Brother KE-434C Instruction Manual page 63

<Memory switches 30 - 4F>
30 to 4F are set by entering two-digit values.
These values are incremented using the P2 switch, and decremented using the P4 switch.
Switch Possible setting range
memo-30 0 - 99
memo-31 0 - 60
memo-32 12 - 25
memo-33 1 - 10
memo-34 0 - 5
memo-35 3 - 9
−
memo-36
memo-37 1 - 20
memo-38 1 - 20
memo-39 1 - 20
memo-3A 1 - 20
memo-3b 1 - 20
memo-3c 0 - 99
−
memo-3d
−
memo-3E
−
memo-3F
memo-40 1 - 5
memo-41* 1 - 99
0 - 10
memo-42
0 - 13
memo-43 1 - 3
memo-44 0 - 3
memo-45
−
-
memo-4F
*KE-435C only.
13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES
Units Initial value
Limits the maximum area in the horizontal direction (X).
mm 99 (If the value is set to 99, the maximum length allowed will be 100
mm)
mm 60 Limits the maximum area in the vertical direction (Y).
× 100rpm
25 Changes the maximum sewing speed.
Changes the feed timing.
× 7.5°
5
1 (Fast) ← 5 (Standard) → 10 (Slow)
The (setting value + 1) number of stitches are sewn at the speed
Stitch 0 set by memo-35 at the sewing start. (No low-speed sewing if set
to 0.)
Changes the sewing start speed for the number of stitches
× 100rpm
4
specified by memo-34.
− −
−
Changes the feed timing one stitch before the sewing end.
× 7.5°
10
1 (Fast) ← 10 (Standard) → 20 (Slow)
× 7.5°
10 Changes the feed timing two stitches before the sewing end.
× 7.5°
10 Changes the feed timing for the third stitch at the sewing start.
× 7.5°
10
Changes the feed timing for the second stitch at the sewing start.
× 7.5°
10 Changes the feed timing for the first stitch at the sewing start.
Sets the number of stitches for which the feed timing (memo-33
setting) is enabled.
Stitch 0 0: Enabled for all stitches
1 - 99: Enabled for the specified number of stitches from the
sewing start
− − −
− −
−
− −
−
Changes the test feeding speed (with no material).
−
4
1 (Fast) ←→ 5 (Slow)
× 10ms
10 Changes the standby time after the stepping foot is raised.
For KE-434C solenoid specifications, the work clamp operating
mode can be changed. (When set to "0", the mode is selected
0
−
according to the settings for DIP switches A-1 and A-2.)
Refer to "14. SETTING THE WORK CLAMP MODE" for details of
the available modes.
0
KE-434C pneumatic specifications and KE-435C
−
5 KE-434C inner clamping device specifications
Changes the allowable speed/sewing pitch.
−
3
1 (Fast) ←→ 3 (Standard)
Changes the path taken when moving from the machine home
position to the start position.
0
0: Across inside of work clamp, 1: Top-left, 2: Bottom-left,
−
3: Bottom-right
KE-434C inner clamping device specifications (Does not pass
1
across inside of clamp)
− −
−
KE-434C,435C
Explanation
57