Resuming Recording In Cliplink Mode - Sony DSR-300 Service Manual

ClipLink Shooting
4
Press the TAKE button when you find a shot
where you would like to set a Mark IN point.
TAKE button
The TAKE/TALLY indicator (orange) lights in the
viewfinder and "TAKE" appears on the screen.
5
Press the TAKE button when you find a shot
where you would like to set a Mark OUT point.
The TAKE/TALLY indicator (orange) goes out in
the viewfinder and the "TAKE" disappears from
the screen.
At this time, the time code (HH:MM:SS) at the
Mark IN/OUT point for scene 001 is recorded to
the camcorder's internal memory, and then
recorded to the cassette memory.
To set/clear NG
If you press the NG button before you set the next
Mark IN point, the previous scene will be
designated as "NG" ("NG" appears on the screen).
Once NG has been set, you can cancel it by
pressing the NG button again before you set the
next Mark IN point (the "NG" on the screen
disappears).
6
Repeat steps 4 and 5 as needed to record time
codes at Mark IN/OUT points, scene numbers, and
NG designations to cassette memory.
The scene number is automatically incremented
each time you specify a Mark IN point.
7
To finish shooting, press the VTR button on the
camcorder or lens.
This stops the recording operation.
The Index Pictures of each Mark IN point are
recorded onto the tape (when the DSBK-301 is
fitted).
68
Chapter 3 Shooting
Setting Cue points as you shoot
The following data is recorded onto the cassette when
you specify a Cue point to highlight a scene.
• Time codes (HH:MM:SS) for Rec IN/OUT points
• Time codes (HH:MM:SS:frame) for Cue points
• Scene number: The scene number counter is
automatically incremented with each Rec OUT point
specification.
• NG designation, cassette name/number (if set from
the camcorder)
• Index Pictures for all Rec IN points (when the
DSBK-301 is fitted): these are recorded each time
recording is stopped.
Perform the following procedure.
1
Perform steps 1 to 3 in "ClipLink Shooting"
(pages 65 and 66).
2
Access basic menu page 5 and perform the
following operations.
1) Set MARK/CUE to CUE.
The ClipLink mode indication "CLIP C"
appears on the viewfinder screen.
2) Set the cassette name or number if necessary.
For details of menu operations, see "Basic Menu
Operations" (page 78).
3
Press the VTR button on the camcorder or lens.
The camcorder starts recording, and the REC/
TALLY indicator lights in the viewfinder.
4
Press the TAKE button when you find a shot
where you would like to set a Cue point.
The "CUE" indication appears (for about 1 second)
on the viewfinder screen. At this point, the time
code (HH:MM:SS:frame) at the Cue point is
recorded into the cassette memory.
5
Repeat step 4 to specify more Cue points.
6
To finish shooting, press the VTR button on the
camcorder or lens.
This stops recording operation.

Resuming Recording in ClipLink Mode

During recording pause in ClipLink mode, pressing the
STOP/PLAY/F FWD/REW buttons, performing edit
search, or ejecting the cassette will interrupt the
ClipLink shooting. With this state, it is impossible to
start back space editing using ClipLink function. (The
ClipLink continue mode is canceled and indication
in the display window disappears.) If you resume
CONT
recording on the same cassette, the previously recorded
data will be overwritten.
2,3
4
1
Perform step 2 to 10 in "Basic Procedure for
Shooting" (page 47) and step 2 (page 51) in
"Recording on the Internal VCR".
2
Insert a cassette if one is not already loaded.
The and indications should appear in the
CL
display window.
Note
If the is flashing, it means abnormality of the
CL
cassette memory. In this case, it is impossible to
continue recording from that data on ClipLink
mode.
Time codes (HH:MM:SS) and scene number
(scene 001) are recorded to the cassette memory
and the Index Picture of the Rec IN point is
recorded onto the tape (when the DSBK-301 is
attached).
You can avoid this and continue recording in ClipLink
mode from the previous recording stop point by
performing the following steps.
Note
If you stop recording during the first ten seconds of
recording, you may not be able to use these steps to
continue recording in ClipLink mode.
2
3
Check the following points.
Result and response
Check point
CLIP and If these indications do not appear in
IP
the display window, access the
(when the DSBK-
301 is fitted) VCR menu and set ClipLink
function to on (see page 97).
appear in the
display window
Remaining clips Make sure there are enough
capacity for recording clips (see
page 17).
(Continued)
69
Chapter 3 Shooting