u‚R‚O‚R‚O‚U‚S 4 LIGTH GUIDE ‚l‚s‚u‚R‚O‚R‚O‚Q‚S 5 V-RING ƒÓ‚R ‚l‚s‚u‚R‚O‚R‚O‚U‚R 6 V-RING ƒÓ‚U ‚l‚s‚u‚R‚O‚R‚O‚T‚T...

  • Page 54: System Setting As Delivered

    5.2 System Setting as Delivered Table 5.3 System Setting Table as Delivered JFV-700/700HP Item System setting as delivered Description Standard CUSTOM 1 CUSTOM 2 CUSTOM 3 Range Shift Chart feed speed Graph No backup provided A scope No backup provided...

  • Page 55

    Table 5.3 (CONTINUE) JFV-700/700HP Item System setting as delivered Description Standard CUSTOM 1 CUSTOM 2 CUSTOM 3 FUNCTION SHALLOW DEPTH FUNCTION DEEP DEPTH FUNCTION TEMP UPPER UPPER LIMIT 20.0•Ž 20.0•Ž 70.0 ß F 20.0•Ž FUNCTION TEMP LOWER LOWER LIMIT 10.0•Ž...

  • Page 56

    Table 5.4 User Color Initial Setting Table STANDARD and CUSTOM1 DAY/NIGHT : DAY BACK COLOR BACK COLOR BACK COLOR BACK COLOR BACK COLOR :STANDARD User color number DAY/NIGHT : DAY COLOR MODE BACK COLOR BACK COLOR BACK COLOR BACK COLOR :STANDARD User color number Normal 14/Discrimination-...

  • Page 57

    CUSTOM2 DAY/NIGHT : DAY BACK COLOR BACK COLOR BACK COLOR BACK COLOR BACK COLOR :STANDARD User color number DAY/NIGHT : DAY COLOR MODE BACK COLOR BACK COLOR BACK COLOR BACK COLOR :STANDARD User color number Normal 14/Discrimination- Normal 15/Discrimination 14 Normal-/Discrimination15 DAY/NIGHT : NIGHT BACK COLOR...

  • Page 58

    CUSTOM3 DAY/NIGHT : DAY BACK COLOR BACK COLOR BACK COLOR BACK COLOR BACK COLOR :STANDARD User color number DAY/NIGHT : DAY COLOR MODE BACK COLOR BACK COLOR BACK COLOR BACK COLOR :STANDARD User color number Normal 14/Discrimination- Normal 15/Discrimination 14 Normal-/Discrimination15 DAY/NIGHT : NIGHT BACK COLOR...

  • Page 59

    5.3 Menu Tree MAIN MENU „¥„Ÿ„Ÿ STD. RANGE „ „¥„Ÿ„Ÿ PRESET „ „ „¥„Ÿ„Ÿ RANGE1 5•`2000 m „ „ „¥„Ÿ„Ÿ RANGE2 5•`2000 m „ „ „¥„Ÿ„Ÿ RANGE3 5•`2000 m „ „ „¥„Ÿ„Ÿ RANGE4 5•`2000 m „ „ „¥„Ÿ„Ÿ RANGE5 5•`2000 m „...

  • Page 60

    FISH FINDER SETTING MENU „¥„Ÿ„Ÿ INTERFERENCE OFF AUTO „¥„Ÿ„Ÿ COLOR REJ. „ „¥„Ÿ„Ÿ SELECT LEVEL „ „¤„Ÿ„Ÿ CLEAR DISPLAY „¥„Ÿ„Ÿ WHITE LINE „ „¥„Ÿ„Ÿ HI 0.0•`10.0 „ „¤„Ÿ„Ÿ LO 0.0•`10.0 „¥„Ÿ„Ÿ PDC „ „¥„Ÿ„Ÿ HI „ „¤„Ÿ„Ÿ LO „¥„Ÿ„Ÿ FREQ. ADJUST „...

  • Page 66

    For further information contact: HEAD OFFICE & HEAD OFFICE & HEAD OFFICE & HEAD OFFICE & Akasaka Twin Tower (Main), SALES DEPT. SALES DEPT. SALES DEPT. SALES DEPT. 17-22, Akasaka 2-chome, Minato-ku, Tokyo 107-8432 JAPAN Phone : +81-3-3584-8711 : +81-3-3584-8715 Telex : 0242-5420 JRCTOK J MAIN PLANT MAIN PLANT...

This manual also for:

Jfv-700hp

Comments to this Manuals

Symbols: 0
Latest comments: