Instruction for use & installation instructions miniBar HiPro 3000 HiPro 4000 HiPro 6000 HiPro Vision English Dometic absorption refrigerators for hotels & offices MBA 10/2011 Record for future reference: N 1-1 Model number ..........Product number ..........Type H20 / 60 Serial number ..........
Explanation of symbols used in this manual You have made an excellent choice in selecting the Dometic Absorption miniBar. We are sure Warning notices that you will be satisfied with your new miniBar in all respects. The miniBar, which works silently, Warning notices are identified by symbols.
It is not permitted that this product be disposed of by way of the normal household refuse collection system. Dometic refrigerators bear this sym- bol on the data plate to be found in the interior of the unit. 1.9.2 Energy-saving tips Do not expose the miniBar to direct sunlight or any other heat source (e.g.
Safety instructions 2.0 Safety instructions Application according to Working upon and checking regulations the miniBar This miniBar is intended for free-standing instal- WARNING! lation (miniBar with unit cover) or installation in furniture (miniBar without unit cover). Work on electrical facilities must be carried Only use the miniBar for chilling and storing clo- authorised personnel...
Installation 3.0 Installation Air passing through the duct must not be Unpacking preheated by any source of heat. Ventilation grills, if used, must have ope- Check during unpacking that the device is nings of at least 200cm² each. defect-free. Report transport damage to the transport company immediately.
Installation Securing When being built into a cupboard or a recess, the miniBar must be positioned in such a manner that both hinges/feet of the unit lie flush. The miniBar is then (see Figures a, b) screwed, at its hinges, to the piece of furniture in question. In the case of units with 8mm feet and with LED option for the door opening control, the reflector delivered with the unit must also be installed in...
BROWN : LIVE If the connection cable is damaged it must be replaced by the Customer Service at Dometic, or by respectively qualified per- sonnel, in order to prevent any hazards. Fig. 10 Fig. 9 As the colours of the wires in the mains lead...
If the fuse cover-carrier is lost, a replaceement can be obtained from the Dometic Service Centers. The fuse cover/carrier must be of the same colour as that of the coloured insert in the base of the plug.
Installation Changing the doorhang The (optional) LED of the door-opening control is placed always opposite the hanging side. Fig. 22 Fig. 21 Pull the lower hinges forwards, pull out the door with the hinge. Fig. 15 Fig. 24 Fig. 23 appliance with feet Remove the upper hinge pin and insert on the Fig.
Remark (devices without doorlock): Additional installation of a door lock is possi- ble (available from Dometic) In the door the position for the opening is prepared. Drill the hole in accordance to the drawing above.
Technical data HiPro Vision Casing Plastic HiPro 3000 Gross contents (litres) Dimensions (mm) Casing Plastic (H x W x D) 559 x 405 x 465 Gross contents (litres) Electrical rating (W) Dimensions (mm) Power consumption (H x W x D)
Operation 4.0 Operating instructions Temperature control Cleaning The miniBar is equipped with completely auto- Before operating the miniBar, we recommend you matic, electronic temperature control. Using an clean it both inside and outside. optional remote control, the default setting can Use a soft cloth, lukewarm water and a mild be changed from 5 °C to 3 °C, 7 °C or 12 °C detergent.
Fig. 35 Fig. 34 LED of the door-opening control flashes synchro- nously , if available.) Please contact the authorized Dometic Service if a failure occurs. HiPro miniBars, which are designed for use on sea vessels, are equipped with a bimetal sen- sor switch instead ! Malfunction of the cooling Fig.
Operation Interior light Remote control Two LEDs (1) light the cooling compartment whilst the door is opened. Two sensors (2) control the LEDs and the (optio- nal) door control as well. Fig. 38 Automatic Door Control [ADC] (optional) Fig. 42 The LED (1) placed at the bottom edge of the Type 1 miniBar indicates whether the miniBar door has...
Operation 4.10 Troubleshooting Failure : No cooling (the aggregate at the back of the device is cold). Possible Cause Self Help Authorised Service a.) The device plug is not a.) Plug in device plug. plugged in. b.) No voltage in socket. b.) Check main fuse.
Page 19
Fabrik / Factory : Dometic GmbH In der Steinwiese 16 D-57074 Siegen (Germany) Modelle / Models : HiPro 3000, HiPro 4000, HiPro 6000, HiPro Vision Typenklasse / Type family : H 20/60 Produktdaten / Product data : HiPro 3000 HiPro 4000...