Basic Operations; Turn On The Power; Select The Source To Play - JVC RX-ES9SL Instructions Manual

Basic operations

TV DIRECT SETTING ADJUST SURROUND
DVD MULTI
STANDBY / ON STANDBY
HOME CINEMA CONTROL CENTER
AUDIO
TV DIRECT
DVD VCR STB TV
DVD VR STB TV
DVD MULTI FM/AM TV/VIDEO MUTING
TV VOL CHANNEL VOLUME
DVD
AUDIO/TV
/VCR/STB
TUNING FM MODE TUNING
MEMORY
TA/NEWS/INFO
TOP MENU MENU
PTY ENTER PTY
ON
CHOICE SCREEN
DISPLAY
PTY SEARCH
AUDIO SUBTITLE TITLE/GROUP RETURN
ZOOM BASS TREBLE
1 2 3
BASS TREBLE
VFP 4 5 6
7 8 9
ANGLE TV RETURN 100 +
10 0 +10
REPEAT
3D
DIMMER SLEEP ANALOG/DIGITAL CANCEL
INPUT
SMART S. SETUP
BASS BOOST A.POSITION
TONE
SURROUND
TEST EFFECT DECODE
SUBWFR CENTER L SURR R
1

Turn on the power

Press STANDBY/ON
control).
The STANDBY lamp goes off. The current source indicator lights in
red. The name of the current source (or station frequency) appears on
the display.
Current volume level is shown here.
ANALOG L C R
SUBWFR LFE
LS RS
Current source name appears.
To turn off the power (into standby)
Press STANDBY/ON again (or
The STANDBY lamp lights up.
NOTE
A small amount of power is consumed in standby mode. To turn the
power off completely, unplug the AC power cord.
11-14_RX-ES9SL[B]f
SOURCE SELECTOR MASTER VOLUME
/ MULTI JOG
SET / TUNER PRESET
DVD STB VR TV FM / AM
When operating the receiver
using the remote control,
always set the mode selector
to AUDIO/TV/VCR/STB.
(or AUDIO on the remote
VOL
AUDIO on the remote control).
11
2

Select the source to play

PHONES
On the front panel:
Turn SOURCE SELECTOR until the source name
you want appears on the display.
The source indicator corresponding to the selected source lights in
red.
• As you turn SOURCE SELECTOR, the source changes as follows:
ANALOG L C R
SUBWFR LFE
LS RS
VR (VR DIGITAL)
DVD MULTI DVD (DVD DIGITAL)
STB (STB DIGITAL)
From the remote control:
Press one of the source selecting buttons.
• Each time you press FM/AM, FM and AM (MW) changes
alternately.
DVD MULTI: Select the DVD player using the analogue
discrete output mode (5.1 channel reproduction).
To enjoy the DVD MULTI playback, see page 34.
*
DVD (DIGITAL) : Select the DVD player.
*
STB (DIGITAL) : Select the STB.
*
VR (DIGITAL) : Select the VR.
TV: Select the TV tuner.
FM: Select an FM broadcast.
AM: Select an AM (MW) broadcast.
NOTE
After pressing VR on the remote control, you can operate the VCR by
using the remote control but not the VDR. See page 35 and 37 for
details.
* Selecting the analogue or digital input mode
When you have connected the VR, STB, or DVD player using both the
analogue connection and the digital connection methods (see pages 7
to 9), you need to select the correct input mode.
• You can select the digital input only for sources which you have
selected digital input terminals for. (See "Setting the digital input
(DIGITAL IN) terminals—DIGITAL IN" on page 19.)
From the remote control ONLY:
Press ANALOG/DIGITAL INPUT to select the
analogue or digital input mode.
• Each time you press the button, the input mode alternates between
the analogue input ("ANALOGUE") and the digital input ("DGTL
AUTO").
DGTL AUTO: Select for the digital input mode. The receiver
automatically detects the incoming signal format,
then the digital signal format indicator (DOLBY D,
DTS or LPCM) for the detected signals lights up.
ANALOGUE*: Select for the analogue input mode.
* Initial setting
NOTE
You cannot select the digital input mode when selecting "DVD MULTI"
as the playing source.
03.6.27, 16:45
VOL
TV
FM AM
(Back to the beginning)
11