Selecting The Fm Reception Mode - JVC LVT1002-001B Instructions Manual

Tuner operations
3
Press the numeric buttons (1 – 10, +10) to select
a channel number while the channel number
position is flashing.
• For channel number 5, press 5.
• For channel number 15, press +10, then 5.
• For channel number 30, press +10, +10, then 10.
ANALOG
L R
SUBWFR
4
Press MEMORY again while the selected channel
number is flashing on the display.
The station is assigned to the selected channel number.
• The selected channel number stops flashing.
ANALOG L R
SUBWFR
5
Press repeatedly or hold TUNING 9 or
TUNING ( to select another frequency you want
to store.
6
Repeat steps 1 to 5 until you store all the
stations you want.
To erase a stored preset station
Storing a new station on a used channel number erases the
previously stored one.
To tune in a preset station
From the remote control:
1
Press FM/AM to select the band.
The last received station of the selected band is tuned in and the
numeric buttons now work for tuner operations.
• Each time you press the button, the band alternates between
FM and AM (MW).
ANALOG L R
SUBWFR
2
Press the numeric buttons (1 – 10, +10) to select
a channel number.
If you select "FM" or "AM" using SOURCE SELECTOR on the
front panel, press FM/AM on the remote control before this
operation.
• For channel number 5, press 5.
• For channel number 15, press +10, then 5.
• For channel number 30, press +10, +10, then 10.
ANALOG L R
SUBWFR
24
On the front panel:
STANDBY / ON STANDBY
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
TUNED ST AUTO MUTING
MH
Z canceled before you finish, start from step 2 again.
VOL
1
Turn SOURCE SELECTOR to select "FM" or
"AM."
The last received station of the selected band is tuned in.
2
Press TUNER PRESET.
"P" appears on the display and MULTI JOG now works for
TUNED ST AUTO MUTING
selecting preset channels.
MH
Z
VOL
3
Turn MULTI JOG to select a preset channel
number during "P" appears on the display.
• Turning MULTI JOG clockwise increases the preset channel
numbers.
• Turning MULTI JOG counterclockwise decreases the preset
channel numbers.
ANALOG

Selecting the FM reception mode

When an FM stereo broadcast is hard to receive or noisy, you can
change the FM reception mode while receiving an FM broadcast.
• You can store the FM reception mode for each preset station (see
page 23).
From the remote control ONLY:
While listening to an FM station, press FM MODE.
If you select "FM" using SOURCE SELECTOR on the front panel,
press FM/AM on the remote control before this operation.
TUNED ST AUTO MUTING
MH
Z
• Each time you press the button, the FM reception mode alternates
VOL
between "AUTO MUTING" and "MONO."
AUTO MUTING*:
MONO:
TUNED ST AUTO MUTING
MH
Z
VOL
* Initial setting
TV DIRECT SETTING ADJUST SURROUND
DVD MULTI DVD STB VCB TV
L R
SUBWFR
Normally select this.
When a program is broadcast in stereo, you
will hear stereo sound; when in monaural, you
will hear monaural sound. This mode is also
useful to suppress static noise between
stations. The AUTO MUTING indicator lights
up on the display.
Select this to improve the reception (but
stereo effect will be lost).
In this mode, you will hear noise while tuning
in to the stations. The AUTO MUTING
indicator goes off from the display. (The ST
indicator also goes off.)
SOURCE SELECTOR MASTER VOLUME
/ MULTI JOG
SET / TUNER PRESET
PHONES
FM / AM
TUNED ST AUTO MUTING
MH
Z
VOL