Kenmore Lavadora de Platos Use & Care Manual page 16

If your unit has a display similar to the one shown above,
follow the instructions below.
CANCELING A CYCLE
• Open the door.
• Hold down the CANCEL button until the "WASHING"
LED goes out. Close the door.
• Wait for about 1 minute until the dishwasher drains.
• The "COMPLETE" LED will illuminate. This indicates that
the unit has been reset.
CHANGING A CYCLE
If you need to change the running cycle to a new cycle:
• Open the door.
• Hold down the CANCEL button until the "WASHING"
LED goes out.
• Wait for about 1 minute until the dishwasher drains.
• The "COMPLETE" LED will illuminate. This indicates that
the unit has been reset.
• Press "POWER" button to turn the unit off. Then press
the "POWER" button again to turn the unit back on.
• You can now select a new cycle.
To enter the options mode:
(rinse aid setting, dry assist)
• Door must be open. Press the "POWER" button to turn
the unit on.
• One of the wash cycle LEDs will be flashing.
• Press and hold the ">" button, then press and release
the "START" button. Now release the ">" button.
• The "Sanitized" and one other LED will be flashing. You
are now in the options setup mode.
• Press ">" to select the option you would like to adjust.
If the "COMPLETE" and "RINSE AID" LEDs are flashing, you
are in the "Rinse Aid" mode. You can adjust the amount of
Rinse Aid dispensed.
If the "COMPLETE" and "SANITIZED" LEDs are flashing,
you are in the "Dry Assist" mode. You can now activate or
deactivate Dry Assist.
If the "COMPLETE", "SANITIZED", and "RINSE AID" LEDs
are flashing, you are in the "Cycle Completion Signal"
mode. You can now increase or decrease the tone or
deactivate the signal.
OPERATING THE DISHWASHER
To set the amount of Rinse Aid:
NOTE: If your glasses have spots on them, you need more
rinse agent. If your glasses have streaks, you need less Rinse
Agent.
Follow the instructions to enter "options" mode. With the
"COMPLETE" and "RINSE AID" LEDs flashing :
• Press the "<" button to change the amount of rinse
•
Dry Assist
With this option you can raise the temperature of the
rinse water and increase the drying time for improved
drying.
Follow the instructions to enter "options" mode. With the
"COMPLETE" and "SANITIZED" LEDs flashing:
• Press the "<" button to activate or deactivate dry assist.
•
Cycle Completion Signal (select models)
The cycle completion signal alerts you when a cycle
completes and the dishwasher has washed and dried the
dishes. You can choose to disable the tone or adjust the
volume.
Follow the instructions to enter "options" mode. With the
"COMPLETE" and "RINSE AID" LEDs flashing:
• Press the "<" button to adjust or deactivate the cycle
•
Time Delay
This option allows you to delay the start time of your cycle.
To activate:
•
•
•
•
16
agent dispensed.
0 LEDs lit → rinse aid dispenser is OFF
1 LED lit → Lowest amount of rinse aid dispensed
2 LEDs lit → Medium amount of rinse aid dispensed
3 LEDs lit → Highest amount of rinse aid dispensed
Press "START" to save your settings.
0 LEDs lit → extra dry heat is OFF
1 LED lit → extra dry heat is ON
Press "START" to save your settings.
completion signal.
0 LEDs lit → cycle completion signal is OFF
1 LED lit → Lowest tone level
2 LEDs lit → Medium tone level
3 LEDs lit → Highest tone level
Press "START" to save your settings.
Turn the dishwasher on.
Select the desired wash cycle.
Press the Delay Start button until the desired delay time
illuminates in the "3Hr", "6Hr", "9Hr" LED.
Press "START" to save your settings.